cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
Announcements
Choose one of the topics below to view our ISE Resources to help you on your journey with ISE

This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other best practices.

462
Views
15
Helpful
8
Replies
Beginner

SNS-3615 ISE Installation Stuck in started service enabling compressing ram with zram

Hi,

 

I was trying to reinstall the SNS-3615 with ISE v.2.6. But I'm stuck in "started service enabling compressing ram with zram", is this a normal behavior? I have attached the screenshots for reference.

 

Thanks,

John

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Beginner

Re: SNS-3615 ISE Installation Stuck in started service enabling compressing ram with zram

@Jason Kunst @Damien Miller 

thank you for yours answers.

 

It worked, I ahd to select another option among the 4 options I had to boot the new iso. ( version 2.6 on ISE Appliance 3655).

 

 

View solution in original post

8 REPLIES 8
Highlighted
Cisco Employee

Re: SNS-3615 ISE Installation Stuck in started service enabling compressing ram with zram

Please copy the ISO to a USB drive and use it to perform the install, if that is not what you are doing. It could seem stuck when the connection speed is slow.

Highlighted
Beginner

Re: SNS-3615 ISE Installation Stuck in started service enabling compressing ram with zram

Hi John,

 

I'm facing the same issue while installing an sns 3655 appliance.

How did you manage to correct that behavior ?

 

Thank you in advance,

 

Cadeau

Highlighted
VIP Advocate

Re: SNS-3615 ISE Installation Stuck in started service enabling compressing ram with zram

Can you confirm if you're trying to use the network KVM, or booting from usb media?

Which ISO file are you trying to boot? I ask because there is a 36x5 specific 2.4 ISO, and then a general 2.6 ISO.

Lastly, have you confirmed that the file md5/sha hash matches what cisco.com lists for the ISO you're trying to boot.


Highlighted
Cisco Employee

Re: SNS-3615 ISE Installation Stuck in started service enabling compressing ram with zram


@Damien Miller wrote:
Can you confirm if you're trying to use the network KVM, or booting from usb media?

Which ISO file are you trying to boot? I ask because there is a 36x5 specific 2.4 ISO, and then a general 2.6 ISO.

Lastly, have you confirmed that the file md5/sha hash matches what cisco.com lists for the ISO you're trying to boot.



If all else has failed please open tac case 

Highlighted
Beginner

Re: SNS-3615 ISE Installation Stuck in started service enabling compressing ram with zram

@Jason Kunst @Damien Miller 

thank you for yours answers.

 

It worked, I ahd to select another option among the 4 options I had to boot the new iso. ( version 2.6 on ISE Appliance 3655).

 

 

View solution in original post

Highlighted
Beginner

Re: SNS-3615 ISE Installation Stuck in started service enabling compressing ram with zram

What option did you pick ??

 

i ran into same issue 

Highlighted
Cisco Employee

Re: SNS-3615 ISE Installation Stuck in started service enabling compressing ram with zram

The boot option should be -- "Cisco ISE Installation (Keyboard/Monitor)"

Highlighted
Beginner

Re: SNS-3615 ISE Installation Stuck in started service enabling compressing ram with zram

Hi,

 

SNS 3615 can only support v2.4 or later. I faced this issue because I was trying to install v2.3. If you still face this issue using v2.4 or later, verify that the software is not corrupted. Check its MD5 hash.

 

Hope this helps.