08-05-2008 04:08 AM - edited 03-15-2019 12:24 PM
Any Idea how to configure pri voice service, I try some configurations but does not work.
And idea on how inbound and outbound dial peers should be configured, Im integrating this with CCM 6.x
interface Serial0/1/0:15
no ip address
isdn switch-type primary-net5
isdn incoming-voice modem 64
isdn bchan-number-order ascending
no cdp enable
voice-port 0/1/0:15
dial-peer voice 1 pots
destination-pattern 9T
direct-inward-dial
port 0/1/0:15
08-05-2008 05:58 AM
lets say ur CCM ip 192.168.1.1
and ur extentions between 1000 to 1999
so for calls to CCM voip dial-peer
dial-peer voice 2 voip
destination-pattren 1...
session target:ipv4 192.169.1.1
for calls going to pstn
dial-peer voice 3 pots
destination-patren 9T
port 0/1/0:15
in this case ur useres should dial 9 then the pstn number and dont dicard the 9 on CCM this based on my above dialepeer 3
or u can dicard the ( in the CCM)
do it like
dial-peer voice 3 pots
destination-patren .T
port 0/1/0:15
forwar-digit all
if u want more info just post it here
please, if helpful rate
08-05-2008 08:05 PM
ok, my dial-peer are just like that, but so if this is good in configuration the mistake is in the PRI configuracion, do you know how to configure PRI services?
08-05-2008 08:33 PM
the fowlling things should be don regarding ur hardware moduls
so if u use wic or vwic or if its onboard or in solt one will deffer
router# clear interface s0/0/0:15
!
network-clock-participate wic 0
!
isdn switch-type primary-net5
!
interface Serial0/0/0:15
isdn switch-type primary-net5
isdn overlap-receiving
isdn incoming-voice voice
controller T1 1/0
framing esf
clock source internal
linecode b8zs
cablelength short 133
pri-group timeslots 1-24
where the :
pri-group timeslots timeslot-range [nfas_d {backup | none
| primary {nfas_int number |
nfas_group number | rlm-group number}} | service]
the follwoing link will be very helful for u
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a0080094636.shtml
and this link to have a knowledge about hardware config
http://www.cisco.com/en/US/docs/ios/12_2t/12_2t15/feature/guide/ftbckaim.html
good luck
Please, if Hlepful Rate
08-06-2008 07:13 AM
08-06-2008 07:25 AM
first of all
u need to check how many digits u r forwarding
and how many digit u recieve from the gatway
u made the pots dial peer as DID
that mean the whole number will be recieved from the pstn
so is range of pstn number will be wthin
destination-pattern 605.. this one
if not
u have to either forward the full number to the CCM
and in the gateway page in CCM chose the number of digits u wanna use for internal phon
in the significant digits option
or make a translation profile on the gateway that send only 4 digits to ur CCM
so just check ur numbering paln and config
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide