cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
509
Views
0
Helpful
0
Comments
cdnadmin
Community Member
This document was generated from CDN thread

Created by: Terry Sposato on 28-04-2011 06:17:54 AM
Hi,
 
We are testing UCCE with CVP at the moment in a lab environment, I am running through the complex exercise from the CVP Get Started 8.5 PDF. We are using UCCE and CVP 8.5 and I am stuck at the moment, we have a VOIP call being placed which is supposed to trigger an ICM script we created, however, using the script monitoring it fails before it is supposed to run the script. Also analysing packets it is never forwarding the request to the CVP VXML server so i believe something is occuring before this...
 
The only error I see is on the Router PIM and it says the following:
NewCall from VRU referenced an unregistered ECC variable tag: 29

Does anyone know where the best place is to look to solve this error? As far as I can tell all the ECC variables are correct and I followed the sample exercise exactly, although in our lab we have the components split on their own servers, however the connectivity is there so I don't believe this is the problem...
 
Any ideas where I can start looking??
 
Regards,
 
Terry

Subject: RE: Re: New Message from Terry Sposato in Customer Voice Portal (CVP) - CVP
Replied by: Terry Sposato on 28-04-2011 07:51:02 PM
Look on the call server in the C:/Cisco/CVP/error.date.log and you
should see the New Call request that's causing your error.
Perhaps you can copy/paste it. It should give an indication of what it's
looking for.



On 4/28/2011 6:17 AM, Cisco Developer Community Forums wrote:
> NewCall from VRU referenced an unregistered ECC variable tag: 29

--
Janine Graves


Hi Janine,
 
Thanks for the pointer to the specific log file, this is what I was lookin for.
We found that we didn't add the route patterns correctly in CVP, added them in and everything worked.
 
Thanks very much.
 
Terry

Subject: RE: PG Error
Replied by: Gerard O'Rourke on 28-04-2011 08:33:27 AM
Terry,
 
I would start by double checking your ECC variables and make sure you have all configured as per the below document - page 129
http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/customer_voice_portal/cvp8_5/configuration/guide/ConfigAdminGuide_8.5.pdf?bcsi_scan_1FC570F51B3F2EE0=0&bcsi_scan_filename=ConfigAdminGuide_8.5.pdf
 
Specifically I would double check the below
user.microapp.media_server
user.microapp.sys_media_lib
user.microapp.app_media_lib
user.microapp.UseVXMLParams
user.microapp.ToExtVXML
user.microapp.FromExtVXML
 
 Also check the config of the VRU script is as per above document - see page 211 and do a search for "GS,Server,V"
 
Gerard

Subject: Re: New Message from Terry Sposato in Customer Voice Portal (CVP) - CVP - A
Replied by: Janine Graves on 28-04-2011 10:43:08 AM
You haven't provided much information for people to help you.

When you make the VOIP call (are you using a SIP phone) - is it hitting
the gateway? You can run some debug commands on the gateway to ensure
it's matching a dial peer.
Do you hear an error message being played back to you?

Is the call hitting the call server (look in the
C:/Cisco/CVP/logs/error.date.log for indication of the call)?

The error message in the PIM logs about uninitialized ECC vars is
probably something you can ignore - I get that a lot, there are plenty
of ECC vars that DON"T need to be initialized. Does the PIM show 'ACTIVE'?

If you run the RouterCallLogger on ICM, doe you see the call hitting it?

Is the call hitting the ICM script (monitor the script in ICM script
editor)?







On 4/28/2011 6:17 AM, Cisco Developer Community Forums wrote:
> Terry Sposato has created a new message in the forum "CVP - All Versions":
>
> --------------------------------------------------------------
> Hi,
> Â
> We are testing UCCE with CVP at the moment in a lab environment, I am
> running through the complex exercise from the CVP Get Started 8.5 PDF.
> We are using UCCE and CVP 8.5 and I am stuck at the moment, we have a
> VOIP call being placed which is supposed to trigger an ICM script we
> created, however, using the script monitoring it fails before it is
> supposed to run the script. Also analysing packets it is never
> forwarding the request to the CVP VXML server so i believe something
> is occuring before this...
> Â
> The only error I see is on the Router PIM and it says the following:
> NewCall from VRU referenced an unregistered ECC variable tag: 29
>
> Does anyone know where the best place is to look to solve this error?
> As far as I can tell all the ECC variables are correct and I followed
> the sample exercise exactly, although in our lab we have the
> components split on their own servers, however the connectivity is
> there so I don't believe this is the problem...
> Â
> Any ideas where I can start looking??
> Â
> Regards,
> Â
> Terry
> --
> To respond to this post, please click the following link:
>
> <http://developer.cisco.com/web/cvp/forums/-/message_boards/view_message/3794508>
>
> or simply reply to this email.

--
Janine Graves

Subject: Re: New Message from Terry Sposato in Customer Voice Portal (CVP) - CVP - A
Replied by: Janine Graves on 28-04-2011 10:47:08 AM
Look on the call server in the C:/Cisco/CVP/error.date.log and you
should see the New Call request that's causing your error.
Perhaps you can copy/paste it. It should give an indication of what it's
looking for.



On 4/28/2011 6:17 AM, Cisco Developer Community Forums wrote:
> NewCall from VRU referenced an unregistered ECC variable tag: 29

--
Janine Graves
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Quick Links