In Location Appliance Version 2.0.x The applications that provide Telnet service are installed on the Location Appliance, but are not enabled by default. SSH service is installed, as well, and is usually enabled by default, which makes the Location Appliance SSH accessible once it is addressed over the console session, and IP accessible. Refer to Installation and Configuration Guide for more information.
In Location Appliance Version 2.1.x:
Note: SSHv1 is no longer supported on location appliances that run version 2.1.x. You need to use a SSHv2 client.
You need to do this configuration during the setup in order to enable the SSHV2 on the location appliance.
Remote root login is currently disabled.
Configure remote root access? (Y)es/(S)kip/(U)se default [Yes] In order to enable root login over secure shell for this machine, choose Yes. This allows a root login both from the console and the SSH. Otherwise, choose Skip. If you choose to leave remote root login disabled, then a root login can only occur from the console.
Enable remote root login (yes/no) [no] Choose Yes in order to allow remote login through SSH in addition to console login. Choose No in order to allow root login only from the console. Once that is enabled, you can use SSHv2 in order to access the IP address of the Ethernet port on the server.
You can login with the use of the root and run the /opt/locserver/setup/setup.sh in order to rerun the setup script at any time in order to change the settings.
Refer to these notes for more detailed information:
The setup script generates a log file that can be found at /opt/locserver/logs/setup.sh.
There is no way to turn Telnet access on and it is not enabled.
Location services are anchored on time synchronization across the network. If there is an NTP server or relay that is in-house, it is in the best interest of location services if all the controllers and the Location Appliance are configured to synchronize with it. Ensure that the timezones are accurately set across all controllers and the Location Appliance as well. Recall that US timezones are negative (-) offsets from UTC; eastern European timezones are positive (+).
The adjustment of the timezone takes 12 to 24 hours in order to take full effect, so the APs that exist ideally do not have a problem. When there are future conversions of AP to LWAPP, make sure that the PC that hosts the Upgrade Tool is in synchronization with the NTP server and that it has the timezone set correctly. Typically, the perception of time of the PC is the basis with which the Upgrade Tool uses to build the SSC. In addition, a number of those time based problems are resolved in the Upgrade Tool 2.01, so if that version is used and the time is synchronized, it is unlikely that there is a problem in the future.
We are a very small rural K-12 school district with a single building and a deployment of 50 3802i APs and a 5520 controller. This year due to coronavirus we have very suddenly gone 1-to-1 and the wifi is of course being pounded. We do not have the b...
I have a client with AP 1552H for Hazardous environments, and 5508 WLCs, and now he needs new APs for hazardous environments, but 1552H are EoS, so the only available model is the IW6300 but it's only supported in software 184.108.40.206, and the 5508 WLC onl...
WLC4402/4404 firmware images? This WLC is EOL and thus images are no longer available from Cisco. My lab WLC has 7.0.240 code and was hoping you may have something newer. I got my hands on a couple of 3600 series APs for my lab, but this AP is only suppor...
Hey all, I am working with a Cisco 8540 Wireless Controller. I am using radio profiles to roll out settings changes to AP groups (Wireless > RF Profiles, applied at WLANs > Advanced > AP Groups). I have two DCA options in the Radio Profile &...
Hi everyone,In AireOS WLC, we used be modify the Wireless Option "Client Roaming" parameters for solving some client's roming problem. But after migration to C9800 , the Wireless Option "Client Roaming" is gone .My question is:1/ Is ...