About sushilmenon

sushilmenon · 04-08-2010

Hi All,I have 8 2960 switches in the network with 2 3750 as the aggregation switches in the network. I have stacked both the 3750 24 port switches.Now i am planning to connect each 2960 access switch with 2 gig uplinks in a ether-channel bundle with...

sushilmenon · 04-02-2010

Hi All,I have a access network with 8 2960 switches and 2 3560 switches as their aggregation switches. I have dual links from each of the 2960 switches connecting to each of the 3560 switches. The 3560 switches are only aggregating the vlans at layer...

sushilmenon · 04-02-2010

Hi all,I am in the phase of designing a Cisco VSS solution with 3560 as the aggreagtion switches.I have 2 3560 aggregation switches and 2 6509 switches. I have multiple 2960 switches connected to 3560 switches.I want to connect 3560 switches to the v...

sushilmenon · 05-27-2009

when the aip ssm module is in inline mode. does the packet first is scanned by the aip ssm module or it is first checked by the firewall rules whether it is permitted and then sent to aip ssm module. can someone throw some light on this. regardssushi...

sushilmenon · 05-27-2009

Hi all i am trying to figure out the load-balancing between 2 idsm2 modules in the same chassis. this is the config i am trying to dorouter(config)# intrusion-detection module 6 data-port 1 port-channel 5 (idsm1)router(config)# intrusion-detection mo...

sushilmenon · 04-02-2010

Hi Allan,Thanks a lot for your prompt and accurate reply.I have one more query about load-balacing VLAN Traffic within a single vlan. I have posted a new thread for the same in this same board.Can you please help me out with the same as well.Thanks &...

sushilmenon · 04-02-2010

Thanks Reza and Allan,Just one more query so as you all mentioned that i need a single ether-channel on the 3560 switch with one port of the ether-channel connecting to the primary vss switch and other connecting to the secondary vss switch right.Now...

sushilmenon · 04-02-2010

Hi ,Thanks for all your response.I have 8 2960 access switches and 2 3560 switches. All the access switches are in the same floor and same vlan. there is only a single vlan in all the access switches.The 3560 switches are only terminating the fibre u...

sushilmenon · 03-25-2009

Hi mark, remember in clientless ssl vpn there is no ip given to the end users. if u know in clientless ssl vpn the client request is sent to the asa who relays the traffic to the internal resource like ur win servers using cifs.here on the servers th...

sushilmenon · 03-25-2009

Hi i am glad my post was of little help to you. see the spi based nat is not dependant on nat-t. it;s a cisco feature and not a standard. by default after 12.3T ios when u enable pat on ios router. and when it sees esp traffic it by default starts sp...

Member Since	‎12-01-2007 03:33 AM
Date Last Visited	‎08-18-2017 03:53 AM
Posts	55
Total Helpful Votes Received	6

User Statistics

User Activity

Is this a correct access network design

Load-Balancing traffic within a single vlan

Cisco VSS with ether-channel uplinks from Aggregation switches

silly doubt about aip-ssm module

Load-Balancing between 2 idsm in single chassis inline mode

Re: Cisco VSS with ether-channel uplinks from Aggregation switch

Re: Cisco VSS with ether-channel uplinks from Aggregation switch

Re: Load-Balancing traffic within a single vlan

Re: Clientless SSL VPN and remote branch browsing via CIFS

Re: ESP though pat