04-28-2015 03:55 AM - edited 11-18-2020 03:10 AM
Final code 8.0.120.0 now posted in CCO, thanks for your interest.
8.0.115.30 | |
CSCuq90632 | 3702 crashed with a traceback |
CSCuu81895 | New 1572 out of box AP in local mode not starting CAPWAP process |
8.0.115.26 | |
CSCuu37077 | 3600P limited channels/power similar to CSCus35411 |
CSCuu20683 | RAP might lose the Native VLAN configuration on downgrade from 8.1 |
CSCuu20256 | Traffic drop on WLCs with 7.6.130.206 and PMIPv6 |
CSCut05252 | OEAP: Auth rejected because of challenge failure ReasonCode: 15 |
CSCut47761 | PMIPv6 Client crash with .1x auth when user name have colon ':' |
8.0.115.18 | |
CSCun56310 | #LWAPP-3-VENDOR_PLD_VALIDATE_ERR: SPAM_VENDOR_SPECIFIC_PAYLOAD(185) |
CSCus44831 | 1702 AP reports power error with 802.3af power source |
CSCus25256 | 1130 Flexconnect APs sometimes lose bridge-group configuration |
CSCuq97914 | PI 1.4 cannot finish auditing WLC |
CSCus26067 | HA failing after upgrade to 8.0 due to gateway ARP source mac |
CSCus72994 | WLC Crash on Task Name:DHCP Socket Task |
CSCus94968 | osapiMalloc accepting negative size buffers |
CSCut98741 | WLC Monitor page needs to support session timeout |
CSCut14210 | Flexconnect arp-cache enabled - AP is not responding on behalf of client |
CSCus30769 | BSSID containing itself and also adding itself to client exclusion list. |
CSCuq86269 | DFS detection due to broadcom spurious emissions |
8.0.115.11 | |
CSCus48787 | AP:Radio d1 reset: FW: vec=36 pc=10FC4, irq/mac stat=20000/80 |
CSCur53041 | DTLS connection failure. |
CSCus39358 | Apple and Android not connecting to WPA2-AES on OEAP600 8.0.110 |
CSCus44802 | WLAN NAS-id is not applied when AP Group NAS-id is changed |
CSCus06920 | preauth bit set in RSN IE when wlan is wpa2AES |
CSCut96026 | SGT remains for client when moving between WLANs with Fast SSID change |
CSCuq48218 | WLC cannot process multiple sub-attributes in single RADIUS VSA |
CSCur45862 | AP's cannot discover wlc through option 43 on build 8.0.100 |
CSCuq09859 | APs sending GARP and ARP requests aprox every 2 seconds. |
CSCuq48800 | Low throughput due to UAPSD for Intel 7260 WiFi chipset |
CSCuo09947 | RADIUS AVP #44 (Acct-Session-ID) to be sent in RADIUS authen messages |
CSCuq48218 | WLC cannot process multiple sub-attributes in single RADIUS VSA |
CSCur45453 | web Gui 8500 new mobility support and SPG configuration to be blocked |
CSCur56576 | WLC doesn't support 802.11a for Qatar |
CSCur92472 | PMIPv6: Roaming WLC1->WLC2 don't work, wrong handoff indicator |
CSCus31292 | Oct 2014 OpenSSL Vulnerabilities |
CSCus85767 | Flex local switch clients, local dhcp are trying to do central dhcp |
CSCut45950 | MARCH 2015 OpenSSL Vulnerabilitiess |
8.0.115.7 | |
CSCus45806 | Enable CDP Spare pair TLV for 1570 and 1530 series access points |
CSCur22714 | Ap3602 trying to contain its own RM3000AC module |
CSCut26137 | 3702 - Voice Queue stuck, with no new clients able to associate. |
CSCur37475 | wism2 system crash - at client stats AVL corruption |
CSCus13594 | slow in getting the DHCP address in the AP2700 |
CSCur78697 | 1st Hop MAP CAPWAP Restart Due to race condition when seeking RAP2 |
CSCur72287 | EAPOL Security error seen when 1st HOP MAP Roams from RAP1 to RAP2 |
CSCus48452 | MAPs do not return to configured channel along with RAP 30 after DFS |
CSCus49126 | AP3702 floods RTS frames @ 8000pps to departed client |
CSCuq99230 | AP syslog fails due to default setting 'logging server-arp' |
CSCus85337 | CAPWAP Restart & Gteway not reachable when MAP roams From RAP1 to RAP2 |
CSCuq48043 | IPv6 forwarding halts; broadcast queue full |
CSCur52246 | PMIPv6 GRE key databse gets full during scale testing |
CSCur71427 | Flex: Client roaming fails "not processing DOT1X_4WAY_COMPLETED_AT_AP" |
CSCur74954 | central auth + local switching : clients are in idle state always |
CSCus80059 | WLC always send authen packet to aaa server even no any client in WLC |
CSCut31679 | Kernel panic -Unhandled kernel unaligned access |
8.0.115.3 | |
CSCuq60042 | Memory leak on WLC when using PMIPv6 clients pem_api.c |
CSCuq63642 | Internal webpage appears after successful redirect to external webauth |
CSCur00288 | 8.0.100.0 client is shown with "ip address unknown" and "dhcp required" |
CSCur30298 | 8500 new mobility support for guest anchor and block spg config |
CSCur50819 | BEAST Vulnerability not properly resolved in Cisco WLCs |
CSCur67701 | Image download errors for CAPWAP 7500/8500 |
CSCus39461 | Radius DNS adds both Network and Management Auth + Acct = Enabled |
CSCus46861 | LIZRD attack : Denial of Service |
CSCus64073 | 1700/2700 APs native vlan field missing in Flex tab |
CSCut07617 | Signal 11 crash at PMIPV6_Thread_1 |
CSCut26403 | AP1242 does not forward SIP INVITE when SIP-CAC is enabled |
8.0.115.2 | |
CSCus87673 | 3700 AP 5ghz Radio Reset |
CSCur88864 | 3600 APs with AC module shows 100% Rx utilization on slot-2. |
CSCur23656 | Cisco IOS and IOSd in IOS-XE : evaluation of SSLv3 POODLE vulnerability |
CSCuq19142 | LAP/WLC MIC lifetime expiration causes DTLS failure |
CSCuq54548 | Anchor Memory Leak when Sleeping Client Feature is enabled |
CSCuq74491 | WLC 8.0.100.0 crashes due to Task Name: apfRogueTask_0 |
CSCur20154 | HA SSO pair memory leak |
CSCur96221 | Standby WLC crash at haSSOServiceTask6 |
CSCus21276 | Kernel Panic on wism2 for 8.0MR1 beta |
CSCus38268 | Memory Leak on WiSM2 due to SNMPTask on 7.4.121.0 |
CSCus42727 | JANUARY 2015 OpenSSL Vulnerabilities |
CSCus55004 | WLC2504 8.0MR1: Kernel Panic with pre-auth ACL and external web-redirect |
Hi
it as posted yesterday
regards
hi Nilay
I would recommend 8.0.120.0, as it carries over most of the 8.0Esc fixes. if you want "tried and tested" code, 8.0.110.14 or .16 would be code that has been exposed to large different environments/customers
regards
Thanks Javier,
How do I download 8.0.110.16 code?
I have seen compatibility matrix for 8.1 AirOs and it shows certain IOS requires on access points.
Is that the case and if so Do I have to upgrade it to all the access points including 1142 ?
Kind Regards,
Nilay Vyas.
hi
8.0.110.x is available through a TAC case
you don't need to upgrade the APs beforehand, if you are on the supported upgrade path
(for 8.0, it is 7.0.98.0 and higher, it is detailed on the release notes)
regards
Try using the old stable release unless new version proven to be bug free before doing proper upgrade to your LAPs.
Javier-
So is the 8.0.120.0 (ED) that is on the web site considered the to be 8.0 MR2? Is this the recommended load to go with if we want something stable right now that needs to be Rls 8?
I need to move something Rls 8 into my lab for testing and deployment in August. I haven't heard of an 8.0 MR3 in the works.
thanks
Hi
>So is the 8.0.120.0 (ED) that is on the web site considered the to be 8.0 MR2?
yes
> I haven't heard of an 8.0 MR3 in the works.
it is already on planning phase
regards
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: