Hi,      ip route 192.168.1.16 255.255.255.0 10.1.1.2---> this statement is wrong...  The network is not in correct format... if you configure this command in router it will show you error - Inconsistent address and mask. it should be --- ip route 192.168.1.0 255.255.255.0 10.1.1.2 , means remote network 192.168.1.0/24 is accessible via 10.1.1.2. ip route 0.0.0.0  0.0.0.0.0 192.168.1.17 : this statement is wrong, it should not be 5 octet in mask. It should like this 0.0.0.0 0.0.0.0 192.168.1.17 this is a default route means that all packet should go to 192.168.1.17. Hope this information will help you Do rate for helpful posts... Uttam http://www.startnetworks.blogspot.com/ ... View more

Hi,    Agreed to above answer.. This is a informational message that cache is full, then somenetflow statistics will be lost. Error Message   C4K_HWNETFLOWMAN-4-FLOWSLOSTERR: Netflow stats lost due to full hw flow table.  [char] [dec] packets. Explanation   This message indicates that if the cache is full, then some flow statistics will be lost. This message informs users about the total collected flow statistics. If the counter that tracks the lost statistics has overflowed, an accurate count of total lost flows is not available. Recommended Action   This is an informational message only. No action is required. http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.1/12.1e/system/message/emsg.html#wp1404615 To overcome this issue you have to configure minimum flowmask, The flow mask determines the granularity of the statistics gathered, which controls the size of the NetFlow table. The less-specific flow masks result in fewer entries in the NetFlow table and the most-specific flow masks result in the most NetFlow entries. For example, if the flow mask is set to source-only, the NetFlow table contains only one entry per source IP address. The statistics for all flows from a given source are accumulated in the one entry. However, if the flow mask is configured as full, the NetFlow table contains one entry per full flow. Many entries may exist per source IP address, so the NetFlow table can become very large. Setting the Minimum IP MLS Flow Mask You can set the minimum specificity of the flow mask for the NetFlow table on the PFC. The actual flow mask may be more specific than the level configured in the mls flow ip command, if other configured features need a more specific flow mask (see the "Flow Mask Conflicts" section). To set the minimum IP MLS flow mask, perform this task: Command Purpose Router(config)# mls flow ip {source | destination | destination-source | interface-destination-source | full | interface-full} Sets the minimum IP MLS flow mask for the protocol. Router(config)# no mls flow ip Reverts to the default IP MLS flow mask (null). This example shows how to set the minimum IP MLS flow mask: Router(config)# mls flow ip destination http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SXF/native/configuration/guide/netflow.html#wp1106378 Hope this information will help you.... Uttam http://www.startnetworks.blogspot.com ' ... View more

Hi,      Answer to your question "difference between the bootstrap (RXboot) program (0x2101) and ROMMON (0x2120)." Plz visit link : http://www.cisco.com/en/US/products/hw/routers/ps133/products_tech_note09186a008022493f.shtml Same time visit : http://www.cisco.com/en/US/products/hw/routers/ps270/products_installation_guide_chapter09186a00802ecd10.html "Does ROMMON supported on newer series of rotuter like the 2800 and the 3800." --- Yes, For more details visit: http://www.cisco.com/en/US/docs/routers/access/1800/1841/software/configuration/guide/b_rommon.html This document is for 2800 and 3800 Rommon troubleshooting... Uttam http://www.startnetworks.blogspot.com/ ... View more