Dear all,
I've MGX 8850 [ with PXM-1E (with 8 E3) and RPM-PR (NPE400) processor ] .....It's acting as an ATM edge-LSR in our cell-mode MPLS network
(This network is based on MGX 8850 with RPM-PR acting as ATM edge-LSRs and the BPX 8600 with LSC 7200 acting as the ATM LSR)
The problem is that I'm facing difficulties in adding connections between the PXM-1E (slave) and RPM-PR (Master).
1- RPM-PR IOS ver is 12.2(11)T2
2- PXM ver is 3.0(20.0)
3- The steps I follow for PXM-1E config are
a- upln 2.1
b- cnfln -e3 2.1 -len 30 -clk 2
c- addport 1 2.1 80000 80000 0 1
80000 ----->guaranteeRate in cells/sec
80000------> maxRate in cells/sec
0------------> sctId -- SCT file ID between 0 and 255, for default file use 0
1------------> ifType -- 1: uni 2: nni 3: vnni 4: vuni 5: evuni 6: evnni
d- TOTO.7.PXM.a > dsplns
Line Line Line Line Length OOF AIS Valid Alarm
Num State Type Lpbk (meters) Criteria cBitsCheck Intvls State
----- ----- ----------- ---------- ------- -------- ---------- ------ -------
2.1 Up e3g832adm NoLoop 0 N/A N/A 96 Clear
e- TOTO.7.PXM.a > dspports
ifNum Line Admin Operational Guaranteed Maximum sctID ifType VPI MI
NVPI MAXVPI IMA
State State Rate Rate Conf./InUse (VNNI, (E
VUNI, (EVUNI, GRP
VUNI) E
VNNI) EVNNI)
----- ---- ----- -------------- ---------- ------- ------------ ------ ------ --
----- ------- ---
1 2.1 Up Up 80000 80000 0/ 0 =Def UNI 0
f- addpart 1 4 4 100 100 100 100 0 255 1 65535 1000 2000
1-----> If Number -- number between 1 and 31
4-----> Partition Number -- Partition Identifier between 1 and 20
4-----> Controller Number -- Controller Identifier between 1 and 254
cntrlrIds 2 and 3 are reserved for PNNI and LSC respect
100----> Egr guaranteed % Bandwidth -- units:0.0001% of interface bandwidth
100----> Egr max % Bandwidth -- units:0.0001% of interface bandwidth
100-----> Ing guaranteed % Bandwidth -- units:0.0001% of interface bandwidth
100-----> Ing max % Bandwidth -- units:0.0001% of interface bandwidth
0--------> Minimum VPI Value -- number between 0 and 4095(0..255 for UNI interface
255----> Maximum VPI Value -- number between 0 and 4095(0..255 for UNI interfac
1-------> Minimum VCI Value -- number between 1 and 65535
65535-----> Maximum VCI Value -- number between 1 and 65535
1000----> Guaranteed number of conns -- number between 0 and 27000
between 10 and 13500 for PXM1E-16-T1E1
2000---->Max. number of conns -- number between 10 and 27000
between 10 and 13500 for PXM1E-16-T1E1
g- TOTO.7.PXM.a > dspparts
if part Ctlr egr egr ingr ingr min max min max min max
Num ID ID GuarBw MaxBw GuarBw MaxBw vpi vpi vci vci conn conn
(.0001%)(.0001%)(.0001%)(.0001%)
-----------------------------------------------------------------------------
1 4 4 100 100 100 100 0 255 1 65535 1000 2000
h-TOTO.7.PXM.a > addcon
Err: Mandatory argument required.
Syntax: addcon ifNum vpi vci serviceType mastership
g- addcon 1 4 0 1 2
1-----> ifNum -- interface number (1..31)
4 ----> vpi -- vpi (UNI: 0..255 | NNI: 0..4095)
0------> vci -- vci: VCC (1..65535); VPC (0)
1------> serviceType -- cbr1(1) | vbr1rt(2) | vbr2rt(3) |
vbr3rt(4) | vbr1nrt(5) | vbr2nrt(6) |
vbr3nrt(7) | ubr1(8) | ubr2(9) |
2-----> mastership -- m (1) | s (2)
ERR: Error sending pass up message
I'd like to know what and why this error appear to me while i'm adding the connection ....wht's wrong??
Plz can anyone advise??
Regards,
Komy
