06-10-2002 03:25 AM - edited 02-21-2020 11:47 AM
i have a vpn between router A & router B.
the machines of site A are connected has through a PIX 515.
I have 3 segment in site B : 20.x.x.x, 10.128.13.x and 10.128.20.x which accedent to the network 10.3.1.x in site A.
i can't ping 10.3.1.x from site B without initiate a ping from site A.
sh run:
crypto isakmp policy 10
hash md5
authentication pre-share
crypto isakmp key dialvpn address 10.3.0.9
!
!
crypto ipsec transform-set dialyset esp-des
mode transport
!
crypto map dialymap local-address Tunnel0
crypto map dialymap 10 ipsec-isakmp
set peer 10.3.0.9
set transform-set dialyset
match address 101
!
!
!
!
interface Loopback0
ip address X.X.X.X
!
interface Tunnel0
bandwidth 10000
backup delay 5 5
backup interface Dialer2
ip address 10.3.0.10 255.255.255.252
keepalive 5 3
tunnel source X.X.X.X
tunnel destination Y.Y.Y.Y
crypto map dialymap
!
interface BRI0
description connected to Internet
no ip address
ip nat outside
encapsulation ppp
dialer pool-member 1
dialer pool-member 2
isdn switch-type basic-net3
no cdp enable
crypto map dialymap
!
interface FastEthernet0
description connected to EthernetLAN
ip address 10.1.2.1 255.255.255.0
ip nat inside
speed auto
half-duplex
no cdp enable
!
interface Serial0
bandwidth 64
ip address 10.1.100.2 255.255.255.252
no fair-queue
crypto map dialymap
!
interface Serial1
ip address 11.11.11.2 255.255.255.252
ip nat outside
no cdp enable
!
interface Dialer1
description connected to Internet
ip address 10.200.2.104 255.255.0.0
ip nat outside
encapsulation ppp
no ip split-horizon
dialer pool 1
dialer idle-timeout 20
dialer hold-queue 10
dialer-group 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname ditech
ppp chap password 7 -- moderator edit --
ppp pap sent-username -- moderator edit -- password 7 -- moderator edit --
crypto map dialymap
!
interface Dialer2
ip address 10.3.0.14 255.255.255.252
encapsulation ppp
dialer pool 2
dialer idle-timeout 86400
dialer-group 1
ppp authentication chap
ppp chap hostname dialy
ppp chap password 7 -- moderator edit --
!
ip nat inside source static 10.1.2.8 131.107.0.23 extendable
ip classless
ip route 0.0.0.0 0.0.0.0 Serial0
ip route 0.0.0.0 0.0.0.0 Dialer1 150
ip route 10.3.1.0 255.255.255.240 10.1.2.32
ip route 20.1.1.0 255.255.255.0 10.3.0.9
ip route 20.1.1.0 255.255.255.0 Dialer2
ip route 10.128.13.13 255.255.255.255 10.3.0.9
ip route 10.128.13.13 255.255.255.255 Dialer2
ip route 10.128.20.21 255.255.255.255 10.3.0.9
ip route 10.128.20.21 255.255.255.255 Dialer2
no ip http server
ip http port 12337
ip pim bidir-enable
!
!
access-list 101 permit ip 10.3.1.0 0.0.0.15 20.1.1.0 0.0.0.255
access-list 101 permit ip 10.3.1.0 0.0.0.15 10.128.20.0 0.0.0.255
access-list 101 permit ip 10.3.1.0 0.0.0.15 10.128.23.0 0.0.0.255
access-list 101 permit ip 10.3.1.0 0.0.0.15 host 10.128.20.21
access-list 101 permit ip 10.3.1.0 0.0.0.15 host 10.128.13.13
06-15-2002 02:39 PM
Often times complex configuration/troubleshooting issues are best addressed in an interactive session with one of our trained technical assistance engineers. While other forum users may be able to help, its often difficult to do so for this type of issue.
To utilize the resources at our Technical Assistance Center, please visit http://www.cisco.com/tac and to open a case with one of our TAC engineers, visit http://www.cisco.com/tac/caseopen
If anyone else in the forum has some advice, please reply to this thread.
Thank you for posting.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide