Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About rogierboeken
10-19-2017
Stats
Member since
01-17-2007
87
Posts
10
Helpful
0
Solutions
Re: wap121 with single point setup - fo...
in Wireless and Mobility
01-13-2014
01:35 AM
01-13-2014
01:35 AM
i had not thought about disabling the lowerrates on the AP and have done that but it still went out looking for other AP. in the end i disabled single point setup and blocked the AppleTV by entering its mac address on the mac filter (block) and moved the AP where it had better coverage (FirePlace was blocking most of the signal intermittently) cheers
... View more
10-25-2010
03:17 AM
hi i could not get it to work with straight thru cables and when i tried with a cross over cable it initially did not work either, until i bought 4 brand new crossover cables and now it is working fine. there must have been some cabling fault in the crossover cable because with the brand new ones it is working fine and i have a 4gb connection between the 2 servers. cheers
... View more
08-04-2010
03:50 AM
since changing the westek bonding the macflap errors have disappeared i did have an issue where the SAN/iscsi read and write throughput went down drastically but after re-inserting the nics this seems to have resolved itself and i am now getting much better results (110MB/ps write and 80MB/ps read) i have done testing with shutting down 1 member of the stack and randomly unplugging nics and the througput remains the same and without macflap errors
... View more
08-04-2010
03:48 AM
the 2 switches are connected directly with 4x straigh thru ethernet cables i ran the tdr tests and everything is showing up as normal only difference is that the 3750 reports the length to be +- 4 meters and the 2960 +-0 meters Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi1/0/1 1000M Pair A 1 +/- 0 meters N/A Normal Pair B 2 +/- 0 meters N/A Normal Pair C 2 +/- 0 meters N/A Normal Pair D 2 +/- 0 meters N/A Normal Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi1/0/1 1000M Pair A 2 +/- 4 meters N/A Normal Pair B 2 +/- 4 meters N/A Normal Pair C 2 +/- 4 meters N/A Normal Pair D 2 +/- 4 meters N/A Normal as i have a support contract with the company that did the installation they are testing this in their lab and will get back to me with any changes i need to make, i will report back as soon as i hear from them cheers!
... View more
08-03-2010
08:52 AM
the westek nics are bonded using this method balance-rr Transmissions are received and sent out sequentially on each bonded slave interface. This mode provides fault tolerance and load balancing. I am not sure how this translates to the cisco terminology they basically have the following bonding possibilities balance-rr Transmissions are received and sent out sequentially on each bonded slave interface. This mode provides fault tolerance and load balancing. active-backup Only one slave in the bond is active. Another bonded slave interface is only used if the active bonded slave interface fails. This mode provides fault tolerance. balance-xor Transmission is based on the following equation: [(the source MAC address XOR'd with the destination MAC address) modulo (slave count)]. This selects the same slave for each destination MAC address. This mode provides fault tolerance and load balancing. broadcast Transmits everything on all slave interfaces. This mode provides fault tolerance. 802.3ad IEEE 802.3ad Dynamic link aggregation. Creates aggregation groups that share the same speed and duplex settings. Utilizes all slaves in the active aggregator according to the 802.3ad specification. Requires a switch that supports IEEE 802.3ad Dynamic link aggregation. balance-tlb Channel bonding that does not require any special switch support. The outgoing traffic is distributed according to the current load (computed relative to speed) on each slave. Incoming traffic is received by the current slave. If the receiving slave fails, another slave takes over the MAC address of the failed receiving slave. This mode provides fault tolerance and load balancing. the consultant who helped me setting this up suggested i change the bonding to balance-tlb and otherwise balance-xor I will have a play with this and let you know how i get on
... View more
08-03-2010
08:33 AM
hi i have a 2960s configured in a stack (2x 960s) i have configured 2 vlans vlan103 which is a iscsi vlan with a westek SAN connected, the Westek San has 4 nics bonded with 1 ip and mac address it is connected to ports 1/0/23, 1/0/24, 2/0/23 and 2/0/24 i noticed the following macflap errors Aug 3 14:43:15.441: %SW_MATM-4-MACFLAP_NOTIF: Host 024e.8f46.cf32 in vlan 103 i s flapping between port Gi2/0/24 and port Gi2/0/23 Aug 3 14:43:30.005: %SW_MATM-4-MACFLAP_NOTIF: Host 024e.8f46.cf32 in vlan 103 i s flapping between port Gi1/0/24 and port Gi1/0/23 Aug 3 14:43:44.151: %SW_MATM-4-MACFLAP_NOTIF: Host 024e.8f46.cf32 in vlan 103 i s flapping between port Gi2/0/23 and port Gi1/0/24 Aug 3 14:43:59.512: %SW_MATM-4-MACFLAP_NOTIF: Host 024e.8f46.cf32 in vlan 103 i s flapping between port Gi1/0/24 and port Gi1/0/23 on the sam vlan in port 1/0/21 and 2/0/21 i have a server which also has a bonded nic but no such issues, i have an identical server on port 1/0/22 and 2/0/22 which is also working fine so it is something to do with the Westek SAN and its nic bonding below is the config from the switch should i setup an etherchannel on those ports in vlan103 which have the macflap errors as per this link http://www.sadikhov.com/forum/index.php?showtopic=151540 anyway here is my config Building configuration... Current configuration : 6388 bytes ! ! Last configuration change at 15:42:21 UTC Tue Aug 3 2010 ! NVRAM config last updated at 13:04:00 UTC Tue Aug 3 2010 ! version 12.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname 2960stack ! boot-start-marker boot-end-marker ! no logging console enable secret level 5 5 enable secret 5 ! ! ! macro global description cisco-global no aaa new-model clock summer-time UTC recurring last Sun Mar 1:00 last Sun Oct 2:00 switch 1 provision ws-c2960s-24ts-l switch 2 provision ws-c2960s-24ts-l authentication mac-move permit ip subnet-zero ! ! udld aggressive ! mls qos map cos-dscp 0 8 16 24 32 46 48 56 mls qos srr-queue output cos-map queue 1 threshold 3 5 mls qos srr-queue output cos-map queue 2 threshold 3 3 6 7 mls qos srr-queue output cos-map queue 3 threshold 3 2 4 mls qos srr-queue output cos-map queue 4 threshold 2 1 mls qos srr-queue output cos-map queue 4 threshold 3 0 mls qos srr-queue output dscp-map queue 1 threshold 3 40 41 42 43 44 45 46 47 mls qos srr-queue output dscp-map queue 2 threshold 3 24 25 26 27 28 29 30 31 mls qos srr-queue output dscp-map queue 2 threshold 3 48 49 50 51 52 53 54 55 mls qos srr-queue output dscp-map queue 2 threshold 3 56 57 58 59 60 61 62 63 mls qos srr-queue output dscp-map queue 3 threshold 3 16 17 18 19 20 21 22 23 mls qos srr-queue output dscp-map queue 3 threshold 3 32 33 34 35 36 37 38 39 mls qos srr-queue output dscp-map queue 4 threshold 1 8 mls qos srr-queue output dscp-map queue 4 threshold 2 9 10 11 12 13 14 15 mls qos srr-queue output dscp-map queue 4 threshold 3 0 1 2 3 4 5 6 7 mls qos queue-set output 1 threshold 1 138 138 92 138 mls qos queue-set output 1 threshold 2 138 138 92 400 mls qos queue-set output 1 threshold 3 36 77 100 318 mls qos queue-set output 1 threshold 4 20 50 67 400 mls qos queue-set output 2 threshold 1 149 149 100 149 mls qos queue-set output 2 threshold 2 118 118 100 235 mls qos queue-set output 2 threshold 3 41 68 100 272 mls qos queue-set output 2 threshold 4 42 72 100 242 mls qos queue-set output 1 buffers 10 10 26 54 mls qos queue-set output 2 buffers 16 6 17 61 mls qos ! ! ! spanning-tree mode rapid-pvst spanning-tree loopguard default spanning-tree etherchannel guard misconfig spanning-tree extend system-id ! ! ! errdisable recovery cause link-flap errdisable recovery interval 60 ! vlan internal allocation policy ascending ! ! ! interface Port-channel1 switchport access vlan 3 switchport mode access spanning-tree portfast ! interface FastEthernet0 ip address 172.16.3.3 255.255.255.0 ! interface GigabitEthernet1/0/1 description switch_3750-1/0/1 switchport access vlan 3 switchport mode access speed 1000 duplex full channel-group 1 mode on ! interface GigabitEthernet1/0/2 description switch_3750-2/0/2 switchport access vlan 3 switchport mode access speed 1000 duplex full channel-group 1 mode on ! interface GigabitEthernet1/0/3 ! interface GigabitEthernet1/0/4 switchport access vlan 3 switchport mode access ! interface GigabitEthernet1/0/5 ! interface GigabitEthernet1/0/6 ! interface GigabitEthernet1/0/7 ! interface GigabitEthernet1/0/8 ! interface GigabitEthernet1/0/9 ! interface GigabitEthernet1/0/10 ! interface GigabitEthernet1/0/11 ! interface GigabitEthernet1/0/12 ! interface GigabitEthernet1/0/13 ! interface GigabitEthernet1/0/14 ! interface GigabitEthernet1/0/15 ! interface GigabitEthernet1/0/16 ! interface GigabitEthernet1/0/17 ! interface GigabitEthernet1/0/18 ! interface GigabitEthernet1/0/19 ! interface GigabitEthernet1/0/20 ! interface GigabitEthernet1/0/21 description vmco 1 nic 1 switchport access vlan 103 switchport mode access speed 1000 duplex full ! interface GigabitEthernet1/0/22 description vmco 2 nic 1 switchport access vlan 103 switchport mode access speed 1000 duplex full ! interface GigabitEthernet1/0/23 description westek nic 1 switchport access vlan 103 switchport mode access speed 1000 duplex full ! interface GigabitEthernet1/0/24 description westek nic 3 switchport access vlan 103 switchport mode access speed 1000 duplex full ! interface GigabitEthernet1/0/25 ! interface GigabitEthernet1/0/26 ! interface GigabitEthernet1/0/27 ! interface GigabitEthernet1/0/28 ! interface GigabitEthernet2/0/1 description switch_3750-2/0/1 switchport access vlan 3 switchport mode access speed 1000 duplex full channel-group 1 mode on ! interface GigabitEthernet2/0/2 description switch_3750-1/0/2 switchport access vlan 3 switchport mode access speed 1000 duplex full channel-group 1 mode on ! interface GigabitEthernet2/0/3 ! interface GigabitEthernet2/0/4 ! interface GigabitEthernet2/0/5 ! interface GigabitEthernet2/0/6 ! interface GigabitEthernet2/0/7 ! interface GigabitEthernet2/0/8 ! interface GigabitEthernet2/0/9 ! interface GigabitEthernet2/0/10 ! interface GigabitEthernet2/0/11 ! interface GigabitEthernet2/0/12 ! interface GigabitEthernet2/0/13 ! interface GigabitEthernet2/0/14 ! interface GigabitEthernet2/0/15 ! interface GigabitEthernet2/0/16 ! interface GigabitEthernet2/0/17 ! interface GigabitEthernet2/0/18 ! interface GigabitEthernet2/0/19 ! interface GigabitEthernet2/0/20 ! interface GigabitEthernet2/0/21 description vmco 1 nic 2 switchport access vlan 103 switchport mode access speed 1000 duplex full ! interface GigabitEthernet2/0/22 description vmco 2 nic 2 switchport access vlan 103 switchport mode access speed 1000 duplex full ! interface GigabitEthernet2/0/23 description westek nic 2 switchport access vlan 103 switchport mode access speed 1000 duplex full ! interface GigabitEthernet2/0/24 description westek nic 4 switchport access vlan 103 switchport mode access speed 1000 duplex full ! interface GigabitEthernet2/0/25 ! interface GigabitEthernet2/0/26 ! interface GigabitEthernet2/0/27 ! interface GigabitEthernet2/0/28 ! interface Vlan1 no ip address shutdown ! interface Vlan3 ip address 10.3.1.4 255.255.0.0 ! ip default-gateway 10.3.1.2 ip http server ip http secure-server ip sla enable reaction-alerts ! ! ! end what should i do to get rid of the macflap errors?
... View more
Labels:
08-03-2010
06:31 AM
i have tried both crossover and straight thru cable, makes no difference also removed the spanning-tree portfast and spanning-tree bpduguard enable from the interface but does not make a difference no lights come on on either end and the interfaces remain down.
... View more
08-03-2010
06:19 AM
hi thanks for the link i have done some reading on this (chapter 35 for 3750 and 37 for 2960) and found some interesting insights and configured the switches and connected them but nothing happens at all, the interfaces stay down (line as well) i have pasted the relevant config of both the 3750 and the 2960 switch and perhaps you can see the obvious thing i am doing wrong here 3750 config no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! interface Port-channel1 ! interface GigabitEthernet1/0/1 description switch_2960-1/0/1 switchport access vlan 3 switchport mode access speed 1000 duplex full channel-group 1 mode on spanning-tree portfast spanning-tree bpduguard enable ! interface GigabitEthernet1/0/2 description switch_2960-2/0/2 switchport access vlan 3 switchport mode access speed 1000 duplex full channel-group 1 mode on spanning-tree portfast spanning-tree bpduguard enable interface GigabitEthernet2/0/1 description switch_2960-2/0/1 switchport access vlan 3 switchport mode access speed 1000 duplex full channel-group 1 mode on spanning-tree portfast spanning-tree bpduguard enable ! interface GigabitEthernet2/0/2 description switch_2960-1/0/2 switchport access vlan 3 switchport mode access speed 1000 duplex full channel-group 1 mode on spanning-tree portfast spanning-tree bpduguard enable ! interface Vlan1 no ip address shutdown ! interface Vlan3 ip address 10.3.1.3 255.255.0.0 ip broadcast-address 10.3.255.255 ! ip classless ip route 0.0.0.0 0.0.0.0 10.3.1.1 ip http server ip http secure-server ! ! control-plane ! 2960 config ! interface GigabitEthernet1/0/1 description switch_3750-1/0/1 switchport access vlan 3 switchport mode access speed 1000 duplex full channel-group 1 mode on ! interface GigabitEthernet1/0/2 description switch_3750-2/0/2 switchport access vlan 3 switchport mode access speed 1000 duplex full channel-group 1 mode on ! interface GigabitEthernet2/0/1 description switch_3750-2/0/1 switchport access vlan 3 switchport mode access speed 1000 duplex full channel-group 1 mode on ! interface GigabitEthernet2/0/2 description switch_3750-1/0/2 switchport access vlan 3 switchport mode access speed 1000 duplex full channel-group 1 mode on ! interface Vlan1 no ip address shutdown ! interface Vlan3 ip address 10.3.1.4 255.255.0.0 ! ip default-gateway 10.3.1.2 ip http server ip http secure-server ip sla enable reaction-alerts i went for the channel-group mode on as this seems to be the easiest to configure (as long as you make sure it is in the same vlan, speed, duplex etc) which i think it is, the only difference i can see is the 3750 has this configured on the ports spanning-tree portfast spanning-tree bpduguard enable and the 2960 hasn't. the consultants that came in when installing the 3750 configurd all the ports with this when i connect the 2 switch stacks via the ehterchannel ports no lights come on the switch at all (using a straight thru cable btw but also tried crossover) but nothing happens when i do a show interfaces gigabitEthernet 1/0/1 on the 3750 i get the following: GigabitEthernet1/0/1 is down, line protocol is down (notconnect) Hardware is Gigabit Ethernet, address is 0023.5d83.be81 (bia 0023.5d83.be81) Description: switch_2960-1/0/1 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX Media-type configured as connector input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 5w1d, output 3w4d, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 7997664 packets input, 2176348526 bytes, 0 no buffer Received 47574 broadcasts (0 multicasts) 0 runts, 1 giants, 0 throttles 1 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 26538 multicast, 0 pause input 0 input packets with dribble condition detected 28174176 packets output, 33210654757 bytes, 0 underruns 0 output errors, 0 collisions, 4 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out and this is the output from the 2960 show interfaces gigabitEthernet 1/0/1 GigabitEthernet1/0/1 is down, line protocol is down (notconnect) Hardware is Gigabit Ethernet, address is 1c17.d3f4.8f81 (bia 1c17.d3f4.8f81) Description: switch_3750-1/0/1 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 1w0d, output 1w0d, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 770 packets input, 85015 bytes, 0 no buffer Received 98 broadcasts (29 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 29 multicast, 0 pause input 0 input packets with dribble condition detected 893 packets output, 556254 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out is there anything obvious i am doing wrong here? many thanks
... View more
07-27-2010
07:22 AM
hi i have 1 stack of 4x 3750 switches with a data and voip vlan (vlan3 and vlan 33) i recently purchased 2x 2960s switches which are stacked and have 2 vlans (vlan3 and vlan103) vlan 103 is for iscsi/san storage I would like to connect ports 1/0/1 and 2/0/1 (vlan3) of the 2960s switches to port 1/0/1 and 2/0/1 of the 3750 stack (just to clarify i do not want to stack these together but just connect them using an ethernet cable and by connecting 2 cables have a redundant setup) i only want vlan3 traffic to go between the 3750 and 2960 switches and none of the other vlans how do i configure each of the ports on the 2960s and the 3750 to make this work. i have read the 2960s admin guide but i could not figure this out many thanks for your help cheers
... View more
Labels:
Created by
rogierboeken
in Switching
in Switching
07-23-2010
03:02 AM
07-23-2010
03:02 AM
Hi i just installed 2x cisco C2960S-24TS-L (LAN Base Switch) and configured as a stack when i detect this with CNA5.5 it tells me that it is an unsupported device. i find this very odd as the documentation and all the download links point to CNA 5.5 regards
... View more
Created by
rogierboeken
in IP Telephony and Phones
in IP Telephony and Phones
10-09-2009
03:25 AM
10-09-2009
03:25 AM
finally figured this out basically when i have the ip communicator running with video advantage i can only make internal calls and when i turn of the video unified advantage component i can make out bound calls again this kind of makes sense as we only have video calls configured internally. i do however have 1 slight problem still, when i call a 3rd party and disconnect the call the other party does not hear that i have disconnected and if the other party disconnects first my line remains connected so it seems that disconnecting a call needs to happen on both ends otherwise the call remains up. this is a minor but annoying issue as people will not know if the call got disconnected or not and in case of a network problem they will not find out immediately but only after saying are you there a thousand times and then disconnecting.
... View more
Created by
rogierboeken
in IP Telephony and Phones
in IP Telephony and Phones
10-09-2009
03:25 AM
10-09-2009
03:25 AM
finally figured this out basically when i have the ip communicator running with video advantage i can only make internal calls and when i turn of the video unified advantage component i can make out bound calls again this kind of makes sense as we only have video calls configured internally. i do however have 1 slight problem still, when i call a 3rd party and disconnect the call the other party does not hear that i have disconnected and if the other party disconnects first my line remains connected so it seems that disconnecting a call needs to happen on both ends otherwise the call remains up. this is a minor but annoying issue as people will not know if the call got disconnected or not and in case of a network problem they will not find out immediately but only after saying are you there a thousand times and then disconnecting.
... View more
Created by
rogierboeken
in Other Wireless - Mobility Subjects
in Other Wireless - Mobility Subjects
10-05-2009
02:21 AM
10-05-2009
02:21 AM
so disabled the lower rates (1,2,5.5 and 6) and all was well for 5 days and then all of a sudden this laptop and another laptop started to roam from 1 AP to another, they did this about 3 to 4 times over a 24 hour period and then it could not longer reconnect. i have now also disabled the 9mb to see if that reduces the range even further. the user is currently travelling and will not be able to reconnect the laptop for 2 weeks now which is a shame, so i cannot do any furhter updates for a couple of weeks
... View more
Created by
rogierboeken
in Other Wireless - Mobility Subjects
in Other Wireless - Mobility Subjects
09-25-2009
09:04 AM
09-25-2009
09:04 AM
i will disable those data rates first and see how it goes i am using lenovo think vantage access manager (i use it on all my client devices) cheers
... View more
Created by
rogierboeken
in Other Wireless - Mobility Subjects
in Other Wireless - Mobility Subjects
09-25-2009
08:17 AM
09-25-2009
08:17 AM
hi i have setup a wireless network (hidden ssid, wpa2-aes, G radio only) by using 5 1131AG AP as root devices (all connected to the same switch all stationary clients or roaming clients (iphones, blackberries etc) all roam seamlessly from 1 AP to another i have one laptop which does not move from its location and sits right next to an AP wiht full strenght signal which for some reason once in a while roams to another AP which is quite far away and the signal drops a lot and it often disconnects and does not want to reconnect to the original AP it was connected to. all 1131 are running 12.4(10b)JDA this particular client that has the problem has an Intel(R) WiFi Link 5300 AGN with the latest drivers i have disabled all power savings etc on this client and when it is on a network with just 1 AP (our office) it stays connected for days on end. so something causes this client to decided to roam from 1 AP to another and then completely disconnects because of the low signal strength I am thinking about broadcasting the SSId on the accesspoint it is sitting right next to (this is in a rural area with no neighbours for miles) so broadcasting the SSId from 1 AP is not going to cause a problem. or could something else prevent this client from roaming (also tried setting preferred AP on the client but does not help either) client has latest drivers for that particular wireless card many thanks
... View more
01-25-2016
hi we are just finishing an upgrading from CUCM 8.6.4 and CUPS (8.6.5)
and CUC 8.6 to CUCM/CUPS/CUC ...
Created by
rogierboeken
in Wireless and Mobility
01-13-2014
01-13-2014
i had not thought about disabling the lowerrates on the AP and have done
that but it still went out ...
01-06-2014
i have exactly same setup (2008 r2 enterprise CA and cups 8.6.4_ and
used webserver template just li...
11-12-2013
my cisco integrator (insight in the UK) emailed me this and having
checked all these settings i noti...
11-11-2013
when i run show web-security i get thisadmin: show web-security[
Version: V3 Serial Number: 44199171...
Created by
rogierboeken
in Collaboration Applications
11-06-2013
11-06-2013
btw i had a problem where some users showed up with their IM name and
others with their nicknamei fo...
11-06-2013
i am facing similar problemyou cannot deploy it via GPO as it puts it a)
in the computer certificate...
11-06-2013
i replaced all the self signed certificates and replaced them with
enterprise CA signed certificates...
10-28-2013
i created the SSL certificate for the cucm-pub and sub and restarted the
tomcat servicewhen the jabb...
10-28-2013
thanks for all the responsei had to create the certificate using the cli
on my windows CA certreq -s...
10-16-2013
so i have my own windows enterprise CA on windows 2008 r2 server and i
thought i would submit the CS...
10-16-2013
hiin order to placate my jabber 9.2.5 clients (which prompts users to
trust the unity connection tom...
10-14-2013
is there is a clever way to get these standard cisco certificates
trusted on all my computers rather...
10-10-2013
hii have just upgraded some of my cisco jabber for windows clients to
the latest release 9.2.6 (upgr...
Created by
rogierboeken
in Unified Communications Infrastructure
09-23-2013
09-23-2013
hiwe have an UK and USA officeboth offices have their own seperate
CUCM/CUPS installation (version 8...
Public Statistics
| Date Registered | 01-17-2007 09:08 AM |
| Date Last Visited | 10-19-2017 12:23 PM |
| Total Messages Posted | 87 |
| Total Helpful Votes Received | 10 |
