cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
557
Views
0
Helpful
0
Comments
cdnadmin
Community Member
This document was generated from CDN thread

Created by: Daniel Placek on 25-09-2011 11:44:30 AM
Having some trouble getting this working on a UC540. It says in an earlier thread that this is supported as long as you have latest firmware.
 
I have 15.1(2)T4
 
My issue is that the instructions for the demo specify:


voice register
session-server  1

  keepalive 60
  register-id OCT_CME
  cti-aware
 
However, "voice register session-server 1" is not a valid command.




UC540(config)#voice register session-server 1
                             ^
% Invalid input detected at '^' marker.

Subject: RE: UC540
Replied by: Daniel Placek on 25-09-2011 12:09:45 PM
Done. Thanks for the fast response.

Subject: RE: UC540
Replied by: Daniel Placek on 25-09-2011 12:18:38 PM
UC540(config)#voice ?
  call                 Voice call related configuration.
  cause-code           Sets the internal Q850 cause code mapping
  class                Control parameters class
  disc-pi-incoming-on  disconn with PI from incoming leg is maintained
  dnis-map             Create or add to a dnis-map
  dsp                  DSP functions
  emergency            Emergency configuration commands
  enum-match-table     enum match table entry
  hpi                  Host port interface
  hunt                 Dialpeer hunt conditions.
  hunt-group           Define VOICE hunt group number
  iec                  Configure Internal Error Code behavior
  logout-profile       extension mobility logout profile
  lpcor                Voice Logical Partitioning COR commands
  mlpp                 Define Voice MLPP Commands
  moh-group            Define voice Music-on-Hold group number
  register             voice register commands
  rtp                  enable to open RTP in both directions.
  service              Global packet telephony service commands
  source-group         Source Group configuration commands
  statistics           Voice Statistics
  translation-profile  Translation profile configuration commands
  translation-rule     Translation Rule configuration commands
  user-profile         extension mobility user profile
  vad-time             Voice activity detection hangover period
  vrf                  Voice VRF

Subject: RE: UC540
Replied by: Daniel Placek on 25-09-2011 12:20:28 PM
wow. Apparently I am slow today. Somehow "voice register session-server" exists now. I must have mis-pasted or something. Really sorry for wasting your time. 😕

Subject: RE: UC540
Replied by: Daniel Placek on 25-09-2011 12:24:47 PM
Well. The example app seems to work now... sortof. Its connecting successfully, and seems to receive events.

However, when trying to "place a call, then put on hold",

>>>>>Sample code: =============== Provider in service now ===============


>>>>>Sample code: ++++++ Provider is in service, now adding phones ++++++

>>>>>Sample code: +++++++++++++++++++++ phone1 added +++++++++++++++++++++
>>>>>Sample code: +++++++++++++++++++++ phone2 added +++++++++++++++++++++
>>>>>Sample code: ########## CMENotification.Type.ADDRESS_ACTIVATED ##########
>>>>>Sample code: ########## CMEAddressActivatedEvent received :301 ##########
>>>>>Sample code: ########## CMENotification.Type.ADDRESS_ACTIVATED ##########
>>>>>Sample code: ########## CMEAddressActivatedEvent received :302 ##########
>>>>>Sample code: +++++++++++++++++++++ now making call +++++++++++++++++++++

However, nothing happens on either phone. If I take them offhook, I see the events though.

Any thoughts?
 
EDIT:
Are there any debug's related to UCXSI?

Subject: RE: UC540
Replied by: Daniel Placek on 25-09-2011 12:37:49 PM
Well, it seems that the problem isn't UCXSI, but the phone itself. I am using a SPA508G and a CIPC to test this, the CIPC works fine, but the SPA508G is doing weird stuff. However, after playing with it for a bit, it doesn't seem the problem is related to UCXSI... it looks like either its just older firmware issues, or a bad phone.

Subject: RE: UC540
Replied by: Luke Krouse on 25-09-2011 12:06:00 PM
Having some trouble getting this working on a UC540. It says in an earlier thread that this is supported as long as you have latest firmware.
 
I have 15.1(2)T4
 
My issue is that the instructions for the demo specify:


voice register
session-server  1

  keepalive 60
  register-id OCT_CME
  cti-aware
 
However, "voice register session-server 1" is not a valid command.




UC540(config)#voice register session-server 1
                             ^
% Invalid input detected at '^' marker.

 
 

Daniel,
 
Can you please attach your running config?

Subject: RE: UC540
Replied by: Luke Krouse on 25-09-2011 12:17:42 PM
Can you please type the following in the config: voice ? I would like to see what options you have.

KROUSE(config)#voice ?
  call                 Voice call related configuration.
  cause-code           Sets the internal Q850 cause code mapping
  class                Control parameters class
  disc-pi-incoming-on  disconn with PI from incoming leg is maintained
  dnis-map             Create or add to a dnis-map
  dsp                  DSP functions
  emergency            Emergency configuration commands
  enum-match-table     enum match table entry
  hpi                  Host port interface
  hunt                 Dialpeer hunt conditions.
  hunt-group           Define VOICE hunt group number
  iec                  Configure Internal Error Code behavior
  logout-profile       extension mobility logout profile
  lpcor                Voice Logical Partitioning COR commands
  mlpp                 Define Voice MLPP Commands
  moh-group            Define voice Music-on-Hold group number
  register             voice register commands
  rtp                  enable to open RTP in both directions.
  service              Global packet telephony service commands
  source-group         Source Group configuration commands
  statistics           Voice Statistics
  translation-profile  Translation profile configuration commands
  translation-rule     Translation Rule configuration commands
  user-profile         extension mobility user profile
  vad-time             Voice activity detection hangover period
  vrf                  Voice VRF

Subject: RE: UC540
Replied by: Luke Krouse on 25-09-2011 12:21:19 PM
No worries.

Subject: RE: UC540
Replied by: Luke Krouse on 25-09-2011 12:57:10 PM
Well, it seems that the problem isn't UCXSI, but the phone itself. I am using a SPA508G and a CIPC to test this, the CIPC works fine, but the SPA508G is doing weird stuff. However, after playing with it for a bit, it doesn't seem the problem is related to UCXSI... it looks like either its just older firmware issues, or a bad phone.

 
Daniel,
 
The SPA series phones do require an updated firmware to work. I am not sure what version it is but it allows the SPA500 series to act more like the 7900 series. It also allows them to display GET requests.
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Quick Links