Re: 2800 series router snmp oid required to copy config via tftp

iswift · ‎09-28-2011

Hi

I have a 2801 running

c2801-spservicesk9-mz.124-3g.bin

According to the Cisco IOS MIB locator the image supports OLD-CISCO-SYSTEM-MIB

I have tried

.1.3.6.1.4.1.9.2.1.55 etc to set server IP address and the filename string but without any luck.

e.g.

Reason: (noSuchName) There is no such variable name in this MIB.

Failed object: iso.3.6.1.4.1.9.2.1.55.a.b.c.d (where a.b.c.d is the server IP)

I have also tried the method similar to that for Cat 3550 switches where you create a table of entries to define the transfer paramaters then activate the transfer (I think the CISCO-CONFIG-COPY-MIB)

e.g.

https://www.cisco.com/en/US/tech/tk648/tk362/technologies_configuration_example09186a0080094aa6.shtml#intro

C:\>snmpset -v 1 -c private <device name> ccCopyProtocol.<random number> integer 1   ! 1 = tftp
ccCopySourceFileType.<Random number> integer 1     ! 1 = networkFile
ccCopyDestFileType.<Random number> integer 3     ! 3 = startup & 4 = running
ccCopyServerAddress.<Random number> ipaddress "<server ip address>"
ccCopyFileName. <Random number> octetstring "<file name>"
ccCopyEntryRowStatus.<Random number> integer 4     ! 4 = createAndGo, or 1 = Active

To write net have the source as running (4) and the dest as network (1)

ccCopySourceFileType.<Random number> integer 4

ccCopyDestFileType.<Random number> integer 1

Clean up at the end - destroy .14 with the value of 6.

example output : -

-- earlier output omitted --

Error in packet.

Reason: (noSuchName) There is no such variable name in this MIB.

Failed object: iso.3.6.1.4.1.9.9.96.1.1.1.1.4.111

Error in packet.

Error in packet.
Reason: (noSuchName) There is no such variable name in this MIB.
Failed object: iso.3.6.1.4.1.9.9.96.1.1.1.1.5.111

Error in packet.

Reason: (noSuchName) There is no such variable name in this MIB.

Failed object: iso.3.6.1.4.1.9.9.96.1.1.1.1.6.111

Can anyone help with the oids to do a write net using SNMP with a 2800 series integrated services router ?

Ian.

ccube · ‎09-28-2011

This tech doc discusses how to perform:

http://www.cisco.com/en/US/customer/tech/tk648/tk362/technologies_configuration_example09186a0080094aa6.shtml

The key is to first destroy the intended row first, then specify all required oids in a single set unless you are using create and wait.

Like snmpset -v2c -cpublic oid1 oid2 oid3 and so on.

If you need a full working example, let me know and I will perform the same on my router and let you see it all...

Hth,

Cary

Sent from Cisco Technical Support iPad App

iswift · ‎09-29-2011

Thank you Cary,

So are you saying the CONFIG-COPY-MIB is in fact the right one ?

If so I see what you are saying.

However there is no exisitng row to delete.

If I walk

.1.3.6.1.4.1.9.9.96

it is empty

C:\>snmpwalk LSBEEHIVE_VG1 xxxxxxxxxx .1.3.6.1.4.1.9.9.96

I think there may be an issue with this device then as I cannot implement the following. We will administer the device locally, we just wanted to get round having to do a password recovery.

C:\>snmpset -v1 -c RW_string Hostname_VG1 .1.3.6.1.4.1.9.9.96.1.1.1.1.2.128 i 1
.1.3.6.1.4.1.9.9.96.1.1.1.1.3.128 i 4 .1.3.6.1.4.1.9.9.96.1.1.1.1.4.128 i 1 .1.
3.6.1.4.1.9.9.96.1.1.1.1.5.128 a 137.223.74.14 .1.3.6.1.4.1.9.9.96.1.1.1.1.6.128
s Hostname_VG1.txt .1.3.6.1.4.1.9.9.96.1.1.1.1.14.128 i 4
Cannot find module (IP-MIB): At line 0 in (none)
Cannot find module (IF-MIB): At line 0 in (none)
Cannot find module (TCP-MIB): At line 0 in (none)
Cannot find module (UDP-MIB): At line 0 in (none)
Cannot find module (HOST-RESOURCES-MIB): At line 0 in (none)
Cannot find module (SNMPv2-MIB): At line 0 in (none)
Cannot find module (SNMPv2-SMI): At line 0 in (none)
Cannot find module (NOTIFICATION-LOG-MIB): At line 0 in (none)
Cannot find module (UCD-SNMP-MIB): At line 0 in (none)
Cannot find module (UCD-DEMO-MIB): At line 0 in (none)
Cannot find module (SNMP-TARGET-MIB): At line 0 in (none)
Cannot find module (NET-SNMP-AGENT-MIB): At line 0 in (none)
Cannot find module (DISMAN-EVENT-MIB): At line 0 in (none)
Cannot find module (SNMP-VIEW-BASED-ACM-MIB): At line 0 in (none)
Cannot find module (SNMP-COMMUNITY-MIB): At line 0 in (none)
Cannot find module (UCD-DLMOD-MIB): At line 0 in (none)
Cannot find module (SNMP-FRAMEWORK-MIB): At line 0 in (none)
Cannot find module (SNMP-MPD-MIB): At line 0 in (none)
Cannot find module (SNMP-USER-BASED-SM-MIB): At line 0 in (none)
Cannot find module (SNMP-NOTIFICATION-MIB): At line 0 in (none)
Cannot find module (SNMPv2-TM): At line 0 in (none)
Error in packet.
Reason: (noSuchName) There is no such variable name in this MIB.
Failed object: iso.3.6.1.4.1.9.9.96.1.1.1.1.2.128

Thanks for your reply.

Rgds

Ian

ccube · ‎09-29-2011

Hi Ian,

Well, it would seem that the IOS version you are running does not support the CISCO-CONFIG-COPY-MIB. This would mean you would have to fallback to the OLD-CISCO-SYSTEM-MIB to pull this off. See the following tech doc on using that MIB for this purpose:

http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a008009463e.shtml

Here is the MIBS supported by the image you are running:

c2801-spservicesk9-mz.124-3g.bin MIBS Supported in this Image

ADSL-DMT-LINE-MIB

ADSL-LINE-MIB

ATM-MIB

BRIDGE-MIB

CISCO-AAA-SERVER-MIB

CISCO-AAA-SESSION-MIB

CISCO-AAL5-MIB

CISCO-ACCESS-ENVMON-MIB

CISCO-ADSL-DMT-LINE-MIB

CISCO-ATM-EXT-MIB

CISCO-ATM-PVCTRAP-EXTN-MIB

CISCO-BULK-FILE-MIB

CISCO-BUS-MIB

CISCO-CALL-APPLICATION-MIB

CISCO-CALL-HISTORY-MIB

CISCO-CAR-MIB

CISCO-CAS-IF-MIB

CISCO-CDP-MIB

CISCO-CIRCUIT-INTERFACE-MIB

CISCO-CLASS-BASED-QOS-MIB

CISCO-COMPRESSION-SERVICE-ADAPTER-MIB

CISCO-CONFIG-MAN-MIB

CISCO-DATA-COLLECTION-MIB

CISCO-DIAL-CONTROL-MIB

CISCO-DSL-CPE-MIB

CISCO-DSP-MGMT-MIB

CISCO-EMBEDDED-EVENT-MGR-MIB

CISCO-ENTITY-ASSET-MIB

CISCO-ENTITY-EXT-MIB

CISCO-ENTITY-VENDORTYPE-OID-MIB

CISCO-ENVMON-MIB

CISCO-FLASH-MIB

CISCO-FRAME-RELAY-MIB

CISCO-FTP-CLIENT-MIB

CISCO-GPRS-GTP-MIB

CISCO-H323-TC-MIB

CISCO-HSRP-EXT-MIB

CISCO-HSRP-MIB

CISCO-ICSUDSU-MIB

CISCO-IETF-ATM2-PVCTRAP-MIB

CISCO-IETF-ATM2-PVCTRAP-MIB-EXTN

CISCO-IF-EXTENSION-MIB

CISCO-IMAGE-MIB

CISCO-IP-STAT-MIB

CISCO-IPMROUTE-MIB

CISCO-ISDN-MIB

CISCO-ISDNU-IF-MIB

CISCO-LEC-DATA-VCC-MIB

CISCO-LEC-EXT-MIB

CISCO-LECS-MIB

CISCO-LES-MIB

CISCO-MEMORY-POOL-MIB

CISCO-MOBILE-IP-MIB

CISCO-MVPN-MIB

CISCO-NBAR-PROTOCOL-DISCOVERY-MIB

CISCO-NETFLOW-MIB

CISCO-NTP-MIB

CISCO-OSPF-MIB

CISCO-OSPF-TRAP-MIB

CISCO-PIM-MIB

CISCO-PING-MIB

CISCO-POP-MGMT-MIB

CISCO-PPPOE-MIB

CISCO-PROCESS-MIB

CISCO-PRODUCTS-MIB

CISCO-QUEUE-MIB

CISCO-RAS-MIB

CISCO-REAL-TIME-CLOCK-MIB

CISCO-RMON-CONFIG-MIB

CISCO-RMON-SAMPLING-MIB

CISCO-RTTMON-MIB

CISCO-SAA-APM-MIB

CISCO-SIP-UA-MIB

CISCO-SMI

CISCO-SNAPSHOT-MIB

CISCO-SNMP-TARGET-EXT-MIB

CISCO-STACKMAKER-MIB

CISCO-SYSLOG-MIB

CISCO-TC

CISCO-TCP-MIB

CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB

CISCO-VLAN-MEMBERSHIP-MIB

CISCO-VOICE-ANALOG-IF-MIB

CISCO-VOICE-ATM-DIAL-CONTROL-MIB

CISCO-VOICE-COMMON-DIAL-CONTROL-MIB

CISCO-VOICE-DIAL-CONTROL-MIB

CISCO-VOICE-DNIS-MIB

CISCO-VOICE-ENABLED-LINK-MIB

CISCO-VOICE-FR-DIAL-CONTROL-MIB

CISCO-VOICE-IF-MIB

CISCO-VOICE-NUMBER-EXPANSION-MIB

CISCO-VOICE-URI-CLASS-MIB

CISCO-VPDN-MGMT-EXT-MIB

CISCO-VPDN-MGMT-MIB

CISCO-VSIMASTER-MIB

CISCO-VTP-MIB

CISCO-WRED-MIB

DIAL-CONTROL-MIB

DS1-MIB

ETHERLIKE-MIB

EVENT-MIB

EXPRESSION-MIB

FUNI-MIB

HC-RMON-MIB

HDSL2-SHDSL-LINE-MIB

IF-MIB

IGMP-STD-MIB

INT-SERV-GUARANTEED-MIB

INT-SERV-MIB

IP-FORWARD-MIB

IPMROUTE-STD-MIB

ISDN-MIB

LAN-EMULATION-CLIENT-MIB

MIP-MIB

MPLS-LDP-MIB

MPLS-LSR-MIB

MPLS-TE-MIB

MPLS-VPN-MIB

MSDP-MIB

OLD-CISCO-CHASSIS-MIB

OLD-CISCO-CPU-MIB

OLD-CISCO-FLASH-MIB

OLD-CISCO-INTERFACES-MIB

OLD-CISCO-IP-MIB

OLD-CISCO-MEMORY-MIB

OLD-CISCO-SYSTEM-MIB

OLD-CISCO-TCP-MIB

OLD-CISCO-TS-MIB

OSPF-MIB

OSPF-TRAP-MIB

PIM-MIB

Q-BRIDGE-MIB

RFC1213-MIB

RFC1231-MIB

RFC1315-MIB

RFC1381-MIB

RFC1382-MIB

RFC1406-MIB

RMON-MIB

RMON2-MIB

RS-232-MIB

RSVP-MIB

SMON-MIB

SNMP-FRAMEWORK-MIB

SNMP-NOTIFICATION-MIB

SNMP-PROXY-MIB

SNMP-TARGET-MIB

SNMP-USM-MIB

SNMP-VACM-MIB

SONET-MIB

SOURCE-ROUTING-MIB

TCP-MIB

UDP-MIB

VRRP-MIB

XGCP-MIB

Hope this helps,

Cary

iswift · ‎09-29-2011

Thanks for the quick response.

See top of post, OLD-CISCO-SYSTEM-MIB

isn't working either.

" .1.3.6.1.4.1.9.2.1.55 etc to set server IP address and the filename string but without any luck."

i.e. the writeNet oid

e.g.

C:\>snmpset -v1 -c rw-string RTR_VG1 .1.3.6.1.4.1.9.2.1.55.137.223.74.14 s
RTR_VG1.txt
Cannot find module (IP-MIB): At line 0 in (none)
Cannot find module (IF-MIB): At line 0 in (none)
Cannot find module (TCP-MIB): At line 0 in (none)
Cannot find module (UDP-MIB): At line 0 in (none)
Cannot find module (HOST-RESOURCES-MIB): At line 0 in (none)
Cannot find module (SNMPv2-MIB): At line 0 in (none)
Cannot find module (SNMPv2-SMI): At line 0 in (none)
Cannot find module (NOTIFICATION-LOG-MIB): At line 0 in (none)
Cannot find module (UCD-SNMP-MIB): At line 0 in (none)
Cannot find module (UCD-DEMO-MIB): At line 0 in (none)
Cannot find module (SNMP-TARGET-MIB): At line 0 in (none)
Cannot find module (NET-SNMP-AGENT-MIB): At line 0 in (none)
Cannot find module (DISMAN-EVENT-MIB): At line 0 in (none)
Cannot find module (SNMP-VIEW-BASED-ACM-MIB): At line 0 in (none)
Cannot find module (SNMP-COMMUNITY-MIB): At line 0 in (none)
Cannot find module (UCD-DLMOD-MIB): At line 0 in (none)
Cannot find module (SNMP-FRAMEWORK-MIB): At line 0 in (none)
Cannot find module (SNMP-MPD-MIB): At line 0 in (none)
Cannot find module (SNMP-USER-BASED-SM-MIB): At line 0 in (none)
Cannot find module (SNMP-NOTIFICATION-MIB): At line 0 in (none)
Cannot find module (SNMPv2-TM): At line 0 in (none)
Error in packet.
Reason: (noSuchName) There is no such variable name in this MIB.
Failed object: iso.3.6.1.4.1.9.2.1.55.137.223.74.14

Thanks

Ian