cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
494
Views
0
Helpful
4
Replies

cisco VG to PBX problem

miskoolak
Level 1
Level 1

Hi

I have coonectd my router via a wvic (E1 Qsig) to a pbx.

the pbx users can call my fxs ports and they can talk,but the problem is when I try to call them from FXS analoge telefone tp PBX users.. their phone will ring but I can not hear anythig and also when they pick up the phone no timeslot will be activated and therefore i can not here their voice.

please help me

4 Replies 4

subhrojyoti_hp
Level 1
Level 1

Could you post the following-

1. sh run

2. deb isdn q931 / deb voice ccapi in out

Subhrojyoti

BX-VG#

*Oct 16 11:00:49.147: ISDN Se0/0/0:15 Q931: Applying typeplan for sw-type 0x16 is 0x0 0x0, Calling num 8

*Oct 16 11:00:49.147: ISDN Se0/0/0:15 Q931: Applying typeplan for sw-type 0x16 is 0x0 0x0, Called num 2830

*Oct 16 11:00:49.151: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x008E

Sending Complete

Bearer Capability i = 0x9090A3

Standard = CCITT

Transfer Capability = 3.1kHz Audio

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA9838A

Exclusive, Channel 10

Progress Ind i = 0x8183 - Origination address is non-ISDN

Calling Party Number i = 0x0080, '8'

Plan:Unknown, Type:Unknown

Called Party Number i = 0x80, '2830'

Plan:Unknown, Type:Unknown

*Oct 16 11:00:49.243: ISDN Se0/0/0:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0x808E

*Oct 16 11:00:49.247: ISDN Se0/0/0:15 Q931: TX -> STATUS pd = 8 callref = 0x008E

Cause i = 0x80E018 - Mandatory information element missing

Call State i = 0x01

*Oct 16 11:00:49.271: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x808E

*Oct 16 11:00:49.275: ISDN Se0/0/0:15 Q931: TX -> STATUS pd = 8 callref = 0x008E

Cause i = 0x80E018 - Mandatory information element missing

Call State i = 0x01

*Oct 16 11:00:49.283: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x808E

*Oct 16 11:00:49.287: ISDN Se0/0/0:15 Q931: TX -> STATUS pd = 8 callref = 0x008E

Cause i = 0x80E018 - Mandatory information element missing

Call State i = 0x01

*Oct 16 11:01:05.367: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x008E

Cause i = 0x8090 - Normal call clearing

*Oct 16 11:01:05.439: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x80

Can you try this?

voice call send-alert > under global config

progress_ind alert enable 8 > under the voice dial-peer # pots configuration

Subhrojyoti

hi

i have provided them before but nothing happend

the problem remains! :(

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: