请问2960交换机开启ipv6有什么要求吗,是否要哪个高版本ios?
ipv6是否仅支持3层交换机开启路由模式?二层交换机的管理vlan的ip地址能设置为ipv6吗?
64K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 64:D9:89:A7:D8:00
Motherboard assembly number : 73-10015-11
Power supply part number : 341-0098-02
Motherboard serial number : FOC15283A4R
Power supply serial number : AZS15260751
Model revision number : J0
Motherboard revision number : A0
Model number : WS-C2960G-24TC-L
System serial number : FOC1528V5AM
Top Assembly Part Number : 800-26673-07
Top Assembly Revision Number : A0
Version ID : V07
CLEI Code Number : CMMD610ARA
Hardware Board Revision Number : 0x01
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 24 WS-C2960G-24TC-L 12.2(50)SE5 C2960-LANBASEK9-M
已解决! 转到解答。
12.2(50)应该是支持配置IPv6的,不过默认情况下ipv6并未启用,需要手动开启一下
全局模式下配置"sdm prefer dual-ipv4-and-ipv6 default",然后重启交换机,即可使用ipv6,
2960作为基础的二层交换机,支持ipv6的功能也是有限的,接口SVI配置v6地址,配置单播的默认路由还是可以的,其他的就有点鸡肋了。更多的Feature可以参考一下文档:
2960的产品大部分已经EOS了,如果还有在使用的设备,建议将相关的文档下载一些进行留存。
Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ---------- * 1 50 WS-C2960-48TC-L 12.2(50)SE1 C2960-LANBASEK9-M Configuration register is 0xF TEST# TEST#conf t Enter configuration commands, one per line. End with CNTL/Z. TEST(config)#int vlan 1 TEST(config-if)#ipv6 add TEST(config-if)#ipv6 address 2001:1::1/64 TEST(config-if)#exit TEST(config)#ipv6 route ::/0 2001:1::1111 TEST(config)#exit TEST#sh sdm prefer The current template is "dual-ipv4-and-ipv6 default" template. <------------------- The selected template optimizes the resources in the switch to support this level of features for 0 routed interfaces and 255 VLANs. number of unicast mac addresses: 8K number of IPv4 IGMP groups + multicast routes: 0.25K number of IPv4 unicast routes: 0 number of IPv6 multicast groups: 0.375k number of directly-connected IPv6 addresses: 0 number of indirect IPv6 unicast routes: 0 number of IPv4 policy based routing aces: 0 number of IPv4/MAC qos aces: 0.125k number of IPv4/MAC security aces: 0.375k number of IPv6 policy based routing aces: 0 number of IPv6 qos aces: 0 number of IPv6 security aces: 0.125k TEST#
12.2(50)应该是支持配置IPv6的,不过默认情况下ipv6并未启用,需要手动开启一下
全局模式下配置"sdm prefer dual-ipv4-and-ipv6 default",然后重启交换机,即可使用ipv6,
2960作为基础的二层交换机,支持ipv6的功能也是有限的,接口SVI配置v6地址,配置单播的默认路由还是可以的,其他的就有点鸡肋了。更多的Feature可以参考一下文档:
2960的产品大部分已经EOS了,如果还有在使用的设备,建议将相关的文档下载一些进行留存。
Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ---------- * 1 50 WS-C2960-48TC-L 12.2(50)SE1 C2960-LANBASEK9-M Configuration register is 0xF TEST# TEST#conf t Enter configuration commands, one per line. End with CNTL/Z. TEST(config)#int vlan 1 TEST(config-if)#ipv6 add TEST(config-if)#ipv6 address 2001:1::1/64 TEST(config-if)#exit TEST(config)#ipv6 route ::/0 2001:1::1111 TEST(config)#exit TEST#sh sdm prefer The current template is "dual-ipv4-and-ipv6 default" template. <------------------- The selected template optimizes the resources in the switch to support this level of features for 0 routed interfaces and 255 VLANs. number of unicast mac addresses: 8K number of IPv4 IGMP groups + multicast routes: 0.25K number of IPv4 unicast routes: 0 number of IPv6 multicast groups: 0.375k number of directly-connected IPv6 addresses: 0 number of indirect IPv6 unicast routes: 0 number of IPv4 policy based routing aces: 0 number of IPv4/MAC qos aces: 0.125k number of IPv4/MAC security aces: 0.375k number of IPv6 policy based routing aces: 0 number of IPv6 qos aces: 0 number of IPv6 security aces: 0.125k TEST#