04-11-2012 09:41 AM
Hi,
I'm trying to configure my Cisco Pix 501 behind adsl router (Linksys with 1 public ip only!!). I configure it on DMZ and I can to connect with ssh, pdm etc from my office.
I cannot to connect with vpn client.
This is my configuration:
PIX Version 6.3(5)
interface ethernet0 100full
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password V6IL8GTNlbf/rkrD encrypted
passwd V6IL8GTNlbf/rkrD encrypted
hostname pix-chri
domain-name acantho.com
clock timezone METDST 1
clock summer-time METDST recurring last Sun Mar 2:00 last Sun Oct 2:00
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list inside_access_in permit ip 10.0.0.0 255.255.255.0 any
access-list inside_access_in permit icmp any any
access-list inside_access_out permit icmp any any
access-list HOME_VPN_splitTunnelAcl permit ip any any
access-list inside_outbound_nat0_acl permit ip any 10.0.1.4 255.255.255.252
access-list outside_cryptomap_dyn_20 permit ip any 10.0.1.4 255.255.255.252
pager lines 24
logging on
logging console notifications
logging buffered notifications
mtu outside 1500
mtu inside 1500
ip address outside 192.168.1.253 255.255.255.0
ip address inside 10.0.0.254 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool casapool 10.0.1.5-10.0.1.7
pdm location xxx.xxx.185.125 255.255.255.255 outside
pdm location 192.168.1.0 255.255.255.0 outside
pdm location 10.0.0.0 255.255.255.0 inside
pdm location xxx.xxx.192.133 255.255.255.255 outside
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_outbound_nat0_acl
nat (inside) 1 10.0.0.0 255.255.255.0 0 0
access-group inside_access_out in interface outside
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 192.168.1.1 1
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout sip-disconnect 0:02:00 sip-invite 0:03:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
aaa authentication ssh console LOCAL
ntp server xx.xxx.160.1 source outside
http server enable
http 192.168.1.0 255.255.255.0 outside
http xxx.xxx.1xx.115 255.255.255.255 outside
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set myset-des esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto dynamic-map outside_dyn_map 20 match address outside_cryptomap_dyn_20
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map client authentication LOCAL
crypto map outside_map interface outside
isakmp enable outside
isakmp identity address
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption 3des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
vpngroup HOME_VPN address-pool casapool
vpngroup HOME_VPN dns-server 192.168.1.1 xxx.xxx.160.1
vpngroup HOME_VPN split-tunnel HOME_VPN_splitTunnelAcl
vpngroup HOME_VPN idle-time 1800
vpngroup HOME_VPN password ********
telnet timeout 5
ssh xx.xxx.xxx.115 255.255.255.255 outside
ssh xxx.xxx.1xx.33 255.255.255.255 outside
ssh 192.168.1.0 255.255.255.0 outside
ssh 10.0.0.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 10.0.0.1-10.0.0.25 inside
dhcpd dns 192.168.1.1
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd enable inside
username xxx password xxxxxxxxxxxxxx encrypted privilege 15
terminal width 80
some idea?
Thanks
04-12-2012 05:45 AM
Dear Christian,
Thank you for posting.
Please add the following commands in configuration mode:
isakmp key cisco1234 address 0.0.0.0 netmask 0.0.0.0 ---> Group password
isakmp nat-traversal 20
Make sure the client is properly configured:
Then, turn on debugging and try to connect:
debug crypto isakmp
debug crypto ipsec
*Please make sure you have enough lines of scrollback.
Further reference: http://www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/basclnt.html
Please keep me posted.
Thanks.
04-12-2012 03:06 PM
Hi and thank you.
I added your line but dont'work.
I think it's dmz confiugration, maybe don't work ESP protocol ....
I can not see anything from the debug console. From internal ip it's work (I only have some error with policy).
04-12-2012 08:15 PM
Hi,
One thing I did not notice, please issue the following for now:
no crypto dynamic-map outside_dyn_map 20 match address outside_cryptomap_dyn_20
Also, what does the client report? Remote gateway not longer responding?
The ESP packets are not the issue, at this point you need to make sure that ISAKMP (UDP port 500) is allowed and your ISP permits this traffic.
A packet-capture will be required to confirm whether the PIX receives the traffic or not.
http://www.cisco.com/en/US/docs/security/pix/pix63/command/reference/c.html#wp1053548
In your case:
access-list isakmp permit udp host 192.168.1.253 any eq 500
access-list isakmp permit udp any host 192.168.1.253 eq 500
capture isakmp access-list isakmp interface outside
Then try to connect and run the following command:
show capture isakmp
Please keep me posted.
Thanks.
04-13-2012 03:22 PM
Hi Javier,
now the setup works.
I had problems with NAT rules on my linksys router.
Now I can connect to my PIX through DMZ of my router --> Internet --> Router Linksys (192.168.1.1) -->DMZ --> OUTSIDE IP 192.168.1.253 --> Pix 501 --> INSIDE IP 10.0.0.254
Unfortunately I still can not reach any hosts on the network:
on my external Vpn Client I have:
IPv4. . . . . . . . . . . . : 10.0.1.5
Subnet mask . . . . . . . . . . . . . : 255.255.255.252
Gateway . . . . . . . . . : 10.0.1.6
Route print
10.0.1.4 255.255.255.252 On-link 10.0.1.5 276
10.0.1.5 255.255.255.255 On-link 10.0.1.5 276
10.0.1.7 255.255.255.255 On-link 10.0.1.5 276
I can not get no address ... 192.168.1.x or 10.0.0.x
Thank you very much
This is my last config:
interface ethernet0 100full
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password V6IL8GTNlbf/rkrD encrypted
passwd V6IL8GTNlbf/rkrD encrypted
hostname pix-chri
domain-name acantho.com
clock timezone METDST 1
clock summer-time METDST recurring last Sun Mar 2:00 last Sun Oct 2:00
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list inside_access_in permit ip 10.0.0.0 255.255.255.0 any
access-list inside_access_in permit icmp any any
access-list inside_access_out permit icmp any any
access-list HOME_VPN_splitTunnelAcl permit ip any any
access-list inside_outbound_nat0_acl permit ip any 10.0.1.4 255.255.255.252
access-list outside_cryptomap_dyn_20 permit ip any 10.0.1.4 255.255.255.252
pager lines 24
logging on
logging console notifications
logging buffered notifications
mtu outside 1500
mtu inside 1500
ip address outside 192.168.1.253 255.255.255.0
ip address inside 10.0.0.254 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool casapool 10.0.1.5-10.0.1.7 mask 255.255.255.252
###PDM config ok###
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_outbound_nat0_acl
nat (inside) 1 10.0.0.0 255.255.255.0 0 0
access-group inside_access_out in interface outside
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 192.168.1.1 1
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout sip-disconnect 0:02:00 sip-invite 0:03:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
aaa authentication ssh console LOCAL
ntp server 213.174.160.1 source outside
###http config ok#####
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set myset-des esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto dynamic-map outside_dyn_map 20 match address outside_cryptomap_dyn_20
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map client authentication LOCAL
crypto map outside_map interface outside
isakmp enable outside
isakmp identity address
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption 3des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
vpngroup HOME_VPN address-pool casapool
vpngroup HOME_VPN dns-server 192.168.1.1 213.174.160.1
vpngroup HOME_VPN split-tunnel HOME_VPN_splitTunnelAcl
vpngroup HOME_VPN idle-time 1800
vpngroup HOME_VPN password ********
telnet timeout 5
ssh timeout 5
###ssh config ok@@@@
console timeout 0
dhcpd address 10.0.0.1-10.0.0.25 inside
dhcpd dns 192.168.1.1
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd enable inside
username user password xxxxxxxxxxxxxxxx encrypted privilege 15
terminal width 80
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide