Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Hamza Al-Qudah
Stats
Member since
11-25-2012
22
Posts
0
Helpful
0
Solutions
Created by
Hamza Al-Qudah
in Firewalls
in Firewalls
09-17-2013
12:23 AM
09-17-2013
12:23 AM
Dears I recive this message in my fwsm when I try to connect to a SQL server %FWSM-6-106028: Deny TCP (Connection marked for Deletion) from 10.110.12.11/61245 to 10.110.80.12/1433 flags SYN on interface outside_SAPCRM I read about th is error and i increased the half open timeout ..but the same issue happens kindly your support
... View more
Labels:
07-01-2013
01:13 PM
Dears , I wannt to recover the enable pasword of the FWSM is this the correct procedure : Router# hw-module module slot-number reset cf:1 Router# session slot slot-number processor 1 Log into Root. root@localhost# clear passwd cf:partition_number root@localhost# exit and if this true , it will reboot FWSM from maintenance partition which is cf:1 , is this will affect the traffic ? I think it will
... View more
Labels:
01-14-2013
06:24 AM
Dears, Whats is the cisco support types and the differences between them ( smartnet , shared support ...etc)
... View more
Labels:
12-10-2012
06:46 AM
yes mahmood but I faced it when I issued the command copy run start in a vdc ....the follwoing message appeared : Configuration update aborted: This vdc has had a global configuration change since the last saved config. Please save config in default vdc before proceeding and when i issed the copying in the global vdc then on this vdc ...it saved
... View more
12-10-2012
06:43 AM
mahmood thanx my freind but ip route will used if u are using the sw as L3 , I will use it as just L2
... View more
12-10-2012
02:27 AM
Thanx for ur reply ok , but regarding to nexus switches , there is no ip default gateway command ...so what is the alternative command other than configuring it by the dialoge
... View more
12-10-2012
02:09 AM
dears kindly why the nexus 2k has 8 uplink ports ???? My opinion and plz correct me ..... thats because the nexus 7k or 5k can be devided into 4 virtual devices ( using vdc) and making 8 uplink ports in the 2k will allow us to use the extender for all the 4 vdc's with 2 uplinks ( for redundancy ) from each vdc
... View more
Labels:
Created by
Hamza Al-Qudah
in Switching
in Switching
12-10-2012
02:05 AM
12-10-2012
02:05 AM
thanx for ur reply
... View more
12-10-2012
02:04 AM
Dears kindly we know that the ip default gateway is used for L2 switch now if we have a layer 2 switch with ip default gateway and we activated layer 3 functionality on it , and configured a defualt route like this : ip default gateway x.x.x.x ip route y.y.y.y so which one will take more priority ??????? my opinion and plz correct me : the L3 port will use the routing table but the L2 ports will still use the ip default gateway ..... traffic in L3 port will be checked by the cef ( adjacency table ) and if it doesnt find the destination it will use the routing tabel wher the default route is installed traffic in L2 port will be checked by the arp table and if it doesnt find the destination it will use the default gateway .
... View more
Labels:
12-10-2012
01:43 AM
dears plz correct me : When I make copy run start in the default vdc it will effect the changes of that vdc and of the aresources allocations ( interfaces ..memory ...etc ) but when u make copy run start on another vdc it will effect the configration of this vdc only ...
... View more
Labels:
Created by
Hamza Al-Qudah
in Switching
in Switching
12-09-2012
03:00 PM
12-09-2012
03:00 PM
Dears, regarding to the out of band Management interface , if I configured an intervace vlan to be as a managment interface for one vdc ( the default vdc ) , when I connected to this vdc via telnet , can I switch to any other vdc ? ( suppose that I have the Admin role which allows me to enter and config all the vdc's ) If that is possible so that I dont have to make a dedicated managment ip for each VDC I need to do that only if I want to make vdc admin's account to allow some users to access specific vlans only , is that true ?
... View more
Labels:
09-17-2013
Dears I recive this message in my fwsm when I try to connect to a SQL
server %FWSM-6-106028: Deny TC...
07-01-2013
Dears ,I wannt to recover the enable pasword of the FWSMis this the
correct procedure :Router# hw-mo...
01-14-2013
Dears,Whats is the cisco support types and the differences between them
( smartnet , shared support ...
12-10-2012
yes mahmood but I faced it when I issued the command copy run start in a
vdc ....the follwoing messa...
12-10-2012
mahmood thanx my freindbut ip route will used if u are using the sw as
L3 , I will use it as just L2
Created by
Hamza Al-Qudah
in Data Center Switches
12-10-2012
12-10-2012
dearkindly what is the diference between configuring the managment
interface of the nexus switch wit...
12-10-2012
Thanx for ur replyok , but regarding to nexus switches , there is no ip
default gateway command ...s...
12-10-2012
dearskindly why the nexus 2k has 8 uplink ports ????My opinion and plz
correct me ..... thats becaus...
12-10-2012
Dears kindly we know that the ip default gateway is used for L2
switchnow if we have a layer 2 switc...
12-10-2012
dears plz correct me :When I make copy run start in the default vdc it
will effect the changes of th...
Public Statistics
| Date Registered | 11-25-2012 09:05 PM |
| Date Last Visited | 05-30-2018 01:22 PM |
| Total Messages Posted | 22 |
