cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
290
Views
0
Helpful
1
Replies

VPLS Problem on NCS540

 

Hello, we are experiencing an issue with the Cisco NCS540 regarding Layer 2 Virtual Private Network (L2VPN). We have conducted tests using the NCS540 and ASR1002hx, and unfortunately, the Virtual Private LAN Service (VPLS) fails to establish connectivity. Below is the configuration of the NCS for your review.
so I can not find the problem of config 

l2vpn
 router-id 91.91.91.91
 pw-class vpls
  encapsulation mpls
   protocol ldp
   vccv verification-type none
   transport-mode ethernet
   ipv4 source 91.91.91.91
   
    bridge group 92
  bridge-domain 92
   interface TenGigE0/0/0/12.200
   !
   vfi 92
    neighbor 92.92.92.92 pw-id 95
     pw-class vpls
    !
 
mpls ldp
 router-id 91.91.91.91
 !
 interface TenGigE0/0/0/4.21
 !
 
interface TenGigE0/0/0/4.21
 mtu 1600
 ipv4 address 192.168.21.2 255.255.255.252
 encapsulation dot1q 21
!
 
interface TenGigE0/0/0/12.200
 encapsulation dot1q 200
!
 
 
show  l2vpn bridge-domain  bd-name 92 detail 
  List of VFIs:
    VFI 92 (up)
      PW: neighbor 92.92.92.92, PW ID 95, state is down ( remote standby ) (Transport LSP Down)
        PW class vpls, XC ID 0xc0000001
        Encapsulation MPLS, protocol LDP
        Source address 91.91.91.91
        PW type Ethernet, control word disabled, interworking none
        Sequencing not set
        Ignore MTU mismatch: Disabled
        Transmit MTU zero: Disabled
        LSP : Down
 
          MPLS         Local                          Remote                        
          ------------ ------------------------------ -------------------------
          Label        24001                          18                            
          Group ID     0x0                            0x0                           
          Interface    92                             unknown                       
          MTU          1500                           1500                          
          Control word disabled                       disabled                      
          PW type      Ethernet                       Ethernet                      
          VCCV CV type 0x0                            0x0                           
                       (none)                         (none)                        
          VCCV CC type 0x0                            0x0                           
                       (none)                         (none)                        
 
          ------------ ------------------------------ -------------------------
        MIB cpwVcIndex: 3221225473
        Create time: 07/05/2024 05:59:18 (6d01h ago)
        Last time status changed: 12/05/2024 12:15:01 (19:10:03 ago)
        MAC withdraw messages: sent 0, received 0
        Forward-class: 0
        Static MAC addresses:
      MAC learning: enabled
      Flooding:
        Broadcast & Multicast: enabled
        Unknown unicast: enabled
      MAC aging time: 300 s, Type: inactivity
      MAC limit: 64000, Action: none, Notification: syslog
      MAC limit reached: no, threshold: 75%
      MAC port down flush: enabled
      MAC Secure: disabled, Logging: disabled
      Split Horizon Group: none
  
  
show  l2vpn bridge-domain  bd-name 92 brief  
Legend: pp = Partially Programmed.
Bridge Group:Bridge-Domain Name  ID    State          Num ACs/up   Num PWs/up    Num PBBs/up Num VNIs/up
-------------------------------- ----- -------------- ------------ ------------- ----------- -----------
92:92                            0     up             1/0          1/0           0/0         0/0        
 
 
 
show  install  active  | i mpls
        ncs540-mpls-1.0.0.0-r792
        ncs540-mpls-1.0.0.0-r792
1 Reply 1

filopeter
Level 1
Level 1

please check the following output and config on the remote PE 

!

show l2vpn bridge-domain bd-name 92 detail 
List of VFIs:
VFI 92 (up)
PW: neighbor 92.92.92.92, PW ID 95, state is down ( remote standby ) (Transport LSP Down)