I have a ISR 4331. I've just upgraded the IOS to isr4300-universalk9.03.17.03.S.156-1.S3-std.SPA.bin. I've added a WIC card: vwic3-2mft-t1/e1. I'used the command: card type t1 0 1 and after a restart, the controller configuration was populated:  controller T1 0/1/0 framing esf linecode b8zs cablelength long 0db ! controller T1 0/1/1 framing esf linecode b8zs cablelength long 0db !   When I try to add\configure serial interfaces, I'm not able to. There's no serial interfaces showing in the inventory:   SH Inventory: RT09-4331-01#sh inventory NAME: "Chassis", DESCR: "Cisco ISR4331 Chassis" PID: ISR4331/K9 , VID: V03, SN: FLM2114W149 NAME: "Power Supply Module 0", DESCR: "250W AC Power Supply for Cisco ISR 4330" PID: PWR-4330-AC , VID: V02, SN: DCA211010V4 NAME: "Fan Tray", DESCR: "Cisco ISR4330 Fan Assembly" PID: ACS-4330-FANASSY , VID: , SN: NAME: "module 0", DESCR: "Cisco ISR4331 Built-In NIM controller" PID: ISR4331/K9 , VID: , SN: NAME: "NIM subslot 0/1", DESCR: "NIM-2MFT-T1/E1 - T1/E1 Serial Module" PID: NIM-2MFT-T1/E1 , VID: V02, SN: FOC19192STE NAME: "NIM subslot 0/0", DESCR: "Front Panel 3 ports Gigabitethernet Module" PID: ISR4331-3x1GE , VID: V01, SN: JAB092709EL NAME: "module 1", DESCR: "Cisco ISR4331 Built-In SM controller" PID: ISR4331/K9 , VID: , SN: NAME: "module R0", DESCR: "Cisco ISR4331 Route Processor" PID: ISR4331/K9 , VID: V03, SN: FDO210812QW NAME: "module F0", DESCR: "Cisco ISR4331 Forwarding Processor" PID: ISR4331/K9 , VID: , SN:   ------------------------------------------------------------------------------ SH Running Version: RT09-4331-01#sh ver Cisco IOS XE Software, Version 03.16.04b.S - Extended Support Release Cisco IOS Software, ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5(3)S4b, RELEASE SOFTWARE (fc1) Technical Support:   http://www.cisco.com/techsupport Copyright (c) 1986-2016 by Cisco Systems, Inc. Compiled Mon 17-Oct-16 20:23 by mcpre Cisco IOS-XE software, Copyright (c) 2005-2016 by cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software. ROM: IOS-XE ROMMON RT09-4331-01 uptime is 22 minutes Uptime for this control processor is 24 minutes System returned to ROM by reload at 01:13:46 UTC Fri Apr 7 2017 System image file is "bootflash:/isr4300-universalk9.03.16.04b.S.155-3.S4b-ext.SPA.bi" Last reload reason: PowerOn   This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com.   Suite License Information for Module:'esg' -------------------------------------------------------------------------------- Suite Suite Current Type Suite Next reboot   -------------------------------------------------------------------------------- FoundationSuiteK9 None None None   securityk9 appxk9 AdvUCSuiteK9 None None None   uck9 cme-srst cube Technology Package License Information: ----------------------------------------------------------------- Technology Technology-package Technology-package Current Type Next reboot ------------------------------------------------------------------ appxk9 None None None uck9 None None None securityk9 None None None ipbase ipbasek9 Permanent ipbasek9 cisco ISR4331/K9 (1RU) processor with 1648789K/6147K bytes of memory. Processor board ID FLM2114W149 3 Gigabit Ethernet interfaces 2 Channelized T1/PRI ports 32768K bytes of non-volatile configuration memory. 4194304K bytes of physical memory. 3125247K bytes of flash memory at bootflash:. Configuration register is 0x2102 RT09-4331-01#   Any thoughts?   Thanks, Chris ... View more

Greetings, I have a Cisco ISR 4331 that I'm configuring to replace an older router. I'm adding a 2MFT-T1/E1 card into the first 'slot', which appears to be labeled NIM 1. Typically, I've added a card by typing......   card type t1 0 1   .....which, ironically, is what I see to add when i boot the router and look at the current config. When I type this command, I get the message 'Card not present'.   Any thoughts would be appreciated. Chris   ... View more

Greetings, I have a 2911 router that I'm trying to configure SNMP on, but having problems with one command: snmp-server enable traps voice poor-qov. I'm thinking that maybe the command has changed or isn't supported, but haven't found anything specific in my research yet. The version of IOS is: Version 15.0(1r)M16. Thanks for any thoughts, Chris ... View more

We've purchased a 2911 router and a vwic3-2mft-t1/e1. I've inserted the card and configured card type, but my experience with these cards is that after adding a card, it should add serial interfaces. I'm obviously missing something. What I'm trying to do is to configure multilink for a bonded T1. Any help would be appreciated. Chris ... View more

I'm on location where we had two Cisco Catalyst switches -- a 24-port 3650 and a 48 port 3650. The 24--port was installed months ago, then we quickly outgrew it and added the 48-port with the understanding we'd remove teh 24-port at some point. Tonight is that night. The 24 port was configured as the VTP server and had the default vlan plus two other vlans, one for data, one for voice. Easy enough. I migrated the cables, changed configuration for the ports as appropriate and everything seemed to be fine. I removed the original switch was able to test connectivity with no errors. Then I powered the device off, so I could remove the original switch, move this switch up closeer to the patch panel, etc. Powered it on and no clients can get out. IPCONFIG on a windows 7 machine and it shows that the cable is disconnected. I had changed the VTP info on the 48 port switch (in case that made a difference), I've gone through the switch configuration until I'm blind. It's like the clients can't connect to the network, or can't see the data vlan.  I've attached the switch configuration. ... View more

Greetings,   I have a new Cisco 2911 router that I need to install and configure a vwic3 card in. I'm not so concerned about running voice. I will be replacing an existing router into a circuit that will be running a bonded T1. I discovered the link below and have some questions.   3. The card is installed in the first available slot, which happens to be 0. So I entered: card type t1 0. Would that be correct? 4. The next step is voice-card slot. I'm assuming that I'd configure the same.. voice-cad 0. 5. Next, codec complexity { flex [ reservation-fixed { high | medium }] | high | medium }. I'm not familiar with this statement. Essentially, we use CoS to 'filter' or manage our traffic. Recommendations? 6. Next, controller {e1 | t1} slot / port  - I would assume as above 0/0 7. framing {sf | esf} or {crc4 | no-crc4} 8. linecode {ami | b8zs} or  {ami | hdb3} 9. clock source (?) 10. (??) 11.voice-port (?) 12. Exit   Pretty lost with some of this stuff....I'm researching this some more, but if anyone can clear up my confusion, I'd appreciate it.   Configuring Voice and Data on 1-Port and 2-Port T1/E1 VWIC3 - Cisco   SUMMARY STEPS     1. enable 2. configure terminal 3. card type {e1 | t1} slot subslot 4. voice-card slot 5. codec complexity { flex [ reservation-fixed { high | medium }] | high | medium } 6. controller {e1 | t1} slot / port 7. framing {sf | esf} or framing {crc4 | no-crc4} 8. linecode {ami | b8zs} or linecode { ami | hdb3 } 9. clock source {line [primary | bits | independent] | internal [independent] | free-running } 10. ds0-group ds0-group-number timeslots timeslot-list type { e&m-delay-dial | e&m-fgd | e&m-immediate-start | e&m-wink-start | ext-sig | fgd-eana | fxo-ground-start | fxo-loop-start | fxs-ground-start | fxs-loop-start } or pri-group [ timeslots range ] 11. voice-port { slot-number / subunit-number / port | slot / port : ds0-group-number } 12. exit ... View more

Greetings, I have a new Cisco 2911 router that I need to install and configure a vwic3 card in. I'm not so concerned about running voice. I will be replacing an existing router into a circuit that will be running a bonded T1. I discovered the link below and have some questions. 3. The card is installed in the first available slot, which happens to be 0. So I entered: card type t1 0. Would that be correct? 4. The next step is voice-card slot. I'm assuming that I'd configure the same.. voice-cad 0. 5. Next, codec complexity { flex [ reservation-fixed { high | medium }] | high | medium }. I'm not familiar with this statement. Essentially, we use CoS to 'filter' or manage our traffic. Recommendations? 6. Next, controller {e1 | t1} slot / port  - I would assume as above 0/0 7. framing {sf | esf} or {crc4 | no-crc4} 8. linecode {ami | b8zs} or  {ami | hdb3} 9. clock source (?) 10. (??) 11.voice-port (?) 12. Exit Pretty lost with some of this stuff....I'm researching this some more, but if anyone can clear up my confusion, I'd appreciate it. Configuring Voice and Data on 1-Port and 2-Port T1/E1 VWIC3 - Cisco SUMMARY STEPS 1. enable 2. configure terminal 3. card type {e1 | t1} slot subslot 4. voice-card slot 5. codec complexity { flex [ reservation-fixed { high | medium }] | high | medium } 6. controller {e1 | t1} slot / port 7. framing {sf | esf} or framing {crc4 | no-crc4} 8. linecode {ami | b8zs} or linecode { ami | hdb3 } 9. clock source {line [primary | bits | independent] | internal [independent] | free-running } 10. ds0-group ds0-group-number timeslots timeslot-list type { e&m-delay-dial | e&m-fgd | e&m-immediate-start | e&m-wink-start | ext-sig | fgd-eana | fxo-ground-start | fxo-loop-start | fxs-ground-start | fxs-loop-start } or pri-group [ timeslots range ] 11. voice-port { slot-number / subunit-number / port | slot / port : ds0-group-number } 12. exit ... View more