Problema al convertir Cisco AP 2802i en ME (WLC)

[JVelasco]

Hola chicos, estoy volviendome un poco loco, controlo algo de router y switches Cisco, pero con los APs estoy ahora empezando a trastear. Ha caido en mis manos varios AP 2802i y quiero convertir uno de ellos en Mobility Express para que me haga de WLC del resto.

El caso es que he pasado del software CAPWAP a Mobility Express pero algo me da que no está bien, porque primero que se me queda la luz parpadeando alternando verde y rojo, que según este enlace el punto se encuentra en proceso de descubrir/unirse a un WLC, de hecho veo mensajes en consola de este tipo:

[*12/21/2023 14:54:55.7946] CAPWAP State: Discovery
[*12/21/2023 14:54:55.7953] IP DNS query for CISCO-CAPWAP-CONTROLLER.xxxxxx.ddns.net
[*12/21/2023 14:54:55.9374] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*12/21/2023 14:54:55.9393] Discovery Response from 192.168.1.99
[*12/21/2023 14:55:05.0003] CAPWAP State: DTLS Setup
[*12/21/2023 14:56:02.0359]
[*12/21/2023 14:56:02.0359] CAPWAP State: DTLS Teardown
[*12/21/2023 14:56:02.1073] upgrade.sh: Script called with args:[ABORT]
[*12/21/2023 14:56:02.1632] do ABORT, part2 is active part
[*12/21/2023 14:56:02.1836] upgrade.sh: Cleanup tmp files ...
[*12/21/2023 14:56:02.2113] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*12/21/2023 14:56:02.2148] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*12/21/2023 14:56:06.7875] No more AP manager addresses remain..
[*12/21/2023 14:56:06.7875] No valid AP manager found for controller 'VODAFONE' (ip: 192.168.1.99)
[*12/21/2023 14:56:06.7876] Failed to join controller VODAFONE.
[*12/21/2023 14:56:06.7876] Failed to join controller.

Curiosamente mi red es la 192.168.2.x, no sé si es que está descubriendo datos de algún otro controlador cercano.

Yo realicé todo el proceso de factory reset, apretando el botón más de 20 segundos en el arranque y de hecho el show versión muestra lo siguiente:

cisco AIR-AP2802I-E-K9 ARMv7 Processor rev 1 (v7l) with 1028260/465764K bytes of memory.
Processor board ID FGL2049A2BH
AP Running Image     : 8.10.142.0
Primary Boot Image   : 8.10.142.0
Backup Boot Image    : 8.9.111.0
Primary Boot Image Hash: 0c8801d491d51cd6c9642eae26aa5c53fbe548b2c036d0b1e7b7c125f94a8613287eb2ebe46903dfac29c1b4e5cd104843ec520d25c43b0943b330c9f0fd78bc
Backup  Boot Image Hash: 5a93e979a0dfd024b15c6f9fd566a4e95087b1353d9065d5ea1419d81dfe12168260c03db7f1da93013b403d35260f775211b42d4ef09748417a36450fcddb7f
AP Image type    : MOBILITY EXPRESS IMAGE
AP Configuration : MOBILITY EXPRESS CAPABLE
2 Gigabit Ethernet interfaces
2 802.11 Radios
Radio Driver version : 9.0.5.5-W8964
Radio FW version : 9.1.8.1
NSS FW version : 2.4.28

Base ethernet MAC Address            : CC:16:7E:DC:11:1A
Part Number                          : 73-100821-03
PCA Assembly Number                  : 000-00000-00
PCA Revision Number                  :
PCB Serial Number                    : FDO20441BBH
Top Assembly Part Number             : 068-100534-01
Top Assembly Serial Number           : FGL2049A2BH
Top Revision Number                  : A0
Product/Model Number                 : AIR-AP2802I-E-K9

El caso es que ni puedo conectarme por wifi para hacer la configuración, ni en consola me lanza el setup inicial. ¿podéis darme alguna pista o alguna indicación sobre como proceder? He estado viendo múltiples hilos de la comunidad y también en algunas webs, de problemas con la alimentación o con la actualización de la imagen del sistema, pero creo haber seguido todo correctamente, aunque supongo que algo haré mal.

El AP recibe la IP por dhcp 192.168.2.203 y responde a ping, pero no a telnet, http o ssh, y tampoco publica ninguna wifi ni la aprovisionamiento.

Os adjunto el arranque por si os da alguna pista del problema:

Button is pressed. Configuration reset activated..
Keep the button pressed for > 20 seconds for full factory reset

Wait for the button to be released ....
Button pressed for  23 seconds

Performing full factory reset..


Setting env for full reset..
SF: Detected N25Q32A with page size 64 KiB, total 4 MiB
Erasing SPI flash....Writing to SPI flash.....done
do_resetb
do_clear fips env


Setting env for configuration reset..
Erasing SPI flash....Writing to SPI flash.....done
do_format_storage
Creating 1 MTD partitions on "nand0":
0x000000200000-0x000010000000 : "mtd=2"
UBI: attaching mtd1 to ubi0
Remove UBI volume storage (id 5)
No size specified -> Using max size (68694016)
Creating dynamic volume storage of size 68694016
reset u-boot
resetting ...

BootROM - 1.78
Booting from SPI flash, Secure mode
BootROM: RSA Public key verification PASSED
BootROM: CSK block signature verification PASSED
BootROM: Boot header signature verification PASSED
BootROM: Box ID verification PASSED
BootROM: JTAG is disabled


General initialization - Version: 1.0.0
Detected Device ID 6920
Master bootloder version 1.44
High speed PHY - Version: 2.0
BoardId = 0x21board SerDes lanes topology details:
 | Lane # | Speed|    Type     |
 ------------------------------|
 |   1    |  0   |  SGMII1     |
 |   2    |  5   |  PCIe1      |
 |   4    |  5   |  PCIe2      |
 |   5    |  0   |  SGMII2     |
 -------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 1: Link upgraded to Gen2 based on client cpabilities
:** Link is Gen1, check the EP capability
PCIe, Idx 2: Link upgraded to Gen2 based on client cpabilities
High speed PHY - Ended Successfully
DDR4 Training Sequence - Ver TIP-0.23.(Sublib 0.8)0
DDR4 Training Sequence - Switching XBAR Window to FastPath Window
DDR4 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
BootROM: Boot image signature verification PASSED

  ____  _
 / ___|(_) ___   ___  ___
| |    | |/ __| / __|/ _ \
| |___ | |\__ \| (__| (_) |
 \____||_||___/ \___|\___/
         _   _     ____              _
        | | | |   | __ )  ___   ___ | |_
        | | | |___|  _ \ / _ \ / _ \| __|
        | |_| |___| |_) | (_) | (_) | |_
         \___/    |____/ \___/ \___/ \__|
 ** LOADER **


U-Boot 2013.01-g2ee3a18aa (Jun 03 2022 - 11:27:17) SDK version: 2015_T2.0p10

Board: Barbados-2K
SoC:   MV88F6920 Rev A1
       running 2 CPUs
CPU:   ARM Cortex A9 MPCore (Rev 1) LE
       CPU 0
       CPU    @ 1800 [MHz]
       L2     @ 900 [MHz]
       TClock @ 250 [MHz]
       DDR4    @ 900 [MHz]
       DDR4 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM:  1 GiB

RST I2C0
NAND:  ECC 4bits, 256 MiB
SF: Detected N25Q32A with page size 64 KiB, total 4 MiB
PCI-e 1 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0
PCI-e 2 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 2.0

Map:   Code:                    0x3fed8000:0x3ffae448
       BSS:                     0x3ffeff0c
       Stack:                   0x3f9c7f20
       Heap:                    0x3f9c8000:0x3fed8000
       U-Boot Environment:      0x00100000:0x00110000 (SPI)

Board configuration:
|  port  | Interface  | PHY address  |
|--------|------------|--------------|
| egiga1 |   SGMII    |     0x01     |
| egiga2 |   SGMII    |     0x00     |
Net:   , egiga1, egiga2 [PRIME]
Hit ESC key to stop autoboot:  0
Creating 1 MTD partitions on "nand0":
0x000000200000-0x000010000000 : "mtd=2"
UBI: attaching mtd1 to ubi0
UBIFS: mounted UBI device 0, volume 1, name "part2"
Loading file 'part2/part.bin' to addr 0x02000000 with size 6332465 (0x0060a031)...
Done
SF: Detected N25Q32A with page size 64 KiB, total 4 MiB

Checking image signing.
Image signing verification success, continue to run...
## Booting kernel from Legacy Image at 02000000 ...
   Image Name:   Barbados Firmware Image
   Created:      2020-11-04  16:10:17 UTC
   Image Type:   ARM Linux Multi-File Image (uncompressed)
   Data Size:    6331457 Bytes = 6 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Contents:
      Image 0: 4203368 Bytes = 4 MiB
      Image 1: 2111936 Bytes = 2 MiB
      Image 2: 16137 Bytes = 15.8 KiB
   Verifying Checksum ... OK
## Loading init Ramdisk from multi component Legacy Image at 02000000 ...
## Flattened Device Tree from multi component Image at 02000000
   Booting using the fdt at 0x02605d78
   Loading Multi-File Image ... OK
OK
   reserving fdt memory region: addr=0 size=4000
   Loading Device Tree to 01ff9000, end 01ffff08 ... OK

   Starting Device Tree update ('fdt_skip_update' = no)

Limit DDR size at 3GB due to power of 2 requirement of Address decoding
Updating device tree successful

Starting kernel ...

[01/01/1970 00:00:00.0000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260096
[01/01/1970 00:00:00.0000] Memory: 1025848K/1048576K available (5743K kernel code, 407K rwdata, 2472K rodata, 359K init, 478K bss, 22728K reserved)
[01/01/1970 00:00:00.1200] CPU1: Booted secondary processor
[01/01/1970 00:00:01.4400] buginf tty flushing thread started, ttyport=bf1acc00
[01/01/1970 00:00:01.5600] m25p80 spi1.0: found n25q032a, expected n25q032
[*07/19/1986 05:01:19.5008] buginf() enabled.
[*07/19/1986 05:01:19.5105] Made it into bootsh: Nov  4 2020 06:57:45 T-a9e4eaf8ccf0cad1ba59eaa8794b7332dbca2d5a-ga9e4eaf8-aut
[*07/19/1986 05:01:29.6669] bootsh mini ramfs booted /bootpart/part2/ramfs_data_cisco.cpio.lzma

Welcome to Cisco.

Usage of this device is governed by Cisco's End User License Agreement,
available at:
http://www.cisco.com/c/en/us/td/docs/general/warranty/English/EU1KEN_.html.


             Restricted Rights Legend

Use, duplication, or disclosure by the Government is subject to
restrictions as set forth in subparagraph (c) of the Commercial
Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and
subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

            Cisco Systems, Inc.
            170 West Tasman Drive
            San Jose, California 95134-1706

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.


This product contains some software licensed under the
"GNU General Public License, version 2" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html


This product contains some software licensed under the
"GNU Library General Public License, version 2" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Library
General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.0.html


This product contains some software licensed under the
"GNU Lesser General Public License, version 2.1" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Lesser
General Public License, version 2.1", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html


This product contains some software licensed under the
"GNU General Public License, version 3" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, Version 3", available here:
http://www.gnu.org/licenses/gpl.html.


This product contains some software licensed under the
"GNU Affero General Public License, version 3" provided
with ABSOLUTELY NO WARRANTY under the terms of
"GNU Affero General Public License, version 3", available here:
http://www.gnu.org/licenses/agpl-3.0.html.

Factory full reset detected...
Full Factory Reset triggered: clear all files from storage..
[*07/19/1986 05:01:55.4578] /init: ioctl(SIOCGIFHWADDR): wired0: No such device
[*07/19/1986 05:01:55.4608] /init: ioctl(SIOCGIFHWADDR): wired0: No such device
[  OK  ] Reached target Timers.
[  OK  ] Created slice -.slice.
[  OK  ] Listening on udev Kernel Socket.
[  OK  ] Listening on Delayed Shutdown Socket.
[  OK  ] Created slice system.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
[  OK  ] Reached target Slices.
         Starting Cisco UBIFS reformat/mount...
[  OK  ] Reached target Cisco File Systems (Pre).
[  OK  ] Listening on udev Control Socket.
[  OK  ] Reached target Sockets.
         Starting udev Kernel Device Manager...
         Starting udev Coldplug all Devices...
[  OK  ] Started udev Kernel Device Manager.
[  OK  ] Started Cisco UBIFS reformat/mount.
         Starting Cisco early mount...
[  OK  ] Started Cisco early mount.
[  OK  ] Reached target Local File Systems (Pre).
         Starting Cisco platform file generation...
         Starting Cisco fips check...
         Starting Cisco seed generation...
         Starting Cisco system time setup...
[  OK  ] Started Cisco system time setup.
[  OK  ] Started Cisco seed generation.
[  OK  ] Started Cisco fips check.
[  OK  ] Started Cisco platform file generation.
         Starting Cisco btldr service...
[  OK  ] Started udev Coldplug all Devices.
[  OK  ] Started Cisco btldr service.
[  OK  ] Reached target Local File Systems.
         Starting Cisco S10 boot service...
[  OK  ] Started Cisco system time saving.
         Starting Cisco system time saving...
[*10/29/2016 23:59:59.0525] Manufacturing time is: Oct 29 23:59:59 2016
[*10/29/2016 23:59:59.0526] Storing the manufacturing time in reload time as the reload time stamp was not present
[*10/29/2016 23:59:59.0081] Setting system time Sat Oct 29 23:59:59 UTC 2016
[*10/30/2016 00:00:00.1094] GCM-128 POST passed
[*10/30/2016 00:00:00.1094] GCM-256 POST passed
[*10/30/2016 00:00:03.3137] 0
[*10/30/2016 00:00:03.4777] Active version: 8.10.142.0
[*10/30/2016 00:00:03.4803] Backup version: 0.0.0.0
[*10/30/2016 00:0[10/30/2016 00:00:03.8600] PCI: enabling device 0000:00:02.0 (0140 -> 0143)
0:03.6687] devic[10/30/2016 00:00:03.9600] PCI: enabling device 0000:02:00.0 (0140 -> 0142)
e wired0 entered promiscuous mode
[*10/30/2016 00:00:04.0664] wifi0: Initializing TX ring
[*10/30/2016 00:00:04.0698] wifi0: Initializing RX ring
[*10/30/2016 00:00:04.0743] wifi0: prepare firmware downloading
         Starting Security Auditing Service...
[*10/30/2016 00:00:04.3144] parameter passed without an option given
         Starting Cisco pkg install service...
         Starting Cisco act2 check...
[  OK  ] Started Security Auditing Service.
[  OK  ] Started Cisco pkg install service.
[*10/30/2016 00:00:04.8928] wifi0: Firmware downloading
[*10/30/2016 00:00:06.3830] 0;0;
[*10/30/2016 0[10/30/2016 00:00:10.5100] PCI: enabling device 0000:00:03.0 (0140 -> 0143)
[10/30/2016 00:00:10.5900] PCI: enabling device 0000:03:00.0 (0140 -> 0142)
[  OK  ] Started Cisco act2 check.
[  OK  ] Started Cisco S10 boot service.
         Starting Cisco nss service...
<30>systemd[1]: Started Cisco pkg install service.
[*10/30/2016 00:00:08.6626] 0;Reading AC         Starting Cisco watchdog...
         Starting Cisco nolan service...
[  OK  ] Started Cisco watchdog.
[  OK  ] Started Cisco nolan service.
         Starting Cisco nolan USB service...
[  OK  ] Started Cisco nolan USB service.
[  OK  ] Started Cisco pre-PoE negotiation.
         Starting Cisco pre-PoE negotiation...
[  OK  ] Started Cisco nss service.
         Starting Cisco S15platform...
         Starting Cisco Kclick...
[10/30/2016 00:00:20.7000] Disabling lock debugging due to kernel taint
[  OK  ] Started Cisco S15platform.
[  OK  ] Started Cisco Kclick.
         Starting Cisco certificate create service...
         Starting Cisco Sku service...
[*10/30/2016 00:00:20.9008] stile module dp init successfully
[*10/30/2016 00:00:20.9009] NBAR Label:BLD_POLARIS_DEV_LATEST_20200414_053707 Module timestamp: Nov  4 2020 at 06:45:09 User: ttaichol
[*10/30/2016 00:00:23.3270] SKU to radio FW
[*10/30/2016 00:00:23.3820] wifi2     no private ioctls.
[*10/30/2016 00:00:23.3820]
         Starting Cisco ME service...
         Starting Cisco Kclick...
[*10/30/2016 00:00:23.7825] grep: /storage/config.mobexp: No such file or directory
[*10/30/2016 00:00:23.7977]  Create symlink /dev/mic_cert result 0
[*10/30/2016 00:00:23.7977] Loading certificates from storage...
[*10/30/2016 00:00:23.8413] barbados /tmp/SC4_1dbm.txt
[  OK  ] Started Cisco certificate create service.
[  OK  ] Started Cisco Sku service.
[  OK  ] Started Cisco Tam service.
         Starting Cisco Tam service...
         Starting Cisco certtime service...
[  OK  ] Started Cisco ME service.
[10/30/2016 00:00:24.4600] xt_CONNSECMARK: Unknown symbol nf_ct_l3proto_module_put (err 0)
[10/30/2016 00:00:24.5600] xt_CONNSECMARK: Unknown symbol xt_register_target (err 0)
[10/30/2016 00:00:24.6500] xt_CONNSECMARK: Unknown symbol nf_ct_l3proto_try_module_get (err 0)
[10/30/2016 00:00:24.7500] xt_CONNSECMARK: Unknown symbol xt_unregister_target (err 0)
[10/30/2016 00:00:24.8700] xt_SECMARK: Unknown symbol xt_register_target (err 0)
[10/30/2016 00:00:24.9600] xt_SECMARK: Unknown symbol xt_unregister_target (err 0)
[  OK  ] Started Cisco Kclick.
         Starting Cisco syslog service...
[*10/30/2016 00:00:25.0831] /etc/init.d/S16mod_load: line 98: can't create /storage/syslogs/1.modlog: nonexistent directory
[*10/30/2016 00:00:25.1444] Creating default base capwap config.
         Starting rsyslog client...
         Starting Cisco S16platfomm...
[  OK  ] Started Cisco syslog service.
[  OK  ] Started rsyslog client.
[  OK  ] Started Cisco S16platfomm.
         Starting Cisco synclogd...
[  OK  ] Started Cisco synclogd.
[  OK  ] Started Cisco certtime service.
[  OK  ] Reached target System Initialization.
[*10/30/2016 00:00:30.1003] starting tam services using ACT2...
[*10/30/2016 00:00:30.1003]
[[  OK  ] Reached target Paths.
[  OK  ] Reached target Basic System.
[  OK  ] Started NTP_PROC daemon.
         Starting NTP_PROC daemon...
         Starting AP Trace daemon...
         Starting Cisco rtd service...
         Starting Marvell Forwarding daemon...
         Starting gRPC server daemon...
         Starting Cisco printkd...
         Starting Cisco kexec...
         Starting Hostapd process...
         Starting Cisco klogd...
         Starting WCPD process...
         Starting OpenSSH server daemon...
[  OK  ] Started System Monitor service.
         Starting System Monitor service...
         Starting Cisco image/firmware updater service...
         Starting Cisco brain service...
[  OK  ] Started Serial Getty on ttyS0.
         Starting Serial Getty on ttyS0...
[  OK  ] Reached target Login Prompts.
         Starting capwapd...
         Starting Clean Air daemon...
         Starting Cisco led service...
         Starting Fast CGI daemon...
[  OK  ] Started Cisco kexec.
[  OK  ] Started Cisco image/firmware updater service.
[  OK  ] Started Cisco printkd.
[  OK  ] Started Cisco klogd.
[  OK  ] Started AP Trace daemon.
[  OK  ] Started Cisco rtd service.
[  OK  ] Started Fast CGI daemon.
[  OK  ] Started Hostapd process.
[  OK  ] Started Cisco led service.
[  OK  ] Started Cisco brain service.
[10/30/2016 00:00:33.3100] wired0 emac 2: link up
[10/30/2016 00:00:33.3700] wired0: link up



User Access Verification
Username: [10/30/2016 00:00:43.5200] wired0 emac 2: link up
[10/30/2016 00:00:43.5700] wired0: link up
[*10/30/2016 00:00:43.8559]
[*10/30/2016 00:00:43.8559] !!!!! {/opt/cisco/bin/capwap_brain} failed writing /click/vrrp_elector/preferred_ap_name len 0 data: ""
[*10/30/2016 00:00:44.2663] ip6_port srcr2, ip6local fe80::ce16:7eff:fedc:111a, ip6 ::, plen 0, gw6 ::, gw6_mac 00:00:00:00:00:00, mtu 1500, vid 0, mode6 2(slaac)
[*10/30/2016 00:00:44.9578] pid 7396's current affinity mask: 3
[*10/30/2016 00:00:44.9578] pid 7396's new affinity mask: 1
[*10/30/2016 00:00:45.5810] device aptrace0 entered promiscuous mode
[*10/30/2016 00:00:45.6352] device to_container entered promiscuous mode
[*10/30/2016 00:00:46.5596] chpasswd: password for user changed
[*10/30/2016 00:00:47.8739] DOT11_TXP[0]:Domain configured: 12 class:E
[*10/30/2016 00:00:48.3257] DOT11_TXP[0]:Domain configured: 1 class:E
[*10/30/2016 00:00:48.4087] DOT11_TXP[0]:Domain configured: 12 class:E
[*10/30/2016 00:00:48.4968] USB Device Disconnected from the AP
[*10/30/2016 00:00:48.8598] DOT11_TXP[0]:Domain configured: 1 class:E
[*10/30/2016 00:00:48.9560] DOT11_TXP[2]:Domain configured: 12 class:E
[*10/30/2016 00:00:50.6455] DOT11_DRV[0]: Stopped Radio 0
[*10/30/2016 00:00:50.7069] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 6
[*10/30/2016 00:00:51.5252]
[*10/30/2016 00:00:51.5252] !!!!! {/opt/cisco/bin/capwap_brain} failed writing /click/vrrp_elector/preferred_ap_name len 0 data: ""
[*10/30/2016 00:00:51.5858] ethernet_port wired0, ip 192.168.2.203, netmask 255.255.255.0, gw 192.168.2.2, mtu 1500, bcast 192.168.2.255, dns1 8.8.8.8, dns2 62.42.63.52, domain xxxxx.ddns.net, vid 0, static_ip_failover false, dhcp_vlan_failover false
[*10/30/2016 00:00:52.5466] DOT11_DRV[1]: Stopped Radio 1
[*10/30/2016 00:00:52.5738] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*10/30/2016 00:00:53.7687] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 1
[*10/30/2016 00:00:54.4139] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 1
[*10/30/2016 00:00:54.4343] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 1
[*10/30/2016 00:00:55.4281] bftype is 6
[*10/30/2016 00:00:55.4549] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 1
[*10/30/2016 00:00:56.2271] DOT11_DRV[0]: DOT11_DRV[0]: set_channel Channel set to 1
[*10/30/2016 00:00:56.3916] failed wlconfig_commit netdev = wifi1
[*10/30/2016 00:00:56.3916] Error for wireless request "Commit changes" (8B00) :
[*10/30/2016 00:00:56.3917]     SET failed on device wifi1 ; Operation not permitted.
[*10/30/2016 00:00:56.7422] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*10/30/2016 00:00:57.5829] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*10/30/2016 00:00:58.2213] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*10/30/2016 00:00:58.2417] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*10/30/2016 00:00:59.3530] bftype is 6
[*10/30/2016 00:00:59.3796] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*10/30/2016 00:01:00.2424] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*10/30/2016 00:01:01.1066] DOT11_DRV[1]: DOT11_DRV[1]: set_channel Channel set to 36
[*10/30/2016 00:01:02.4247] VRRP detected external controller. Moving to day1AP IPv4 Address updated from 0.0.0.0 to 192.168.2.203
[*10/30/2016 00:01:14.6996] dtls_init: Use SUDI certificate
[*10/30/2016 00:01:14.7023]
[*10/30/2016 00:01:14.7023] CAPWAP State: Init
[*10/30/2016 00:01:14.7077]
[*10/30/2016 00:01:14.7077] CAPWAP State: Discovery
[*10/30/2016 00:01:14.7084] IP DNS query for CISCO-CAPWAP-CONTROLLER.xxxxx.ddns.net
[*10/30/2016 00:01:14.8176] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*10/30/2016 00:01:14.8180]
[*10/30/2016 00:01:14.8180] CAPWAP State: Discovery
[*10/30/2016 00:01:14.8201] Discovery Response from 192.168.1.99
[*10/30/2016 00:01:19.5205] Start: RPC thread 1951382512 created.
[*12/21/2023 15:07:06.0003]
[*12/21/2023 15:07:06.0003] CAPWAP State: DTLS Setup
[*12/21/2023 15:07:43.4230] systemd[1]: sshd.service start-pre operation timed out. Terminating.
[*12/21/2023 15:07:43.4243] systemd[1]: Failed to start OpenSSH server daemon.
[*12/21/2023 15:07:43.4244] systemd[1]: sshd.service failed.
[*12/21/2023 15:08:03.0417]
[*12/21/2023 15:08:03.0417] CAPWAP State: DTLS Teardown
[*12/21/2023 15:08:03.1565] upgrade.sh: Script called with args:[ABORT]
[*12/21/2023 15:08:03.2214] do ABORT, part2 is active part
[*12/21/2023 15:08:03.2462] upgrade.sh: Cleanup tmp files ...
[*12/21/2023 15:08:03.2738] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*12/21/2023 15:08:03.2739] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*12/21/2023 15:08:07.7931] No more AP manager addresses remain..
[*12/21/2023 15:08:07.7931] No valid AP manager found for controller 'VODAFONE' (ip: 192.168.1.99)
[*12/21/2023 15:08:07.7932] Failed to join controller VODAFONE.
[*12/21/2023 15:08:07.7932] Failed to join controller.
[*12/21/2023 15:08:27.7966]
[*12/21/2023 15:08:27.7966] CAPWAP State: Discovery
[*12/21/2023 15:08:27.8001] IP DNS query for CISCO-CAPWAP-CONTROLLER.xxxxx.ddns.net
[*12/21/2023 15:08:27.9403] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*12/21/2023 15:08:27.9427] Discovery Response from 192.168.1.99
[*12/21/2023 15:08:37.0003]
[*12/21/2023 15:08:37.0003] CAPWAP State: DTLS Setup
[*12/21/2023 15:09:34.0441]
[*12/21/2023 15:09:34.0441] CAPWAP State: DTLS Teardown
[*12/21/2023 15:09:34.1174] upgrade.sh: Script called with args:[ABORT]
[*12/21/2023 15:09:34.1782] do ABORT, part2 is active part
[*12/21/2023 15:09:34.1990] upgrade.sh: Cleanup tmp files ...
[*12/21/2023 15:09:34.2268] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*12/21/2023 15:09:34.2268] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: DTLS Teardown(4).
[*12/21/2023 15:09:38.7924] No more AP manager addresses remain..
[*12/21/2023 15:09:38.7924] No valid AP manager found for controller 'VODAFONE' (ip: 192.168.1.99)
[*12/21/2023 15:09:38.7924] Failed to join controller VODAFONE.
[*12/21/2023 15:09:38.7924] Failed to join controller.

Muchas gracias de antemano.

[JVelasco · Accepted solution]

Resuelto: He caído en quitarle el cable de red del power-injector para que no tuviera conexión a la red y tras volver a conectar el power-injector (pero sin el cable de red) y tras terminar el arranque al poco el solo se ha configurado y ya ha entrado en consola en el modo de aprovisionamiento y autoinstall, tras activar el webserver y los servicios pertinentes, el led se ha quedado fijo en el verde y ya me aparece la red CiscoAirProvision.

Ya podía algún manual concretar esto.

Lo dejo de todos modos por aquí, por si le ocurre a alguna persona más.