Created by: Regan DeDiana on 15-05-2010 05:54:13 PM hey folks, any good examples illustrating the end-to-end requirements of using the tandberg xml api services?
i've found a lot of documentation defining the methods for transmitting and "transceiving" information between clients apps and codecs. specifically using either the "getxml", "putxml", "formputxml" or "Bare-bone http(s)" access mechanisms. most of the documents are clear with the encoding and header requirements, and or the parameter format. but, i'm curious if there are other requirements like "authorization" or authentication that i may be missing?
it's usually helpful to work thru some examples, and i was hoping some might be available somewhere (c# or java).
Subject: RE: TANDBERG XML API service (TXAS) examples Replied by: David Bruun-Lie on 19-05-2010 04:16:14 PM Hi Regan, when it comes to authorization or authentication we are just using standard telnet/ssh/http/https methods and descriptions on how they work are outside the scope of what we document but is easily found by searching on the internet for examples :-)
We do have some java code that I can send you that shows you one suggested implementation though.
Subject: RE: TANDBERG XML API service (TXAS) examples Replied by: Regan DeDiana on 20-05-2010 11:27:35 PM would love to see anything you have, even java ;) (kidding)... please reach out to firstname.lastname@example.org.
much appreciated, thanks Regan
Subject: RE: TANDBERG XML API service (TXAS) examples Replied by: David Bruun-Lie on 21-05-2010 01:10:03 PM Code sent
Subject: RE: TANDBERG XML API service (TXAS) examples Replied by: Bjarte Lunde on 25-05-2010 10:04:22 AM Hi
Could i have a copy too ;)
blunde krollalfa gmail dott com
Subject: RE: TANDBERG XML API service (TXAS) examples Replied by: Anton Van Wyk on 29-06-2010 01:34:27 PM How do you get teh TXAS via HTTP session going...
Subject: RE: TANDBERG XML API service (TXAS) examples Replied by: Frederick Senior on 27-07-2010 07:23:00 PM Hi,
All those comments sounds good and useful for me .. about api programming , please I m newbie on it can you send me same code .
and further, i was trying to connect a call via HTTP.. but it comes out with "401 Authorization error" and a pop-up want my ID/PW..
How can i put my ID (as i do not use passwored) in HTTP command?
many thanks. Sean
Subject: RE: TANDBERG XML API service (TXAS) examples Replied by: David Bruun-Lie on 16-01-2012 10:11:11 AM Sean, regardless of using a password or not you need to authenticate when using the http interface.
Hi All, We are using the WebEx Meetings XML API to retrieve the Recording List. When to try to update the RecordingInfo using SetRecordingInfo API call, we get a 'success'. However, it is not effecting the record result when we login to see the recor...
We have large UC network with numerous CUCM clusters...Dial-plan is variable length and numerous direction presentFor example0782XXX - 8 digit078[013-8]XX - 7 digit0614XXX - 8 digitetc where are more than 300 route patterns We used UCCX...
Hi,I want to dry run failover certification test cases. To test DNS SRV, the test case asks to set SBC FQDN. I couldn't find SBC FQDN in the handbook. Can some one help? Or is it fine, if I will create my own FQDN and test? Thanks,Priyaranjan
Hi, We are able to successfully show the caller's photograph using ECC profile in CUCM (on 88XX series phones and CUCM ver12.5).When we are showing the caller's photograph using CiscoIPPhoneExecute and CiscoIPPhoneImageFile objects, the default ...
Hello, sometimes the handleNewDialog handler is not triggered. I tested it with the clientLogs.log() function. So the handler doesn't do much except output something in the console. But there are calls, where it's not triggered.I noticed when this is...