About PACC

PACC · 09-19-2024

Hi all,CUCM 11.5.1.12900-21Rocky Linux 9.4, OpenSSH_8.7p1, OpenSSL 3.0.7 1I am attempting to set the Rocky server as a backup device for CUCM. I initially got the errors regarding key exchange algorithms and host key types not matching, so I enabled...

PACC · 07-24-2024

Hey all,I have 6 switches using vtp v3 in transparent mode. switch01 is the primary.If I run show vtp status on any of the switches, they show switch01 as the primary.If I attempt to add a vlan to switch01,I get the message: VTP VLAN configuration n...

PACC · 12-04-2023

Hey all,Have a BE6000 running esxi 6.7.0 for CUCM. The Link Discovery Protocol option only has CDP. The BE6000 is currently connected to a Cisco C9300 switch, but I want to connect it to an Extreme 3750. I enabled CDP on the ports on the Extreme 3...

PACC · 10-16-2023

Hi all,I'm trying to create a port channel from an EdgeSwitch 24 to a Cisco 9300, but after testing by connecting just one cable I don't get any connectivity between them. The arp table on the 9300 shows the IP address of the edgeswitch but an incomp...

PACC · 09-17-2023

Hi all,After successfully moving two C9300 stacked switches without powering them off or affecting the network... we had a power event which forced them off Anyway, they powered back up ok and everything is running except a strange issue with the 10g...

PACC · 09-26-2024

Thanks for the reply @dpwaruna, the utils network connectivity command just reports success, but seeing as it doesn't ask for credentials it probably just reports that it got a credential prompt. I also don't want to use Windows unless I have to!It ...

PACC · 09-25-2024

admin:utils network connectivity 192.168.200.53 22Connection to 192.168.200.53 22 port [tcp/ssh] succeeded!Service accessibleI did get some jsch logs from cucm:2024-09-26 09:16:08,274 INFO [NetMessageDispatch] - Connecting to 192.168.200.53 port 2220...

PACC · 09-23-2024

Thanks for your replies @Elliot Dierksen I increased the debug level and have attached the result. I have a VMWare vCentre server backing up using the same credentials that is working successfully.I tried that IPQoS parameter but it hasn't made a di...

PACC · 09-22-2024

Thanks @Elliot Dierksen I have attempted to replicate your config but my version of OpenSSH does not support blowfish-cbc. The sshd daemon will not start with that in the config.I am copying and pasting the credentials so I don't get them wrong.Here...

PACC · 07-24-2024

Ha! That did it. I can see that the operating mode has changed to Primary Server. I kind of assumed that since all the switches saw sw01 as the primary then it was the primary.After some searching I see that this primary status doesn't survive a r...

Member Since	‎12-11-2013 03:49 PM
Date Last Visited	‎10-16-2024 05:15 PM
Posts	49

User Statistics

User Activity

CUCM DRS backup device error

VTP v3 cannot add vlan on server

Link Discovery Protocol options for vSwitch in esxi 6.7.0 on BE6000

Port Channel between Ubiquiti EdgeSwitch and Cisco 9300

Catalyst 9300 stack strange issue with 10gig interfaces

Re: CUCM DRS backup device error

Re: CUCM DRS backup device error

Re: CUCM DRS backup device error

Re: CUCM DRS backup device error

Re: VTP v3 cannot add vlan on server