Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About wimpog97
Stats
Member since
09-06-2013
11
Posts
0
Helpful
0
Solutions
09-25-2014
05:56 AM
Thank you for your reply. Can't I just go from 1.2.0.97 to 1.4.0.88 directly?
... View more
09-24-2014
01:27 PM
Thank you for your reply. Unfortunately, this command is not available in Global Configuration mode. Is it for a different firmware version? Here is the output of show version: Unit SW version Boot version HW version ------------------- ------------------- ------------------- ------------------- 1 1.3.0.62 1.3.0.03 V01
... View more
Created by
wimpog97
in Small Business Switches
in Small Business Switches
09-22-2014
08:42 AM
09-22-2014
08:42 AM
Is there a way to do switchport port-security violation {protect | restrict | shutdown} in SG-500-28P in case of a BPDU Guard violation? Seems like the default option is shutdown and I don't know how to change it. Thank you!
... View more
- Tags:
- sg-500
Labels:
09-09-2013
08:55 AM
Thanks Tom, I'll give it a try. I think, all I need to do is dedicate a few ports to another VLAN and plug the devices to them. That'll give me a separate logical switch, right?
... View more
09-09-2013
08:19 AM
Hi Tom, What if I just want to put a few ports into its own VLAN so they can act as a separate switch connected to a separate router interface, what do I need for that? No inter-VLAN routing is needed. The switch should limit its traffic only to these ports, right, unless I have a trunk port? I don't think I need to configure sub-interface or stuff like that, but I believe I do need to enable tagging. I basically have another line used for testing that has a separate 5-port switch that I want to get rid of. Thanks!
... View more
09-09-2013
08:01 AM
Hi Tom, In L3 Vlans is tagging nedded at all? Or is it there just for backwards-compatibility with L2 switches? I would assume an L3 switch should be able to limit/differentiate the traffic by IP addresses. I definitely need to start learning about L3 switches. Thanks!
... View more
09-09-2013
07:08 AM
Thanks Tom. Could you please tell me what functionality appears/disappears in general once L3 is enabled? I know very little about L3 switches. I'd have to learn more about them. I guess I'll stick to L2 VLAN functionality for now. I don't see any problem with that, do you? The switch supports dot1q tagging, doesn't it? Does it tag the frames if it is L3 switch? Too bad it doesn't support VTP, but no big deal either. Thanks again!
... View more
09-08-2013
08:48 PM
Hi, I'd like to know how to configure VLANs in SG-500 with it's L3 functionality (switch router). The switch is up and running currently in L2 mode and has a few hosts connected to it. Some questions I have: If I switch it to L3 ( set system mode router ) what will happen to it? Will it still function as a normal L2 switch like it is now, or do I need to change some other configuration? Will the current hosts be affected? Does the L3 switch need to run VTP for VLANs? What if the router isn't a Cisco router (it's a SonicWALL)? Thank you in advance!
... View more
Labels:
Created by
wimpog97
in Small Business Switches
in Small Business Switches
09-07-2013
06:10 AM
09-07-2013
06:10 AM
Thank you, Tom!
... View more
Created by
wimpog97
in Small Business Switches
in Small Business Switches
09-06-2013
05:29 PM
09-06-2013
05:29 PM
The standare Cisco IOS command is show mac-address-table. This command isn't available on this switch. FW v1.3.0.62 Thanks.
... View more
- Tags:
- sg500
Labels:
09-24-2014
Thank you for your reply.Unfortunately, this command is not available in
Global Configuration mode. ...
Created by
wimpog97
in Small Business Switches
09-22-2014
09-22-2014
Is there a way to do switchport port-security violation {protect |
restrict | shutdown} in SG-500-28...
09-09-2013
Thanks Tom, I'll give it a try.I think, all I need to do is dedicate a
few ports to another VLAN and...
09-09-2013
Hi Tom,What if I just want to put a few ports into its own VLAN so they
can act as a separate switch...
09-09-2013
Hi Tom,In L3 Vlans is tagging nedded at all? Or is it there just for
backwards-compatibility with L2...
09-09-2013
Thanks Tom.Could you please tell me what functionality
appears/disappears in general once L3 is enab...
09-08-2013
Hi,I'd like to know how to configure VLANs in SG-500 with it's L3
functionality (switch router).The ...
Public Statistics
| Date Registered | 09-06-2013 05:24 PM |
| Date Last Visited | 08-18-2017 04:27 AM |
| Total Messages Posted | 11 |
