About pille1234

pille1234 · ‎07-27-2019

Hi! Do you have "Graceful Maintenace" enabled for the leaf maintenace group by chance? Regards

pille1234 · ‎01-16-2019

Hi Remi Astruc, thank you, somehow I missed that option. It's a pitty though that I have to remove the virtual domain and reapply it to change these settings. Anyway, it is the option I was looking for. Best regards

pille1234 · ‎01-16-2019

G'day everyone, I am trying to allow a vmware virtual machine to send frames with a "forged" MAC address. By forged I mean a MAC address that is not supplied by Vcenter, like you would need for a bond interface. I have seen this option for trunk port groups, however a trunk port group is not what I am looking for. In classic vmware I would simpliy allow this within the specific port group configuration in VCenter, but I can't find such a configuration in ACI. Any ideas? Best regards

pille1234 · ‎11-18-2018

It does work with CSR1kv as well, but I don't know if this is a supported design for a production environment.

pille1234 · ‎11-16-2018

Hi, I am doing AVS with vxlan, so there is no vlan encap I could use. But let's assume I'd use classic Vmware DVS I could select a dedicated VLAN/Portgroup for the router vm, but what next?

pille1234 · ‎11-11-2018

Hallo, is it that nobody knows how to do this or is it unclear what I am asking? Regards

pille1234 · ‎11-06-2018

Hallo, I am a blockhead right now in terms of how to integrate a virtual router into aci. I know how to attach physical firewalls with a L3out, however I don't know how to do this with virtual machines. We have an ESX-environment with AVS (soon AVE) in VXLAN-Mode where I'd like to have virtual machines take over a routing function (Loadbalancer, vASA, VPN-Router). If I create a L3out I need to configure a static path that is related to a physical switchport with a vlan encap, which doesnt't make sense in this environment. Is there any other way? Would it be different if we had Vmware-Integration in classic vlan mode? I imagine I could use the same VLAN-ID for L3out like I used for the EPG of the Router-VM, but I suppose this would raise a fault, like "encap already in use" or something like that. Is there any document covering my Usecase? Best regards Pille

pille1234 · ‎12-17-2017

Hallo, I am trying to configure MP-BGP EVPN (Golf) with ACI and ASR 9k in a lab setup. I do have a working multipod environment. The thing I am struggling with right now is the bgp ASN I have to use for GOLF. I configured MP-BGP within the fabric with ASN 65500 to keep it separate from the ASN on the WAN-Device (65010), however that may not have been the smartest idea. Now I am trying to bring up the MP-BGP connection between ACI Spines and WAN-device but that fails, because I configured the ACI-Neighbor to be part of ASN 65010 to bring up an iBGP-Peering, but ACI considers itself to be ASN 65500. Is there any way out or do I have to use the same ASN within the fabric as outside or should I consider to configure an eBGP-Peering? Is there any best practice for this seup? To use MP-BGP with eBGP looks somehow "unusual" and does not feel right to me. Any ideas welcome. Best regards Pille

pille1234 · ‎05-13-2016

Hallo, I opened a TAC Case and they confirmed that I had to remove the license first: Backup: copy license bootflash:license.tar Delete: clear license <filename> clear license sprom (hidden command) Depending on the configuration you may need to reload the switch for it to take effect. Regards Pille

pille1234 · ‎02-09-2016

That really depends on your exact use case. Out of my head I could think of several different aproaches to your request: Link-State-Tracking feature for Catalyst and Nexus 4000 - you could easily bring down a downlink port, when the corresponding uplink went down: Cisco Config Guide Are your bound interfaces Port-channels? Then use the lacp min-link-feature do bring the channel down Do the physical interfaces need to go down or could route-manipulation help as well? Then use IP SLA and line protocol tracks. Two separate tracks could be connected with an AND-statement, allowing the track do go down once the first link is gone As already mentioned: use EEM. Not as difficult as you might think: track 1 interface e1/1 line-proto event manager applet BRING-IF2-DOWN event track 1 state down action 1.0 cli command "conf t" action 2.0 cli command "int e1/2" action 3.0 cli command "shut" same is needed for the other interface. Hope that helps, best regards

pille1234 · ‎01-11-2016

Hi Eddie, that's what I figured out, yet I'd like to know how to actually use this port. Is there any way to set up an IP-address?

pille1234 · ‎01-10-2016

Hallo everyone, I'm just getting familiar with our new ASR 9904 devices. I'm wondering how to setup the onboard CMP interfaces on the RSPs. Coming from N7k, I expect these ports to be connected to some kind of integrated terminal server module. The little documentation I could find within ASR System Management Configuration Guide is terrible meaningless, not giving any hint on how to set it up. Could anyone give me some input or point me to a more toroughly documentation? Best regards

pille1234 · ‎08-14-2015

Hi Reza, thanks for your reply. Right now there's no server attached to these switches, but we bought 14 of them and before we can put them into production we need to prove their abillity to do ISSU. Guess I have to open a TAC case to get a solution. Regards Pille

pille1234 · ‎08-13-2015

Hallo, I was about to update a pair of new Nexus 5572UP Switches, but switch told me that ISSU with L3 features were not supported. However I don't have a layer 3 daughter card installed and use the switches as pure layer 2 access switches with vpc configuration. After a little googlefu I realized that -for whatever reason- I had a L3 license (LAN_BASE_SERVICES_PKG) installed that could cause the problem. Next step was to remove the license (why was it preinstalled to begin with?), but that failed, because "License is in use". show license usage LAN_BASE_SERVICES_PKG told me that "btcm" is the application in use. SWITCH# show system internal btcm info system status : L3 Ready 0 Router Card(s): Ok so what exactly is btcm and what options do I have? These switches will never do any L3 and I'd like to have the ISSU-Feature back. Any ideas? Regards Pille

pille1234 · ‎06-23-2015

Q1 Your config lacks the vpc ID. Add vpc 109 On both Nexus switches under the port channel 109 interface. Q2 You need 2 port channel, each going from ASR to both VSS switches. Regards

pille1234 · 07-27-2019

Hi! Do you have "Graceful Maintenace" enabled for the leaf maintenace group by chance? Regards

pille1234 · 06-30-2019

Hallo, I assume you use the same vpc domain ID on both sites? That results in the use of the same br...

pille1234 · 01-16-2019

Hi Remi Astruc, thank you, somehow I missed that option. It's a pitty though that I have to remove t...

pille1234 · 01-16-2019

G'day everyone, I am trying to allow a vmware virtual machine to send frames with a "forged" MAC add...

pille1234 · 11-18-2018

It does work with CSR1kv as well, but I don't know if this is a supported design for a production en...

pille1234 · 11-16-2018

Hi, I am doing AVS with vxlan, so there is no vlan encap I could use. But let's assume I'd use class...

pille1234 · 11-11-2018

Hallo, is it that nobody knows how to do this or is it unclear what I am asking? Regards

pille1234 · 11-06-2018

Hallo, I am a blockhead right now in terms of how to integrate a virtual router into aci. I know how...

pille1234 · 12-17-2017

Hallo, I am trying to configure MP-BGP EVPN (Golf) with ACI and ASR 9k in a lab setup. I do have a w...

pille1234 · 05-13-2016

Hallo, I opened a TAC Case and they confirmed that I had to remove the license first: Backup: copy l...

pille1234 · 02-09-2016

That really depends on your exact use case. Out of my head I could think of several different aproac...

pille1234 · 01-11-2016

Hi Eddie, that's what I figured out, yet I'd like to know how to actually use this port. Is there an...

pille1234 · 01-10-2016

Hallo everyone, I'm just getting familiar with our new ASR 9904 devices. I'm wondering how to setup ...

pille1234 · 08-14-2015

Hi Reza,thanks for your reply. Right now there's no server attached to these switches, but we bought...

pille1234 · 08-13-2015

Hallo,I was about to update a pair of new Nexus 5572UP Switches, but switch told me that ISSU with L...

Date Registered	‎01-10-2012 12:34 PM
Date Last Visited	‎07-31-2019 12:34 AM
Total Messages Posted	161
Total Helpful Votes Received	75

Re: L2 Bridge Domain failure during up...

Re: ACI with Vmware DVS integration: al...

ACI with Vmware DVS integration: allow ...

Re: ACI Golf Router Supported devices

Re: L3out to virtual machine with Vmwar...

Re: L3out to virtual machine with Vmwar...

L3out to virtual machine with Vmware-In...

ACI MP-BGP ASN and different GOLF EVPN ...

Hallo,

That really depends on your

Hi Eddie,

CMP Ports on ASR9904

Hi Reza,thanks for your reply

ISSU on 5672 fails due to L3 license

Q1Your config lacks the vpc

Re: L2 Bridge Domain failure during upgrade

Re: Dual Nexus 9K VPC Pair and Port-channel / SPT

Re: ACI with Vmware DVS integration: allow "Forged transmits"

ACI with Vmware DVS integration: allow "Forged transmits"