04-23-2014 04:12 PM - edited 02-21-2020 07:36 PM
I have a remote access VPN configured on a device here. I'm able to connect a device and it assigns me an IP address out of the pool, and injects the routes to its local network, but I'm not able to pass any traffic through the VPN and none of the IPSec SA counters increment for the dial-in connection. I've compared the config here to the samples from documentation and I don't know what I'm missing. Config is below.
3118-FWL001(config)# sho run
: Saved
:
ASA Version 7.2(3)
!
hostname 3118-FWL001
domain-name rr-rentals.com
enable password hEgvNHfNHV8zypPu encrypted
names
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.10.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address 199.X.X.162 255.255.255.248
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passwd 2KFQnbNIdI.2KYOU encrypted
banner exec
banner exec
banner exec
banner exec Any attempted or unauthorized access, use, or modification is prohibited.
banner exec Unauthorized users may face criminal and/or civil penalties.
banner exec The use of this system may be monitored and recorded.
banner exec If the monitoring reveals possible evidence of criminal activity, Adhost can
banner exec provide the records to law enforcement.
banner exec Be safe! Do not share your access information with anyone!
banner exec
banner exec
banner exec
banner asdm
banner asdm
banner asdm
banner asdm Any attempted or unauthorized access, use, or modification is prohibited.
banner asdm Unauthorized users may face criminal and/or civil penalties.
banner asdm The use of this system may be monitored and recorded.
banner asdm If the monitoring reveals possible evidence of criminal activity, Adhost can
banner asdm provide the records to law enforcement.
banner asdm Be safe! Do not share your access information with anyone!
banner asdm
banner asdm
banner asdm
ftp mode passive
dns server-group DefaultDNS
domain-name rr-rentals.com
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
access-list outside_acl extended permit ip any host 199.X.X.163
access-list outside_acl extended permit icmp any any echo
access-list outside_acl extended permit icmp any any echo-reply
access-list outside_acl extended permit tcp 216.X.X.64 255.255.255.192 any
access-list outside_acl extended permit tcp host 76.X.X.166 any eq 3389
access-list outside_acl extended permit tcp 67.X.X.192 255.255.255.224 any eq 3389
access-list outside_acl extended permit tcp any any eq ftp
access-list outside_acl extended permit tcp any any eq ftp-data
access-list outside_acl extended permit tcp host 72.X.X.71 any eq 3389
access-list outside_acl extended permit tcp host 26.X.X.155 any eq 3389
access-list outside_acl extended permit tcp host 24.X.X.155 any eq 3389
access-list outside_acl extended permit icmp any any unreachable
access-list outside_acl extended permit icmp any any time-exceeded
access-list outside_acl extended permit tcp host 71.X.X.170 any eq 3389
access-list outside_acl extended permit tcp host 24.X.X.200 any eq 3389
access-list inside_nat0_outbound extended permit ip 192.168.10.0 255.255.255.0 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.10.0 255.255.255.0 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.10.0 255.255.255.0 192.168.4.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.10.0 255.255.255.0 192.168.3.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.10.0 255.255.255.0 192.168.20.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 192.168.20.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.20.0 255.255.255.0 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.20.0 255.255.255.0 192.168.10.0 255.255.255.0
access-list outside_1_cryptomap extended permit ip 192.168.10.0 255.255.255.0 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap extended permit ip 192.168.20.0 255.255.255.0 192.168.1.0 255.255.255.0
access-list outside_2_cryptomap extended permit ip 192.168.10.0 255.255.255.0 192.168.2.0 255.255.255.0
access-list outside_4_cryptomap extended permit ip 192.168.10.0 255.255.255.0 192.168.4.0 255.255.255.0
access-list outside_3_cryptomap extended permit ip 192.168.10.0 255.255.255.0 192.168.3.0 255.255.255.0
access-list rr-vpn_splitTunnelAcl standard permit 192.168.10.0 255.255.255.0
access-list rr-vpn_splitTunnelAcl standard permit 192.168.1.0 255.255.255.0
pager lines 24
logging enable
logging buffer-size 1048576
logging buffered debugging
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpnpool 192.168.20.1-192.168.20.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-523.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) 199.X.X.163 192.168.10.2 netmask 255.255.255.255
access-group outside_acl in interface outside
route outside 0.0.0.0 0.0.0.0 199.X.X.161 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
aaa authentication ssh console LOCAL
aaa authentication http console LOCAL
aaa authentication enable console LOCAL
aaa authentication serial console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
http 216.X.X.64 255.255.255.192 outside
http 0.0.0.0 0.0.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sysopt connection tcpmss 1200
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map outside_dyn_map 20 set pfs
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 50.X.X.58
crypto map outside_map 1 set transform-set ESP-AES-128-SHA
crypto map outside_map 2 match address outside_2_cryptomap
crypto map outside_map 2 set pfs
crypto map outside_map 2 set peer 75.X.X.253
crypto map outside_map 2 set transform-set ESP-AES-128-SHA
crypto map outside_map 3 match address outside_3_cryptomap
crypto map outside_map 3 set pfs
crypto map outside_map 3 set peer 173.X.X.69
crypto map outside_map 3 set transform-set ESP-AES-128-SHA
crypto map outside_map 4 match address outside_4_cryptomap
crypto map outside_map 4 set pfs
crypto map outside_map 4 set peer 70.X.X.194
crypto map outside_map 4 set transform-set ESP-AES-128-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes
hash sha
group 5
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 192.168.10.2 255.255.255.255 inside
ssh 192.168.0.0 255.255.0.0 inside
ssh 216.X.X.64 255.255.255.192 outside
ssh 50.X.X.58 255.255.255.255 outside
ssh timeout 60
ssh version 2
console timeout 0
management-access inside
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect icmp
inspect icmp error
!
service-policy global_policy global
tftp-server outside 216.X.X.116 3118-FWL001.config
group-policy rr-vpn internal
group-policy rr-vpn attributes
dns-server value 216.X.X.12 66.X.X.11
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value rr-vpn_splitTunnelAcl
username rrlee password B6rKS8LmKC50oIXK encrypted privilege 0
username rrlee attributes
vpn-group-policy rr-vpn
username cschirado password QYICGrOFAZ9iPWpp encrypted privilege 0
username cschirado attributes
vpn-group-policy rr-vpn
username daniel password SZsXZCSuVXcFn9NB encrypted privilege 15
username adhostadm password 7P2Y2Ow1o0.VSjvh encrypted privilege 15
username troy password amZKsxVU.8N9kKPb encrypted privilege 0
username troy attributes
vpn-group-policy rr-vpn
username troyr password Hek9zbMrM6wEDSfi encrypted privilege 15
username druiz password 33oau7XOcvhJ3DMv encrypted privilege 0
username druiz attributes
vpn-group-policy rr-vpn
username theresa password qWsPnR.vfjXzlunC encrypted privilege 0
username theresa attributes
vpn-group-policy rr-vpn
username kevin password R5DPfUVhzGCEg6pu encrypted privilege 0
username kevin attributes
vpn-group-policy rr-vpn
username andrea password MyhIPdH6UJQDon77 encrypted privilege 0
username andrea attributes
vpn-group-policy rr-vpn
tunnel-group 50.X.X.58 type ipsec-l2l
tunnel-group 50.X.X.58 ipsec-attributes
pre-shared-key *
tunnel-group 75.X.X.253 type ipsec-l2l
tunnel-group 75.X.X.253 ipsec-attributes
pre-shared-key *
tunnel-group 72.X.X.71 type ipsec-l2l
tunnel-group 72.X.X.71 ipsec-attributes
pre-shared-key *
tunnel-group 173.X.X.69 type ipsec-l2l
tunnel-group 173.X.X.69 ipsec-attributes
pre-shared-key *
tunnel-group rr-vpn type ipsec-ra
tunnel-group rr-vpn general-attributes
address-pool vpnpool
default-group-policy rr-vpn
tunnel-group rr-vpn ipsec-attributes
pre-shared-key *
tunnel-group 70.X.X.194 type ipsec-l2l
tunnel-group 70.X.X.194 ipsec-attributes
pre-shared-key *
prompt hostname context
04-23-2014 04:20 PM
Hi,
Could you please share output of following commands when connect to the ASA and pinging (inside interface of the ASA) constantly.
Show crypto isa sa
show crypto ipsec sa
show run route
If you receive response from the inside interface then try to ping anything further.
Vishnu
04-23-2014 04:26 PM
Here are the results of the commands you requested. I'm not able to ping either direction.
Thanks,
James
3118-FWL001# sho cry isa sa
Active SA: 5
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 5
1 IKE Peer: 50.34.254.58
Type : L2L Role : responder
Rekey : no State : MM_ACTIVE
2 IKE Peer: 173.10.71.69
Type : L2L Role : responder
Rekey : no State : MM_ACTIVE
3 IKE Peer: 75.151.109.253
Type : L2L Role : initiator
Rekey : no State : MM_ACTIVE
4 IKE Peer: 70.99.88.194
Type : L2L Role : initiator
Rekey : no State : MM_ACTIVE
5 IKE Peer: 216.211.143.85
Type : user Role : responder
Rekey : no State : AM_ACTIVE
3118-FWL001# sho cry ips sa
interface: outside
Crypto map tag: outside_dyn_map, seq num: 20, local addr: 199.21.66.162
local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
remote ident (addr/mask/prot/port): (192.168.20.2/255.255.255.255/0/0)
current_peer: 216.211.143.85, username: kevin
dynamic allocated peer ip: 192.168.20.2
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
#pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 199.21.66.162, remote crypto endpt.: 216.211.143.85
path mtu 1500, ipsec overhead 58, media mtu 1500
current outbound spi: CBF94621
inbound esp sas:
spi: 0x8D8279CA (2374138314)
transform: esp-3des esp-sha-hmac none
in use settings ={RA, Tunnel, }
slot: 0, conn_id: 200, crypto-map: outside_dyn_map
sa timing: remaining key lifetime (sec): 28715
IV size: 8 bytes
replay detection support: Y
outbound esp sas:
spi: 0xCBF94621 (3422111265)
transform: esp-3des esp-sha-hmac none
in use settings ={RA, Tunnel, }
slot: 0, conn_id: 200, crypto-map: outside_dyn_map
sa timing: remaining key lifetime (sec): 28715
IV size: 8 bytes
replay detection support: Y
Crypto map tag: outside_map, seq num: 1, local addr: 199.21.66.162
access-list outside_1_cryptomap permit ip 192.168.10.0 255.255.255.0 192.168.1.0 255.255.255.0
local ident (addr/mask/prot/port): (192.168.10.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
current_peer: 50.34.254.58
#pkts encaps: 15356573, #pkts encrypt: 15356573, #pkts digest: 15356573
#pkts decaps: 9021115, #pkts decrypt: 9021114, #pkts verify: 9021114
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 15356573, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 199.21.66.162, remote crypto endpt.: 50.34.254.58
path mtu 1500, ipsec overhead 74, media mtu 1500
current outbound spi: FE16571B
inbound esp sas:
spi: 0x78BD7E4F (2025684559)
transform: esp-aes esp-sha-hmac none
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 86, crypto-map: outside_map
sa timing: remaining key lifetime (kB/sec): (4263158/5788)
IV size: 16 bytes
replay detection support: Y
outbound esp sas:
spi: 0xFE16571B (4262876955)
transform: esp-aes esp-sha-hmac none
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 86, crypto-map: outside_map
sa timing: remaining key lifetime (kB/sec): (4064653/5788)
IV size: 16 bytes
replay detection support: Y
Crypto map tag: outside_map, seq num: 4, local addr: 199.21.66.162
access-list outside_4_cryptomap permit ip 192.168.10.0 255.255.255.0 192.168.4.0 255.255.255.0
local ident (addr/mask/prot/port): (192.168.10.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.4.0/255.255.255.0/0/0)
current_peer: 70.99.88.194
#pkts encaps: 491814, #pkts encrypt: 491814, #pkts digest: 491814
#pkts decaps: 416810, #pkts decrypt: 416810, #pkts verify: 416810
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 491814, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 199.21.66.162, remote crypto endpt.: 70.99.88.194
path mtu 1500, ipsec overhead 74, media mtu 1500
current outbound spi: 533F55E1
inbound esp sas:
spi: 0xE2F461AD (3807666605)
transform: esp-aes esp-sha-hmac none
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 194, crypto-map: outside_map
sa timing: remaining key lifetime (kB/sec): (4273818/27167)
IV size: 16 bytes
replay detection support: Y
outbound esp sas:
spi: 0x533F55E1 (1396659681)
transform: esp-aes esp-sha-hmac none
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 194, crypto-map: outside_map
sa timing: remaining key lifetime (kB/sec): (4266133/27167)
IV size: 16 bytes
replay detection support: Y
Crypto map tag: outside_map, seq num: 2, local addr: 199.21.66.162
access-list outside_2_cryptomap permit ip 192.168.10.0 255.255.255.0 192.168.2.0 255.255.255.0
local ident (addr/mask/prot/port): (192.168.10.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.2.0/255.255.255.0/0/0)
current_peer: 75.151.109.253
#pkts encaps: 207718, #pkts encrypt: 207718, #pkts digest: 207718
#pkts decaps: 142739, #pkts decrypt: 142739, #pkts verify: 142739
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 207722, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 199.21.66.162, remote crypto endpt.: 75.151.109.253
path mtu 1500, ipsec overhead 74, media mtu 1500
current outbound spi: 8D74AC18
inbound esp sas:
spi: 0x0CF7F70B (217577227)
transform: esp-aes esp-sha-hmac none
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 195, crypto-map: outside_map
sa timing: remaining key lifetime (kB/sec): (4274490/23242)
IV size: 16 bytes
replay detection support: Y
outbound esp sas:
spi: 0x8D74AC18 (2373233688)
transform: esp-aes esp-sha-hmac none
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 195, crypto-map: outside_map
sa timing: remaining key lifetime (kB/sec): (4270718/23242)
IV size: 16 bytes
replay detection support: Y
Crypto map tag: outside_map, seq num: 3, local addr: 199.21.66.162
access-list outside_3_cryptomap permit ip 192.168.10.0 255.255.255.0 192.168.3.0 255.255.255.0
local ident (addr/mask/prot/port): (192.168.10.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.3.0/255.255.255.0/0/0)
current_peer: 173.10.71.69
#pkts encaps: 3427935, #pkts encrypt: 3427935, #pkts digest: 3427935
#pkts decaps: 2006044, #pkts decrypt: 2006044, #pkts verify: 2006044
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 3427935, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 199.21.66.162, remote crypto endpt.: 173.10.71.69
path mtu 1500, ipsec overhead 74, media mtu 1500
current outbound spi: 2E8A6147
inbound esp sas:
spi: 0x467968AB (1182361771)
transform: esp-aes esp-sha-hmac none
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 154, crypto-map: outside_map
sa timing: remaining key lifetime (kB/sec): (4270213/18597)
IV size: 16 bytes
replay detection support: Y
outbound esp sas:
spi: 0x2E8A6147 (780820807)
transform: esp-aes esp-sha-hmac none
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 154, crypto-map: outside_map
sa timing: remaining key lifetime (kB/sec): (4162093/18597)
IV size: 16 bytes
replay detection support: Y
3118-FWL001# sho run route
route outside 0.0.0.0 0.0.0.0 199.21.66.161 1
04-23-2014 05:35 PM
Hi,
I see that only one user is connected and it with the ip address: 216.211.143.85
When I see Ipsec sa's for the same peer, I see that the SA's are up but encaps/decaps is still 0.
The ip address assigned to the client can be seen in the output of show crypto ipsec sa: dynamic allocated peer ip: 192.168.20.2
Try to ping this ip address making inside interface as the source and then run "show crypto ipsec sa" and see if there is any increase in encaps and decaps.
Also, I would suggest you to connect from a different machine and check if this works or not. If it still does not work then please get me output of the command:
packet-tracer in inside icmp 192.168.10.10 8 0 192.168.20.x detail. Here 192.168.20.x is the ip address assigned to the external VPN client.
Vishnu
04-23-2014 05:43 PM
I have a customer who's seeing the same behavior. Connects, unable to reach anything on the 192.168.10.x network.
The requested information is below.
3118-FWL001# ping inside 192.168.20.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.20.2, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
3118-FWL001# sho cry ips sa
interface: outside
Crypto map tag: outside_dyn_map, seq num: 20, local addr: 199.21.66.162
local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
remote ident (addr/mask/prot/port): (192.168.20.2/255.255.255.255/0/0)
current_peer: 216.211.143.85, username: kevin
dynamic allocated peer ip: 192.168.20.2
#pkts encaps: 5, #pkts encrypt: 5, #pkts digest: 5
#pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 5, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 199.21.66.162, remote crypto endpt.: 216.211.143.85
path mtu 1500, ipsec overhead 58, media mtu 1500
current outbound spi: 49B2A368
inbound esp sas:
spi: 0xE5F78E93 (3858206355)
transform: esp-3des esp-sha-hmac none
in use settings ={RA, Tunnel, }
3118-FWL001# packet-tracer in inside icmp 192.168.10.10 8 0 192.168.20.2 detail
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
Forward Flow based lookup yields rule:
in id=0x354d568, priority=1, domain=permit, deny=false
hits=113261577, user_data=0x0, cs_id=0x0, l3_type=0x8
src mac=0000.0000.0000, mask=0000.0000.0000
dst mac=0000.0000.0000, mask=0000.0000.0000
Phase: 2
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 3
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 192.168.20.2 255.255.255.255 outside
Phase: 4
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0x3550890, priority=0, domain=permit-ip-option, deny=true
hits=4663836, user_data=0x0, cs_id=0x0, reverse, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0
Phase: 5
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class inspection_default
inspect icmp
service-policy global_policy global
Additional Information:
Forward Flow based lookup yields rule:
in id=0x358aef8, priority=70, domain=inspect-icmp, deny=false
hits=1, user_data=0x358ad58, cs_id=0x0, use_real_addr, flags=0x0, protocol=1
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0
Phase: 6
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0x3da47a0, priority=70, domain=inspect-icmp-error, deny=false
hits=1, user_data=0x3da4600, cs_id=0x0, use_real_addr, flags=0x0, protocol=1
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0
Phase: 7
Type: NAT-EXEMPT
Subtype:
Result: ALLOW
Config:
nat (inside) 0 access-list inside_nat0_outbound
match ip inside 192.168.10.0 255.255.255.0 outside 192.168.20.0 255.255.255.0
NAT exempt
translate_hits = 8, untranslate_hits = 119
Additional Information:
Forward Flow based lookup yields rule:
in id=0x36bbab0, priority=6, domain=nat-exempt, deny=false
hits=7, user_data=0x36bba40, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
src ip=192.168.10.0, mask=255.255.255.0, port=0
dst ip=192.168.20.0, mask=255.255.255.0, port=0
Phase: 8
Type: NAT
Subtype:
Result: ALLOW
Config:
nat (inside) 1 0.0.0.0 0.0.0.0
match ip inside any outside any
dynamic translation to pool 1 (199.21.66.162 [Interface PAT])
translate_hits = 88, untranslate_hits = 0
Additional Information:
Forward Flow based lookup yields rule:
in id=0x36bf688, priority=1, domain=nat, deny=false
hits=88, user_data=0x36bf618, cs_id=0x0, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0
Phase: 9
Type: NAT
Subtype: host-limits
Result: ALLOW
Config:
nat (inside) 1 0.0.0.0 0.0.0.0
match ip inside any inside any
dynamic translation to pool 1 (No matching global)
translate_hits = 0, untranslate_hits = 0
Additional Information:
Forward Flow based lookup yields rule:
in id=0x36bf378, priority=1, domain=host, deny=false
hits=133, user_data=0x36bef30, cs_id=0x0, reverse, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0
Phase: 10
Type: HOST-LIMIT
Subtype:
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0x3ce31f8, priority=0, domain=host-limit, deny=false
hits=4352254, user_data=0x0, cs_id=0x0, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0
Phase: 11
Type: VPN
Subtype: encrypt
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
out id=0x3e8a9d0, priority=70, domain=encrypt, deny=false
hits=1, user_data=0x3b77084, cs_id=0x0, reverse, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=192.168.20.2, mask=255.255.255.255, port=0
Phase: 12
Type: VPN
Subtype: ipsec-tunnel-flow
Result: ALLOW
Config:
Additional Information:
Reverse Flow based lookup yields rule:
in id=0x3e993b0, priority=69, domain=ipsec-tunnel-flow, deny=false
hits=1, user_data=0x3b9e11c, cs_id=0x0, reverse, flags=0x0, protocol=0
src ip=192.168.20.2, mask=255.255.255.255, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0
Phase: 13
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Reverse Flow based lookup yields rule:
in id=0x35869c8, priority=0, domain=permit-ip-option, deny=true
hits=5523984, user_data=0x0, cs_id=0x0, reverse, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0
Phase: 14
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 5990975, packet dispatched to next module
Module information for forward flow ...
snp_fp_inspect_ip_options
snp_fp_inspect_icmp
snp_fp_adjacency
snp_fp_encrypt
snp_fp_fragment
snp_fp_tracer_drop
snp_ifc_stat
Module information for reverse flow ...
snp_fp_inspect_ip_options
snp_fp_ipsec_tunnel_flow
snp_fp_inspect_icmp
snp_fp_adjacency
snp_fp_fragment
snp_fp_tracer_drop
snp_ifc_stat
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: allow
04-23-2014 10:42 PM
I see this in the output when you pinged from inside interface of the ASA:
#pkts encaps: 5, #pkts encrypt: 5, #pkts digest: 5
#pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
#pkts compressed: 0, #pkts decompressed: 0
i.e. the traffic is getting encrypted when traffic is going from the ASA to the client. Also, I see that in Packet tracer command output, everything is being permitted :
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: allow
Please share your IPSec client version. Make sure that you are using latest version of IPsec VPN Client.
Also, when you ping from the VPN client machine, open vpn client and press (cntrl+s) and you will be able to see if packets are getting encrypted or not.
If this does not work then you will have to tunnelall your traffic and internet access should be given through the ASA.
Vishnu
04-24-2014 01:14 PM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide