Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Adnan Khan
Stats
Member since
09-05-2011
160
Posts
0
Helpful
0
Solutions
Created by
Adnan Khan
in Wireless and Mobility
in Wireless and Mobility
10-05-2019
11:25 PM
10-05-2019
11:25 PM
Hi, Many thanks for your support. Actually, the unit secondary was Active that is why I was not able to install the license however, I kept disconnected the secondary unit during license installation.
... View more
Created by
Adnan Khan
in Wireless and Mobility
in Wireless and Mobility
10-03-2019
08:04 AM
10-03-2019
08:04 AM
I will do that tomorrow and update here in both cases success or faliure.
... View more
Created by
Adnan Khan
in Wireless and Mobility
in Wireless and Mobility
10-03-2019
02:09 AM
10-03-2019
02:09 AM
Thanks for the reply. You mean if I power down secondary WLC. "command" option under Management -> Software Activation -> Licenses will re appear again?
... View more
Created by
Adnan Khan
in Wireless and Mobility
in Wireless and Mobility
10-02-2019
10:02 PM
10-02-2019
10:02 PM
I am trying to install additional AP license in controller but "Command" option is not showing under Management -> Sofware Activation section to install license also I tried via CLI and getting error " License Installation is blocked by secondary controller" I have WLC in HA and secondary is Hot standby. Please suggest how I can install the license.
... View more
Labels:
09-30-2019
01:42 AM
Hi , Its a new config and i dont want wo messup with the network due lack of multicast knowledge. I would really apprexiatw if u can give the requires config for this scnario. Isp is same and do i need to use 232 ramge ip for server or 239 can be used om ebgp?
... View more
09-30-2019
01:30 AM
Hi, Many thanks for the reply. I have attached my topology. If you can give me the only muticast related configuration according to the diagram, really appreciate for your help.
... View more
09-29-2019
11:26 PM
I want to consifure IP multicast routing between eBGP Peers and I have two routers on same location and HSRP is running between them on LAN facing interfaces . Assume I have similar type of config on other side of the router. What will be multicast config for eBGP also do I need specific multicast IP address like 232 range instead 239 and also do i need to configure multicast querier. Firewall is placed behind the routers (in HA) and firewall has all the gateway for LAN Switching side. R1 router bgp 100 bgp log-neighbor-changes network 172.x.x.x redistribute static neighbor 192.168.100.2 remote-as 200 R2 router bgp 100 bgp log-neighbor-changes network 172.x.x.x redistribute static neighbor 192.168.100.3 remote-as 200
... View more
Labels:
Created by
Adnan Khan
in Network Management
in Network Management
09-03-2019
08:00 AM
09-03-2019
08:00 AM
I enabled SNMP on Prime Server through CLI so I can get messages on another server about the Prime Server status.
... View more
09-02-2019
11:14 PM
Hi Leo, I have configured Cisco Prime HA with Appliance and VM combination. It is do able, however there is no Cisco documentation is available for such design.
... View more
Created by
Adnan Khan
in Network Management
in Network Management
09-02-2019
10:24 PM
09-02-2019
10:24 PM
We usually monitor devices via Cisco Prime but If I want to monitor Cisco Prime server for its availability and logs how I can configure SNMP on Prime to monitor by remote logging server.
... View more
Labels:
07-10-2019
01:06 AM
When I am trying to generate cpu utilization report in Cisco Prime. it is given me output : "No data matches the specified criteria for the report" make sure that the following poll jobs are running. 1. Switch CPU and memory poll 2. Controller Performance
... View more
Labels:
02-09-2019
09:29 PM
Hi I am getting below error while doing HA. Please assist someone which SW version mismatch.
... View more
Labels:
01-20-2019
12:58 AM
Yes this is I suspect too but is there any document from Cisco perticulalry mentioned this design not supported (Appliance and VM) or if u can share link for HA for both appliance to appliance or VM to VM.
... View more
01-20-2019
12:21 AM
Hi,
Can we do Cisco Prime HA with one appliance and one VM if yes then is there any design document from Cisco?
Regards,
... View more
Labels:
01-10-2019
03:04 AM
Hi,
Stackwise virtual command will show up when you upgrade to IOS Fuji-16.9.2 ED.
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9400/software/release/16-9/release_notes/ol-16-9-9400.html
... View more
10-05-2019
Hi, Many thanks for your support. Actually, the unit secondary was
Active that is why I was not able...
10-03-2019
Thanks for the reply. You mean if I power down secondary WLC. "command"
option under Management -> S...
10-02-2019
I am trying to install additional AP license in controller but "Command"
option is not showing under...
09-30-2019
Hi ,Its a new config and i dont want wo messup with the network due lack
of multicast knowledge. I w...
09-30-2019
Hi, Many thanks for the reply. I have attached my topology. If you can
give me the only muticast rel...
09-29-2019
I want to consifure IP multicast routing between eBGP Peers and I have
two routers on same location ...
Created by
Adnan Khan
in Network Management
09-03-2019
09-03-2019
I enabled SNMP on Prime Server through CLI so I can get messages on
another server about the Prime S...
09-02-2019
Hi Leo, I have configured Cisco Prime HA with Appliance and VM
combination. It is do able, however t...
Created by
Adnan Khan
in Network Management
09-02-2019
09-02-2019
We usually monitor devices via Cisco Prime but If I want to monitor
Cisco Prime server for its avail...
07-10-2019
When I am trying to generate cpu utilization report in Cisco Prime. it
is given me output :"No data ...
Created by
Adnan Khan
in Firewalls
02-09-2019
02-09-2019
Hi I am getting below error while doing HA. Please assist someone which
SW version mismatch.
01-20-2019
Yes this is I suspect too but is there any document from Cisco
perticulalry mentioned this design no...
01-20-2019
Hi, Can we do Cisco Prime HA with one appliance and one VM if yes then
is there any design document ...
Public Statistics
| Date Registered | 09-05-2011 10:09 PM |
| Date Last Visited | 10-09-2019 12:10 AM |
| Total Messages Posted | 160 |
Helpful Votes Given To
| User | Helpful Count |
|---|---|
| 5 | |
| 5 | |
| 5 | |
| 5 | |
| 5 |
.jpg "VIP Advisor"){kind=icon}
