About Soushi Takata

Soushi Takata · 09-09-2025

Thank you for your reply. I am having trouble with my user VN client being unable to communicate with the DHCP server.I'm using Catalyst Center 2.3.7.9 to build SDA fabric.The DHCP server is located outside the SDA fabric and connected via FusionSW.O...

Soushi Takata · 02-01-2022

Thank you for your answer. I used the NCS55A2-MOD-SE-S and the ASR9901 to create a verification environment for the SRv6/MPLS L3 Service Interworking Gateway.NCS55-1 is SR-MPLS and NCS55-2 is Gateway and ASR9901 is SRv6.Version is 7.5.1. ------------...

Soushi Takata · 03-03-2021

Thanks for any insight. I want to move from RSVP-TE to SR-TE policy.The RSVP-TE environment uses the path protection function.I would like to use the path protection feature in the SR-TE policy environment as well.But I could not find any such featur...

Soushi Takata · 08-21-2020

Hi, Does ASR9000 and NCS5500 support IPv4 over MPLS without VPN?I'm in trouble because I can't find a clear statement in Cisco's web site.I tried with the following Config, but MPLS label was not attached and communication was performed with Pure IP....

Soushi Takata · 01-10-2019

Thanks for any insight. I want to use MPLS L3VPN over SR-TE Policy on ASR9000.So I configured SR-TE Policy on Ingress PE and configured vpnv4 route-policy on Egress PE. ---<Ingress PE> segment-routing traffic-eng segment-list AP14 index 1 mpls la...

Soushi Takata · 09-11-2025

Thank you, AndriiThank you, Jedolphi I understand that the DHCP server prefix information or Default GW information is not required on the EN RIB.And I also understand that communication with the DHCP server is done using LISP information.I will chec...

Soushi Takata · 03-06-2022

Hi Harold, Thank you for your reply. I too believe that the best solution is to have different RDs.However, there are examples where the same user uses the same RD at each location.So I don't understand the logic that RD must be a different value, bu...

Soushi Takata · 03-06-2022

Thank you for your answer. Perhaps this problem has been resolved.If the RD of the gateway router is different from the other routers(SR-MPLS's PE router and SRv6's PE router), the PE routers can receive the prefix information correctly.Here is the v...

Soushi Takata · 02-02-2022

Hi Harold, Thank you for your reply. I have changed the ISIS on the Gateway Router to Multidomain.router isis 1 is-type level-2-only net 13.1113.1113.1113.00 address-family ipv4 unicast metric-style wide router-id Loopback0 segment-routing m...

Soushi Takata · 03-04-2021

Ioris, It's this config that I wrote that I remember.However, this configuration cannot be set in the current IOS-XR.We can't specify segment-routing in the path-option setting.Now we need to configure the policy in the segment routing section. segme...

Member Since	‎08-04-2013 02:18 PM
Date Last Visited	‎11-09-2025 06:51 PM
Posts	18
Total Helpful Votes Received	6

User Statistics

User Activity

Clients cannot access DHCP servers outside the SDA fabric

SRv6/MPLS L3 Service Interworking Gateway does not work

Does SR-TE policy have a path protection function?

Does ASR9000 and NCS5500 support IPv4 over MPLS without VPN

MPLS L3VPN over SR-TE Policy

Re: Clients cannot access DHCP servers outside the SDA fabric

Re: SRv6/MPLS L3 Service Interworking Gateway does not work

Re: SRv6/MPLS L3 Service Interworking Gateway does not work

Re: SRv6/MPLS L3 Service Interworking Gateway does not work

Re: Does SR-TE policy have a path protection function?