07-11-2013 12:06 PM - edited 02-21-2020 07:01 PM
ASA : 8.2.5
ASDM: 6.4.5
LAN: 10.1.0.0/22
VPN Pool: 172.16.10.0/24
Hi, we purcahsed a new ASA 5505 and try to setup IPSEC VPN via ASDM; i just simply run the Wizards, setup vpnpool, split tunnelling,etc.
I can connect to the ASA by using cisco VPN client and internet works fine on the local PC, but it cannot access to the LAN (can't ping. can't remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile i created worked fine.
Below is my configure, do I mis-configure anything?
ASA Version 8.2(5)
!
hostname asatest
domain-name XXX.com
enable password 8Fw1QFqthX2n4uD3 encrypted
passwd g9NiG6oUPjkYrHNt encrypted
names
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
ip address 10.1.1.253 255.255.252.0
!
interface Vlan2
nameif outside
security-level 0
ip address XXX.XXX.XXX.XXX 255.255.255.240
!
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
dns server-group DefaultDNS
domain-name vff.com
access-list vpntest_splitTunnelAcl standard permit 10.1.0.0 255.255.252.0
access-list inside_nat0_outbound extended permit ip 10.1.0.0 255.255.252.0 172.16.10.0 255.255.255.0
pager lines 24
logging enable
logging timestamp
logging trap warnings
logging asdm informational
logging device-id hostname
logging host inside 10.1.1.230
mtu inside 1500
mtu outside 1500
ip local pool vpnpool 172.16.10.1-172.16.10.254 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server AD protocol nt
aaa-server AD (inside) host 10.1.1.108
nt-auth-domain-controller 10.1.1.108
http server enable
http 10.1.0.0 255.255.252.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 10.1.0.0 255.255.252.0 inside
ssh timeout 20
console timeout 0
dhcpd auto_config outside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy vpntest internal
group-policy vpntest attributes
wins-server value 10.1.1.108
dns-server value 10.1.1.108
vpn-tunnel-protocol IPSec l2tp-ipsec
password-storage disable
ip-comp disable
re-xauth disable
pfs disable
ipsec-udp disable
ipsec-udp-port 10000
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpntest_splitTunnelAcl
default-domain value XXX.com
split-tunnel-all-dns disable
backup-servers keep-client-config
address-pools value vpnpool
username admin password WeiepwREwT66BhE9 encrypted privilege 15
username user5 password yIWniWfceAUz1sUb encrypted privilege 5
username user3 password umNHhJnO7McrLxNQ encrypted privilege 3
tunnel-group vpntest type remote-access
tunnel-group vpntest general-attributes
address-pool vpnpool
authentication-server-group AD
authentication-server-group (inside) AD
default-group-policy vpntest
strip-realm
tunnel-group vpntest ipsec-attributes
pre-shared-key BEKey123456
peer-id-validate nocheck
!
!
privilege cmd level 3 mode exec command perfmon
privilege cmd level 3 mode exec command ping
privilege cmd level 3 mode exec command who
privilege cmd level 3 mode exec command logging
privilege cmd level 3 mode exec command failover
privilege cmd level 3 mode exec command packet-tracer
privilege show level 5 mode exec command import
privilege show level 5 mode exec command running-config
privilege show level 3 mode exec command reload
privilege show level 3 mode exec command mode
privilege show level 3 mode exec command firewall
privilege show level 3 mode exec command asp
privilege show level 3 mode exec command cpu
privilege show level 3 mode exec command interface
privilege show level 3 mode exec command clock
privilege show level 3 mode exec command dns-hosts
privilege show level 3 mode exec command access-list
privilege show level 3 mode exec command logging
privilege show level 3 mode exec command vlan
privilege show level 3 mode exec command ip
privilege show level 3 mode exec command ipv6
privilege show level 3 mode exec command failover
privilege show level 3 mode exec command asdm
privilege show level 3 mode exec command arp
privilege show level 3 mode exec command route
privilege show level 3 mode exec command ospf
privilege show level 3 mode exec command aaa-server
privilege show level 3 mode exec command aaa
privilege show level 3 mode exec command eigrp
privilege show level 3 mode exec command crypto
privilege show level 3 mode exec command vpn-sessiondb
privilege show level 3 mode exec command ssh
privilege show level 3 mode exec command dhcpd
privilege show level 3 mode exec command vpnclient
privilege show level 3 mode exec command vpn
privilege show level 3 mode exec command blocks
privilege show level 3 mode exec command wccp
privilege show level 3 mode exec command dynamic-filter
privilege show level 3 mode exec command webvpn
privilege show level 3 mode exec command module
privilege show level 3 mode exec command uauth
privilege show level 3 mode exec command compression
privilege show level 3 mode configure command interface
privilege show level 3 mode configure command clock
privilege show level 3 mode configure command access-list
privilege show level 3 mode configure command logging
privilege show level 3 mode configure command ip
privilege show level 3 mode configure command failover
privilege show level 5 mode configure command asdm
privilege show level 3 mode configure command arp
privilege show level 3 mode configure command route
privilege show level 3 mode configure command aaa-server
privilege show level 3 mode configure command aaa
privilege show level 3 mode configure command crypto
privilege show level 3 mode configure command ssh
privilege show level 3 mode configure command dhcpd
privilege show level 5 mode configure command privilege
privilege clear level 3 mode exec command dns-hosts
privilege clear level 3 mode exec command logging
privilege clear level 3 mode exec command arp
privilege clear level 3 mode exec command aaa-server
privilege clear level 3 mode exec command crypto
privilege clear level 3 mode exec command dynamic-filter
privilege cmd level 3 mode configure command failover
privilege clear level 3 mode configure command logging
privilege clear level 3 mode configure command arp
privilege clear level 3 mode configure command crypto
privilege clear level 3 mode configure command aaa-server
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4
: end
Solved! Go to Solution.
07-11-2013 03:48 PM
From the captures we can see packets going from the Pool to the internal LAN but we cannot see any reply packets coming back.
The routing should be such that for 172.16.10.0/24 the packets should reach the inside interface of this ASA.
So either on the client machines or the switch in your internal LAN you need to add route for 172.16.10.0/24 pointing towards the inside interface of this ASA.
07-11-2013 12:15 PM
Hi Sai,
Can you take captures on your inside interface (behind which your Local LAN is) and check if you can see bi-directional traffic or not?
It seems like on your internal LAN there might be a routing issue,ie, a device in between might not be routing traffic back to the ASA for the pool IP subnet.
To take captures create an ACL,
access-list test123 permit ip host x.x.x.x host y.y.y.y
access-list test123 permit ip host y.y.y.y host x.x.x.x
cap test123 interface inside access-list test123
show cap test123
x.x.x.x = Pool ip address which your client machine gets
y.y.y.y = IP address you are trying to ping in your internal LAN.
Check if you see packets going out to the internal LAN and if you see reply packets or not. If you don't check your internal routing and if there is another firewall in between check if traffic to pool is allowed on that.
HTH
07-11-2013 12:18 PM
Also, just to add if management access in enabled on the inside interface, can you try and ping the inside interface of ASA and see if you get replies for that?
07-11-2013 03:11 PM
Thank you for your response. I think i found something: this ASA is a acted as a sceondry gateway of the LAN, the rest of the computers in the LAN are using the other ASA as thier default gateway. If i change a pc's gateway, then i can get ping response back.
I tested on the production ASA, i can ping every computer on the LAN, no matter what's their gateway is, but this new ASA act can't Also, While Remoted in, I cannot ping this ASA's inside IP.
07-11-2013 03:32 PM
Below is the capture:
asatest# show cap test
8 packets captured
1: 15:09:24.337842 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request
2: 15:09:26.997323 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
3: 15:09:28.457923 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
4: 15:09:28.796772 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request
5: 15:09:30.046292 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
6: 15:09:31.457633 802.1Q vlan#1 P0 172.16.10.1.5544 > 10.1.1.108.3389: S 321718812:321718812(0) win 8192
7: 15:09:33.795231 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request
8: 15:09:34.434853 802.1Q vlan#1 P0 172.16.10.1.5544 > 10.1.1.108.3389: S 321718812:321718812(0) win 8192
8 packets shown
07-11-2013 03:48 PM
From the captures we can see packets going from the Pool to the internal LAN but we cannot see any reply packets coming back.
The routing should be such that for 172.16.10.0/24 the packets should reach the inside interface of this ASA.
So either on the client machines or the switch in your internal LAN you need to add route for 172.16.10.0/24 pointing towards the inside interface of this ASA.
07-11-2013 06:42 PM
I change a Machine's gateway to this ASA and capture again, now we can see some reply.
All ohter PCs and switches gateway are point to another ASA, maybe that's the reason why i didn't work?
what's the recommanded way to make our LAN to have two 2 gateways(for load balance or backup router, etc)?
add two gateways to all PCs and swtichwes?
1: 18:15:48.307875 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
2: 18:15:49.777685 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
3: 18:15:51.377147 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
4: 18:15:57.445777 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
5: 18:15:58.856324 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
6: 18:16:00.395090 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
7: 18:16:06.483464 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
8: 18:16:08.082805 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
9: 18:16:09.542406 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 68
10: 18:16:20.640424 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
11: 18:16:20.642193 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
12: 18:16:21.169607 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
13: 18:16:21.171210 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
14: 18:16:22.179556 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
15: 18:16:22.181142 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
16: 18:16:23.237673 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.230: icmp: echo request
17: 18:16:23.239291 802.1Q vlan#1 P0 10.1.1.230 > 172.16.10.1: icmp: echo reply
18: 18:16:27.676402 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
19: 18:16:29.246935 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
20: 18:16:30.676921 802.1Q vlan#1 P0 172.16.10.1.137 > 10.1.1.108.137: udp 50
21: 18:16:49.539660 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request
22: 18:16:54.952602 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request
23: 18:17:04.511463 802.1Q vlan#1 P0 172.16.10.1 > 10.1.1.233: icmp: echo request
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide