More and more companies these days have mobile workforces: teams that work on the road or who have the ability to work from home. To help maximize efficiency and to make this mobility seamless to the individuals and the rest of the team Mobile and Remote Access (MRA) via Cisco Expressway is the key. Being able to use Cisco Jabber and IM&P help bring mobile collaboration to another level. However, there are times when this seamless mobility runs into a snag and an error occurs; one of the most common errors while using Jabber in MRA mode via Cisco Expressway is "cannot communicate with the server". Today's tip is about how to effectively troubleshoot this problem.
Cisco Jabber login error when trying to communicate using Mobile and Remote Access via Cisco Expressway: "cannot communicate with the server".''
The following will outline three areas to explore when troubleshooting your Cisco Jabber login error: " cannot communicate with server" when trying to communicate using Mobile and Remote Access via Cisco Expressway. In this scenario, we will assume that the user is able to login to Jabber from inside the corporate LAN and focus our troubleshooting efforts on Expressway pair servers.
STEP 1. Verify the DNS and firewall related configurations.
Verify that the collab-edge.tls.company.com SRV type DNS record is present. Please note that it is important to set the type to SRV. In this example below, we use a well known public DNS server.
b) Verify that the returned FQDN of the Expressway-Edge server from the SRV record is resolving to an IP address.
c) Verify that the Cisco Expressway-Edge server's FQDN name matches exactly the value created in the collab-edge SRV record.
d) Verify that the corporate firewall has a rule for port 8443 that forwards traffic to the DMZ LAN interface of the Expressway-Edge server.
STEP2. Verify that the traversal-zone between Cisco Expressway Edge and Core servers are <<Active>>.
Verify the Expressway-Edge server.
b) Verify the Cisco Expressway-Core server.
c) Verify that Unified Communications status on Cisco Expressway-Core is enabled and configured
If both the main configuration and the Cisco Expressway-Edge and Core servers are active then proceed to step 3 and start digging into the log files.
STEP 3. Dig into the log files of Expressway.
Start by digging into the Network logs and filter using <<trafficserver>>. This will help you see how the get_edge_config process between the Edge and Core servers is happening.
b) Now begin a dignostic log and reproduce your problem. Make sure to check <<take tcpdump while logging>> which will generate a pcap file as well. Note: there is an alarm active once you start your diagnostic log and it will disappear automatically when you stop the diagnostics. There is also a <<download>> option available after diagnostic logging is complete. These logs are the first thing that the Cisco TAC will require from you if you open a case with Cisco in regards to Expressway.
Analyze the logs. The following identify the two most common errors to look for in your diagnostic logs.
Error: <<SIP/2.0 405 Method Not Allowed>> If this error is found in the Core logs, it is in response to SIP registration request failure.
Resolution: The error is usually due to an existing SIP trunk between Expressway-C and CUCM using port 5060/5061 (the trunk is not used for MRA, but usually is created for another feature of Expressway – B2B dialing). In order to correct the issue, you will have to change the SIP port on the SIP Trunk Security Profile that is applied to the existing SIP trunk configured in CUCM. You can use 5065 instead.
Error: <<edgeconfigprovisioning: Level="WARNING" Service="UDSManager" Detail="User cluster not found">> If this error is found and you have multiple Unifed CM clusters defined in Expressway-Core.
Resolution:In this case ILS (Intercluster Lookup Service) must be set up on all of the clusters. This is because the Expressway has to authenticate a client against its home Unified CM cluster and to discover the home cluster it sends a UDS (User Data Service) query to any one of the Unified CM nodes over ILS.
In our tenant we have 30 days setup as our retention policy, today we noticed a moderated space (that has not been used in the last 30 days) was missing. I thought the 30 day retention was only for the content of spaces/direct messages NOT the actual spac...
We're developing a PowerBI dashboard for reporting UCCX stats and I've provided ODBC access to db_cra to our PowerBI team. They want to have the Informix OLE DB provider, but it requires running a script called coledbp.sql against sysmaster using th...
I have a call script with a menu within asking the end user to opt out if they want to leave a message. i have the script handled the call:in the menu for 1 for voicemail set contact info ( triggered contact- handled)set ext = to ext go to...
Hello there!I'm struggling with a normalization script to modify an incoming (from Avaya) INVITE to replace the incorrect IP address they are sending with the proper IP address. I have it working with the To: field, but not the INVITE field.This works to ...
Hi as i know during the installation of CVP call/VXML we must select what codec can be used for the example below. so the question is how to if we need to change for example in the installation I used g711alaw and the after installation fi...