This document was generated from CDN thread
Created by: Xu Wei on 09-11-2010 11:13:14 AM
Now I'm confuse with the ReqICMLabel element, I use the ReqICMLabel element to pass data to ICM, I'm have try many times, but it's still end with error leg, I don't know where is the problem happened.
My version of CVP is 7.02, version of ICM is 7.3.
In the ICM I configure the IVR to be Type10.
In the routing script, Before RunExt element I set four variable, the first is user.microapp.media_server, the second is user.microapp.app_media_lib,
the thrid is user.microapp.ToExlVXML[0] to be concatenate("application=IDSBGCallCenter;Callid=",Call.user.media.id)
the fourth is user.microapp.UseVXMLParms to be N
Any answer will be greatly appreciated.
By the way, I see the ReqICMLabel cann't work under Comprehensive Call Flow , what's difference between Comprehensive and Standalone with Reporting Server? I can't clearly distinguish them, Can you help me?
Appreciate again!
Subject: RE: About ReqICMLabel
Replied by: Manoj Anantha on 09-11-2010 12:23:09 PM
I should accept the fact that the element name is misleading. The ReqICMLabel is only for standalone setup. If in a Standalone VXML setup if you would need few piece of dynamic information from ICM, you could use this node. In Comprehensive setup this is not gonna work.
The Standalone with Request ICM Label variation of the Standalone call flow model performs a route request to Unified ICME, and then Unified ICME starts a script (new call). UnifiedICME sees whatever the device puts in the new call message, then Unified ICME chooses a target, such as an agent, and sends a label back to the device. That route request to Unified ICME sends other information, such as ECC variables. Unified ICME can pass other ECC variables back to Unified CVP. Also, you need to configure a VXML Server in the UnifiedCVP Call Server for the call flow model.
For me this sounds like a post-route senario in IP-IVR setup. :-)... However, I cant use queue elements or another run external script element for this senario call routing script.
Subject: RE: About ReqICMLabel
Replied by: Matthew Reiter on 09-11-2010 02:58:00 PM
By the way, I see the ReqICMLabel cann't work under Comprehensive Call Flow , what's difference between Comprehensive and Standalone with Reporting Server?
In a comprehensive call flow, the call originally comes into the call server and uses an ICM routing script, whereas in a standalone call flow, the call originally comes into VXML server. The fact that you are calling your VXML application from an ICM routing script means that you are using comprehensive and thus cannot use ReqICMLabel. If all you want to do is pass data from your VXML application to ICM, you can return the data in your CVP Subdialog Return element as caller input or by storing it in the FromExtVXML array.
Subject: RE: About ReqICMLabel
Replied by: Xu Wei on 11-11-2010 08:34:26 AM
Thank you for your help!
Now I understand the difference between Standalone and Comprehensive Call flow, However I'm not familiar with the ICM configuration. As I know: I should configure the Call Server, in the locate static route set the dail number to voice gateway, I should configure the gateway, add the application and the dial number in it, and also add the lable to voice gateway. I should use CM to set the call number to voice gateway. The question is how I configure it in the ICM, Should I still add dail number, Or still set user.microapp.ToExlVXML[0] to be concatenate("application=IDSBGCallCenter;Callid=",Call.user.media.id) and set Run External Script object to be the IVR script which is configer before this. I don't know it is right or wrong, I need your help. I'm confused that how the Call Server to Connect with ICM when it's use Standalone Call Flow, Is it the same with the configuration of Comprehensive Call flow?
My Engilsh is poor, Can you tell me how to configer the ICM when I use the Standalone Call flow .
Subject: RE: About ReqICMLabel
Replied by: Xu Wei on 11-11-2010 08:48:27 AM
Hi, Manoj.
Yes,Now I understand the difference betwenn Standalon and Comprehensive,but for me, How does the Call Server to connect with ICM, it's cinfused for me. I see the document of Configuration and Administration Guide for Cisco Unified Customer Voice Portal, but it's not clearly explain how to connect with ICM. Is the ICM's Configration same with that when using under Comprehensive? if not what's the difference?
Appreciate!
Subject: RE: About ReqICMLabel
Replied by: Manoj Anantha on 11-11-2010 10:11:02 AM
Hi,
I havnt tried this call flow on my lab yet. However, based on the document that I have read, this is what I understand.
Integration:
CVP-VXML Server <-> CVP Call Server <-> ICM VRU PG.
Even though its a standalone enviroment we have integration with ICM. However, When a Voice gateway starts a VXML service for a call, the VXML service would trigger a VXML application based on the configuration. Now when the application encounters ReqICMLabel. It sends a new call request through the call server and then call server would place request with ICM.
So, if the DN that triggered VXML service is 4567. Then you would need a "dialed Number" created in ICM for 4567 for CallServer routing client and specify a call type. To this call type you need schedule the required routing script. This script can max return a labels and data that might be usefull.
Call flow:
PSTN->VG->VXML gateway service.
On ReqICMLable
VXML gateway --trigger> call server --trigger> ICM
Basically in Standalone setup, the call is sent to VXML gateway. After selfservice, the call would be transfered to another DN. You could get this DN label decision involving ICM.
Note: Queueing, Run external script cannot be used in this call flow.
If you have a comprehensive setup, you shouldnt be using ReqICMlable.