07-15-2016 01:23 AM - edited 03-12-2019 10:23 AM
Hi
Just thought I would upload the config I have been using for my SIPGATE account with CUBE. It took quite a while to get it working.
I use this in my LAB and it seems to work pretty well, I have done inbound and outbound calling and all seems good. The account I have has no monthly line rental and only a PAYG model.
I have only included the parts I believe to be SIPGATE related
Account number will be (123456790ABC)
Phone number will be (02031231212)
sip
rel1xx disable
header-passing
options-ping 60
midcall-signaling passthru
sip-profiles 101
voice class uri ab200 sip
pattern 123456790ABC@sipgate.co.uk
--SIPGATE IP ADDRESS--
voice class uri 100 sip
host ipv4:217.10.79.23
--8[12].. and 1... is my internal range, this section changes the registration and invites to the SIPGATE format--
voice class sip-profiles 101
request INVITE sip-header From modify "<sip:(8[12]...)@sipgate.co.uk>" "<sip:123456790ABC@sipgate.co.uk>"
request REGISTER sip-header To modify "<sip:02031231212@sipgate.co.uk>" "<sip:123456790ABC@sipgate.co.uk>"
request INVITE sip-header From modify "<sip:(1...)@sipgate.co.uk>" "<sip:123456790ABC@sipgate.co.uk>"
dial-peer voice 101 voip
description INBOUND FROM SIPGATE
translation-profile incoming none
call-block translation-profile incoming call_block
call-block disconnect-cause incoming unassigned-number
preference 2
session protocol sipv2
incoming uri via 100
voice-class codec 1
voice-class sip privacy-policy passthru
voice-class sip profiles 101
dial-peer voice 27 voip
translation-profile outgoing OUTBOUND
destination-pattern 9T
session protocol sipv2
session target dns:sipgate.co.uk
voice-class sip privacy-policy passthru
voice-class sip early-offer forced
voice-class sip profiles 101
codec g711alaw
no vad
--This registers the number and account with SIPGATE, without this the number will not be callable--
sip-ua
credentials username 123456790ABC password 7 HASHOFPASSWORD realm sipgate.co.uk
credentials number 02031231212 username 123456790ABC password 7 HASHOFPASSWORD realm sipgate.co.uk
authentication username 123456790ABC password 7 HASHOFPASSWORD realm sipgate.co.uk
retry invite 2
retry bye 1
timers expires 60000
timers connect 1000
registrar dns:sipgate.co.uk expires 60
Gary
Hi Gary,
Do you know if your inbound Sip-uri invite from sipgate contained your username please? I have problem where my cube needs called number in sip uri but gets username causing inbound calls to fail.
Hope you can advise?
Martin.
Hi
I will need to pull the logs from an active call but if you register the number using the following my CUBE accepted the call.
credentials number 02031231212 username 123456790ABC password 7 HASHOFPASSWORD realm
Gary
Hi Gary,
I have used some of you config and outbound calls are working great. Inbound won't work or match my dial-peers.
I have attached:
1) Config
2) Debug ccsip messages and debug voice ccapi output
3) show sip-au register status - This shows both my creds and number as registered.
NOTE: some of the dial-peers are shutdown as i used them for testing.
Any chance you could take a look please?
Regards,
Martin
Hello Gary,
Would it be possible for you to send me the output of an inbound call trace please.
I have attached my trace and would find it useful to compare the two. For some reason I don't seem to be able to match inbound.
Your help would be greatly appreciated.
Regards,
Martin.
Hi Gary,
Many thanks for the trace. The problem has now been spotted and fixed.
I had no 'trusted devices' in my trust list hence the calling party was not allowed onto the cube. After adding the correct trusted ip address's the trace look very similar to yours and calls are now accepted inbound.
Thanks again for you help,
Martin.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: