invalid power sense cisco 2960-X

[Jesus Flores Tello]

Estimados, Podrian ayudarme a identificar este problema que me esta mostrando en el log de mi switch. envio los datos del equipo y logs:

Modelo

WS-C2960X-24PS-L

Version

15.0(2a)EX5  

Imagen

 C2960X-UNIVERSALK9-M 

Logs aparecidos en el switch:

.Jun 22 12:41:56: %ILPOWER-5-SENSE_POWER_INVALID: Interface Gi1/0/1: invalid power sense 51484 milliwatts current 999 mA voltage 51536 mV

Las pruebas

SWSFAQP34C#show power inline

Module Available Used Remaining
(Watts) (Watts) (Watts)
------ --------- -------- ---------
1 370.0 245.0 125.0
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Gi1/0/1 auto off 0.0 n/a n/a 30.0
Gi1/0/2 auto on 7.0 Ieee PD 2 30.0
Gi1/0/3 auto off 0.0 n/a n/a 30.0
Gi1/0/4 auto on 15.4 Ieee PD 3 30.0
Gi1/0/5 auto off 0.0 n/a n/a 30.0
Gi1/0/6 auto on 15.4 Ieee PD 3 30.0
Gi1/0/7 auto on 15.4 Ieee PD 3 30.0
Gi1/0/8 auto on 15.4 Ieee PD 3 30.0
Gi1/0/9 auto on 15.4 Ieee PD 3 30.0
Gi1/0/10 auto on 15.4 Ieee PD 4 30.0
Gi1/0/11 auto off 0.0 n/a n/a 30.0
Gi1/0/12 auto on 15.4 Ieee PD 3 30.0
Gi1/0/13 auto on 15.4 Ieee PD 3 30.0
Gi1/0/14 auto on 15.4 Ieee PD 3 30.0
Gi1/0/15 auto on 15.4 Ieee PD 3 30.0
Gi1/0/16 auto on 15.4 Ieee PD 3 30.0
Gi1/0/17 auto on 15.4 Ieee PD 3 30.0
Gi1/0/18 auto on 15.4 Ieee PD 3 30.0
Gi1/0/19 auto on 15.4 Ieee PD 3 30.0
Gi1/0/20 auto off 0.0 n/a n/a 30.0
Gi1/0/21 auto on 15.4 Ieee PD 3 30.0
Gi1/0/22 auto off 0.0 n/a n/a 30.0
Gi1/0/23 auto on 7.0 Ieee PD 2 30.0
Gi1/0/24 auto off 0.0 n/a n/a 30.0
SWSFAQP34C#

el problema es que la camara poe que va conectado al puerto 1/0/1 se esta apagando y prendiendo automaticamente cada 2 minutos.  

Favor, espero me puedan ayudar a indentificar el problema. Si necesitan algun dato me avisan.

Gracias

Saludos

Jesus Flores.

[Diana Karolina Rojas · Accepted solution]

Hola por favor enviar los siguientes comandos:

show int Gi1/0/1

show power inline Gi1/0/1 det

si tienes cdp o lldp habilitado en la interfaz te voy a pedir que lo deshabilites, levantes y subas la interfaz.

como última alternativa también te voy a pedir que cambies el cable que conecta a la camara al switch.

Por favor no olvides calificar las respuestas útiles.

Saludos,

[Jesus Flores Tello]

Hola Diana, Te agrezco tu ayuda: Te comento que he cambiado de puerto del switch del 1/0/1 hacia el 1/0/7

------------------------------------------
SWSFAQP34C#show int gig 1/0/7
GigabitEthernet1/0/7 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 0057.d2b0.8207 (bia 0057.d2b0.8207)
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 212000 bits/sec, 27 packets/sec
5 minute output rate 18000 bits/sec, 28 packets/sec
615615 packets input, 442804690 bytes, 0 no buffer
Received 2883 broadcasts (2419 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 2419 multicast, 0 pause input
0 input packets with dribble condition detected
515792 packets output, 64404854 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
SWSFAQP34C#


SWSFAQP34C#show power inline gigabitEthernet 1/0/7 det
Interface: Gi1/0/7
Inline Power Mode: static
Operational status: on
Device Detected: no
Device Type: Ieee PD
IEEE Class: 3
Discovery mechanism used/configured: Unknown
Police: off

Power Allocated
Admin Value: 30.0
Power drawn from the source: 30.0
Power available to the device: 30.0

Actual consumption
Measured at the port: 2.9
Maximum Power drawn by the device since powered on: 3.3

Absent Counter: 0
Over Current Counter: 0
Short Current Counter: 0
Invalid Signature Counter: 0
Power Denied Counter: 0

Power Negotiation Used: None
LLDP Power Negotiation --Sent to PD-- --Rcvd from PD--
Power Type: - -
Power Source: - -
Power Priority: - -
Requested Power(W): - -
Allocated Power(W): - -
SWSFAQP34C#
---------------------------------------
SWSFAQP34C#show run int gig 1/0/7
Building configuration...

Current configuration : 390 bytes
!
interface GigabitEthernet1/0/7
switchport access vlan 509
switchport mode access
switchport nonegotiate
switchport port-security maximum 2
switchport port-security
switchport port-security aging time 2
switchport port-security violation restrict
switchport port-security aging type inactivity
power inline static
speed 100
no snmp trap link-status
spanning-tree portfast
end

SWSFAQP34C#
-------------------------
SWSFAQP34C#show powe
System Power Total (AC) 653 Watts
System Power Used (AC) 429 Watts

SWSFAQP34C#

------------------
SWSFAQP34C#show power inline consumption
Interface Consumption Admin
Configured Consumption (Watts)
---------- ----------- -------------------

Gi1/0/1 NO 0.0
Gi1/0/2 NO 0.0
Gi1/0/3 NO 0.0
Gi1/0/4 NO 0.0
Gi1/0/5 NO 0.0
Gi1/0/6 NO 0.0
Gi1/0/7 NO 0.0
Gi1/0/8 NO 0.0
Gi1/0/9 NO 0.0
Gi1/0/10 NO 0.0
Gi1/0/11 NO 0.0
Gi1/0/12 NO 0.0
Gi1/0/13 NO 0.0
Gi1/0/14 NO 0.0
Gi1/0/15 NO 0.0
Gi1/0/16 NO 0.0
Gi1/0/17 NO 0.0
Gi1/0/18 NO 0.0
Gi1/0/19 NO 0.0
Gi1/0/20 NO 0.0
Gi1/0/21 NO 0.0
Gi1/0/22 NO 0.0
Gi1/0/23 NO 0.0
Gi1/0/24 NO 0.0
--------------------------------
SWSFAQP34C#show power inline

Module Available Used Remaining
(Watts) (Watts) (Watts)
------ --------- -------- ---------
1 370.0 349.4 20.6
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Gi1/0/1 static off 30.0 n/a n/a 30.0
Gi1/0/2 static on 30.0 Ieee PD 2 30.0
Gi1/0/3 auto off 0.0 n/a n/a 30.0
Gi1/0/4 static on 30.0 Ieee PD 3 30.0
Gi1/0/5 auto off 0.0 n/a n/a 30.0
Gi1/0/6 static off 30.0 n/a n/a 30.0
Gi1/0/7 static on 30.0 Ieee PD 3 30.0
Gi1/0/8 auto off 0.0 n/a n/a 30.0
Gi1/0/9 auto on 15.4 Ieee PD 3 30.0
Gi1/0/10 auto on 15.4 Ieee PD 4 30.0
Gi1/0/11 auto off 0.0 n/a n/a 30.0
Gi1/0/12 auto on 15.4 Ieee PD 3 30.0
Gi1/0/13 auto on 15.4 Ieee PD 3 30.0
Gi1/0/14 auto on 15.4 Ieee PD 3 30.0
Gi1/0/15 auto on 15.4 Ieee PD 3 30.0
Gi1/0/16 auto on 15.4 Ieee PD 3 30.0
Gi1/0/17 auto on 15.4 Ieee PD 3 30.0
Gi1/0/18 auto on 15.4 Ieee PD 3 30.0
Gi1/0/19 auto on 15.4 Ieee PD 3 30.0
Gi1/0/20 auto off 0.0 n/a n/a 30.0
Gi1/0/21 auto on 15.4 Ieee PD 3 30.0
Gi1/0/22 auto off 0.0 n/a n/a 30.0
Gi1/0/23 static on 30.0 Ieee PD 2 30.0
Gi1/0/24 auto off 0.0 n/a n/a 30.0

---------------------------------------------------------------
SWSFAQP34C#show int status

Port Name Status Vlan Duplex Speed Type
Gi1/0/1 notconnect 509 auto auto 10/100/1000BaseTX
Gi1/0/2 connected 509 a-full a-100 10/100/1000BaseTX
Gi1/0/3 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/4 connected 509 a-full a-100 10/100/1000BaseTX
Gi1/0/5 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/6 CAMARA ANTIGUIO notconnect 509 auto 100 10/100/1000BaseTX
Gi1/0/7 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/8 CAMARA ANTIGUIO notconnect 509 auto 100 10/100/1000BaseTX
Gi1/0/9 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/10 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/11 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/12 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/13 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/14 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/15 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/16 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/17 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/18 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/19 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/20 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/21 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/22 connected 509 a-full 100 10/100/1000BaseTX
Gi1/0/23 connected 509 a-full a-100 10/100/1000BaseTX
Gi1/0/24 Up_SWSFAQP35C connected trunk a-full a-1000 10/100/1000BaseTX
Gi1/0/25 notconnect 1 auto auto Not Present
Gi1/0/26 notconnect 1 auto auto Not Present
Gi1/0/27 UP_SWSFAQP11_1 connected trunk a-full a-1000 1000BaseSX SFP
Gi1/0/28 notconnect 1 auto auto Not Present
Fa0 notconnect routed auto auto 10/100BaseTX
-------------------------------------------------------------------

CDP DESHABILITADO EN TODAS LAS INTEFFACES
---------------------------------------------------------------------

.Jun 22 15:44:56: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/7: PD removed
.Jun 22 15:44:57: %ILPOWER-7-DETECT: Interface Gi1/0/7: Power Device detected: IEEE PD
.Jun 22 15:44:57: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/7, changed state to down
.Jun 22 15:44:58: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/7: Power granted
.Jun 22 15:44:58: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/7, changed state to down
.Jun 22 15:45:03: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/7, changed state to up
.Jun 22 15:45:04: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/7, changed state to up
.Jun 22 15:45:06: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/7, changed state to down
.Jun 22 15:45:06: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/2: PD removed
.Jun 22 15:45:07: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/7, changed state to down
.Jun 22 15:45:07: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/2, changed state to down
.Jun 22 15:45:08: %ILPOWER-7-DETECT: Interface Gi1/0/2: Power Device detected: IEEE PD
.Jun 22 15:45:08: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to down
.Jun 22 15:45:08: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/2: Power granted
.Jun 22 15:45:10: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/7, changed state to up
.Jun 22 15:45:11: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/7, changed state to up
.Jun 22 15:45:14: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/7, changed state to down
.Jun 22 15:45:16: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to up
.Jun 22 15:45:16: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/7, changed state to up
.Jun 22 15:45:18: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to down
.Jun 22 15:45:22: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to up
.Jun 22 15:45:23: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/2, changed state to up
.Jun 22 15:45:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/2, changed state to down
.Jun 22 15:45:27: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/2, changed state to up
.Jun 22 15:46:35: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/7: PD removed
.Jun 22 15:46:35: %ILPOWER-7-DETECT: Interface Gi1/0/7: Power Device detected: IEEE PD
.Jun 22 15:46:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/7, changed state to down
.Jun 22 15:46:37: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/7, changed state to down
.Jun 22 15:46:37: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/7: Power granted
.Jun 22 15:46:42: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/7, changed state to up
.Jun 22 15:46:43: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/7, changed state to up
.Jun 22 15:46:45: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/7, changed state to down
.Jun 22 15:46:46: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/7, changed state to down
.Jun 22 15:46:49: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/7, changed state to up
.Jun 22 15:46:50: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/7, changed state to up
.Jun 22 15:46:54: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/7, changed state to down
.Jun 22 15:46:56: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/7, changed state to up
.Jun 22 15:52:18: %ILPOWER-5-SENSE_POWER_INVALID: Interface Gi1/0/7: invalid power sense 51180 milliwatts current 999 mA voltage 51232 mV
SWSFAQP34C#
--------------------------------------------------------------------------
* Me Falta cambiar de cable, que lo he solicitado y en breve me confirman.

[Diana Karolina Rojas]

Por otro lado... según la documentación de la cámara ¿cuanto consume? te recuerdo que tu modelo tiene la siguiente capacidad, y no tiene para brindar UPOE (60W).

Cisco Catalyst 2960X-24PS-L

12 ports up to 30W

24 ports up to 15.4W

370W

Por favor no olvides calificar las respuestas útiles.

Saludos,

[Jesus Flores Tello]

Hola Diana, Las especificaciones de las camaras.
https://www.young.hu/docs/2016KDOK000184001.pdf
https://www.hikvision.com/upload/20170115005557950.pdf

Saludos
Jesus Flores.

[Diana Karolina Rojas]

Estimado por lo que pude revisar este es el detalle de tu log:

The power-monitoring voltage or current value is invalid. [chars] is the interface. The first [dec] is the power-monitoring cutoff value, the second [dec] is the real-time power consumption in mA, and the third [dec] is the real-time power consumption in mV.

Tomando en cuenta esto tus logs estan mostrando que la cama tiene un cutoff de 51,18 Watts, lo que se excede de los valores que puede proveer este switch, puede que se trate de algo netamente de este switch o es un problema de la cámara (porque por la información que me enviaste no llega a consumir mas de 24 W, ¿intentaste conectarla con otro cable finalmente? ¿intentaste conectarla a otro switch POE? ¿puedes colocar el puerto como default y conectarla así?

Por favor no olvides calificar las respuestas útiles.

Saludos,

[Jesus Flores Tello]

 Hola Diana, Mira he realizado los siguiente: 

• Se apagó y prendió el puerto.
• Se reinició el switch.
• Se mandó por default el puerto.
• Se deshabilito el cdp y lldp en la interfaz y de manera global.
• Se identificó que no hay errores físicos ni lógicos en el puerto.
• Se cambió de cable.
• Se trasladó la cámara hacia otro switch y funcionó automáticamente no mostrando los logs enviados del switch reportado.
• Se intercambió el puerto de la cámara reportada en el mismo switch a un puerto de una cámara que no tenía problemas y  la cámara reportada dejó de presentar la intermitencia, pero la otra cámara que si funcionaba  volvió con los síntomas de intermitencia (descartando problema de la camara)
• Gi1/0/10  auto   on         15.4    Ieee PD             3     30.0  (camara cambiada a otro puerto se ve que negocia y no presenta los errores mencionados)

Segun los datasheets el modelo no deberia de sobrepasar los 18W.

Puerto 7: Modelo 2720

https://www.hikvision.com/upload/20170115005557950.pdf

Puerto 10: Modelo 5220

https://www.young.hu/docs/2016KDOK000184001.pdf

ya no sé que mas realizar. Aparentemente es un tema del puerto por los ultimos descartes mencionados.

Muchas gracias.

Jesus 

[Diana Karolina Rojas]

Si el mismo puerto te falló con cámaras distintas entonces mi recomendación es que abras un caso en el TAC por falla de hardware.

Saludos,

[miguel_montiel]

Hola buenas tardes,

a mi me esta presentando la misma falla que al compañero Jesús, abajo les adjunto los logs y si me pueden indicar si levanto un TAC o RMA por daño en puertos del Switch???

000071: Sep 10 15:21:40.427 CST: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/5: PD removed
000072: Sep 10 15:21:40.885 CST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/5, changed state to down
000073: Sep 10 15:21:41.892 CST: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/5, changed state to down
000074: Sep 10 15:21:42.165 CST: %SWITCH_QOS_TB-5-TRUST_DEVICE_LOST: cisco-phone no longer detected on port Gi1/0/5, operational port trust state is now untrusted.
000075: Sep 12 13:52:15.807 CST: %SYS-5-CONFIG_I: Configured from console by miguelm on vty0
000076: Sep 14 10:44:40.581 CST: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/4: PD removed
000077: Sep 14 10:44:41.066 CST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/4, changed state to down
000078: Sep 14 10:44:42.066 CST: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/4, changed state to down
000079: Sep 14 10:44:42.251 CST: %SWITCH_QOS_TB-5-TRUST_DEVICE_LOST: cisco-phone no longer detected on port Gi1/0/4, operational port trust state is now untrusted.
000080: Sep 23 09:19:10.279 CST: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/3: PD removed
000081: Sep 23 09:19:10.670 CST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/3, changed state to down
000082: Sep 23 09:19:11.673 CST: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/3, changed state to down
000083: Sep 23 09:19:14.539 CST: %SWITCH_QOS_TB-5-TRUST_DEVICE_LOST: cisco-phone no longer detected on port Gi1/0/3, operational port trust state is now untrusted.
000084: Sep 27 10:58:02.951 CST: %ILPOWER-7-DETECT: Interface Gi1/0/5: Power Device detected: IEEE PD
000085: Sep 27 10:58:04.129 CST: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/5: Power granted
000086: Sep 27 10:58:07.582 CST: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/5, changed state to up
000087: Sep 27 10:58:08.586 CST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/5, changed state to up
000088: Sep 27 10:58:19.620 CST: %SWITCH_QOS_TB-5-TRUST_DEVICE_DETECTED: cisco-phone detected on port Gi1/0/5, port's configured trust state is now operational.
000089: Oct 8 14:47:18.464 CST: %ILPOWER-7-DETECT: Interface Gi1/0/4: Power Device detected: IEEE PD
000090: Oct 8 14:47:19.191 CST: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/4: Power granted
000091: Oct 8 14:47:22.602 CST: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/4, changed state to up
000092: Oct 8 14:47:23.605 CST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/4, changed state to up
000093: Oct 8 14:47:34.724 CST: %SWITCH_QOS_TB-5-TRUST_DEVICE_DETECTED: cisco-phone detected on port Gi1/0/4, port's configured trust state is now operational.
000094: Oct 22 14:11:07.459 CST: %ILPOWER-7-DETECT: Interface Gi1/0/3: Power Device detected: IEEE PD
000095: Oct 22 14:11:08.144 CST: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/3: Power granted
000096: Oct 22 14:11:11.577 CST: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/3, changed state to up
000097: Oct 22 14:11:12.580 CST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/3, changed state to up
000098: Oct 22 14:11:15.883 CST: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/3: PD removed
000099: Oct 22 14:11:16.390 CST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/3, changed state to down
000100: Oct 22 14:11:17.393 CST: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/3, changed state to down