Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About glen.grant
09-25-2018
glen.grant
Member since
12-19-2001
Advisor
05-15-2018
11:40 AM
If your connections between the switches are routed links then STP is irrelevant and is not run on those links .
... View more
01-16-2017
11:49 AM
normally there is no special requirements needed to download a K9 file .
... View more
11-03-2016
10:27 AM
If you can get in do a show users and see if there are any sessions hung and if so clear them otherwise to clear this issue you will probably have to reload the switch to free up resources .
... View more
11-03-2016
10:20 AM
Port 11 is setup as a trunk , change it to an access port in vlan 11 and set your DG as 3.254 on your client and retry your ping tests . Its not going to ping right if the port is set as a trunk .
... View more
06-23-2016
10:44 AM
sounds like you do not have 4 good pairs of wires . You must have 4 good pairs in order for gigabit to run , whereas for 100 you only need 2 good pairs . And you are sure that the nics are gigabit nics in the pc's ?
... View more
06-20-2016
10:53 AM
If you do a "show vlan id <vlan number> . This will show you all ports including any trunk ports that the vlan is assigned to.
... View more
06-14-2016
09:05 AM
there isn't a "shutdown" line command in the "startup" config is there ? This would shut them down each time switch is rebooted . Check startup config .
... View more
06-01-2016
12:16 PM
If you just trunked the vlan to the 4948 then a static route should not have been needed as the default gateway is on the 3750 . Any ip address on the 4948 would have been just to manage the switch and the ip default gateway command could have been used .
... View more
05-27-2016
07:58 AM
If doing router on a stick and the 2800 is doing the routing then yes each subinterface needs an ip address on and all devices in that vlan would use that address as their default gateway off the subnet .
... View more
05-26-2016
08:13 AM
Network connectivity is always going to be strange when you have devices within the same address range but they are using different subnet masks . This is a no no and will lead to unpredictable results .
... View more
05-26-2016
08:07 AM
Unless you have spare box to test it on you don't really know. I have never seen the smaller boxes like you are stating take more than say 5-8 minutes to completely boot up . Even bigger boxes like the 6509's should not take more than say 12 minutes or so . You had something else going on if it took 30-40 minutes for the switch to be reachable again . If you have big stacks of 3750's say 8 switches in a stack then it will take somewhat longer .
... View more
05-25-2016
11:24 AM
2950 does not have auto mdix so make sure if you are going other switches you use a crossover . if the connection to the isp is 100 meg set the port as auto , ISP not likely to have hardcoded the port and this will cause a duplex mismatch . If you have all your ports in the same vlAN then that should be functionally equivalent to a linksys switch without mdix capabilty . Unless you have a specific reason you shouldn't need any ports trunked .
... View more
05-25-2016
10:59 AM
Read this for upgrade instructions and requirements. http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5500/sw/upgrade/708_N1_1/n5500_upgrade_downgrade_700.html
... View more
05-24-2016
09:57 AM
No it should work. One end should be auto and the other dynamic or both ends should be dynamic . Maybe post your config.
... View more
05-15-2018 11:40 AM
If your connections between the switches are routed links then STP is
irrelevant and is not run on t...
11-03-2016 10:27 AM
If you can get in do a show users and see if there are any sessions hung
and if so clear them otherw...
11-03-2016 10:20 AM
Port 11 is setup as a trunk , change it to an access port in vlan 11 and
set your DG as 3.254 on you...
06-23-2016 10:44 AM
sounds like you do not have 4 good pairs of wires . You must have 4 good
pairs in order for gigabit ...
06-20-2016 10:53 AM
If you do a "show vlan id . This will show you all ports
including any trunk ports that the vlan is...
06-14-2016 09:05 AM
there isn't a "shutdown" line command in the "startup" config is there ?
This would shut them down e...
06-01-2016 12:16 PM
If you just trunked the vlan to the 4948 then a static route should not
have been needed as the defa...
05-27-2016 07:58 AM
If doing router on a stick and the 2800 is doing the routing then yes
each subinterface needs an ip ...
05-26-2016 08:13 AM
Network connectivity is always going to be strange when you have devices
within the same address ran...
05-26-2016 08:07 AM
Unless you have spare box to test it on you don't really know. I have
never seen the smaller boxes l...
05-25-2016 11:24 AM
2950 does not have auto mdix so make sure if you are going other
switches you use a crossover . if t...
05-25-2016 10:59 AM
Read this for upgrade instructions and requirements.
http://www.cisco.com/c/en/us/td/docs/switches/d...
Public Statistics
| Date Registered | 12-19-2001 05:02 PM |
| Date Last Visited | 09-25-2018 10:51 AM |
| Total Messages Posted | 6,567 |
| Total Helpful Votes Received | 2766 |
Helpful Votes Given To
| User | Helpful Count |
|---|---|
| 5 | |
| 5 | |
| 5 | |
| 5 | |
| 3 |
.jpg "Hall of Fame Master"){kind=icon}
.jpg "VIP Expert"){kind=icon}
Helpful Votes From
| User | Helpful Count |
|---|---|
| 5 | |
| 5 | |
| 5 | |
| 5 | |
| 5 |
Awards
Cisco Designated VIPs
2011 LAN
