Cisco Community
English
Register
COMMUNITY HELPING COMMUNITY - With your Community actions and contributions, we will donate up to $10,000 to UNICEF by end of January- PARTICIPATE
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
342
Views
0
Helpful
2
Replies
Highlighted
Zohaib Hussain
Beginner
Beginner
‎05-18-2010 11:32 PM
‎05-18-2010 11:32 PM

Cisco LMS 3.2

I have cisco LMS 3.2 installed on the virtual machine. The problem i am facing is that i cannot detect devices automatically behind other vendor devices. I can ping the devices and i can also add manually but i need LMS to discover them automatically because of the large number of devices.

Labels:
0 Helpful
Reply
1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Joe Clarke
Hall of Fame Cisco Employee Hall of Fame Cisco Employee
Hall of Fame Cisco Employee
‎05-19-2010 04:13 PM
‎05-19-2010 04:13 PM

If you can ping them, and if you can communicate with them via SNMP, you can configure the Ping Sweep Discovery module to find these devices automatically.  Just specify some subnet ranges to ping.  See my document on understanding CSDiscovery for more details:

https://supportforums.cisco.com/docs/DOC-9005

View solution in original post

0 Helpful
Reply
2 REPLIES 2
Highlighted
Joe Clarke
Hall of Fame Cisco Employee Hall of Fame Cisco Employee
Hall of Fame Cisco Employee
‎05-19-2010 04:13 PM
‎05-19-2010 04:13 PM

If you can ping them, and if you can communicate with them via SNMP, you can configure the Ping Sweep Discovery module to find these devices automatically.  Just specify some subnet ranges to ping.  See my document on understanding CSDiscovery for more details:

https://supportforums.cisco.com/docs/DOC-9005

View solution in original post

0 Helpful
Reply
Highlighted
Zohaib Hussain
Beginner
Beginner
In response to Joe Clarke
‎05-21-2010 10:23 PM
‎05-21-2010 10:23 PM

Thnx Joe, it helped me alot. Found the problem in SNMP configuration in devices. Now everything is working. The Document is also very helpfull.

0 Helpful
Reply
Latest Contents
Use Serviceability Features to Troubleshoot your Cat9K as a ...
Created by ciscomoderator on 11-27-2020 10:37 PM
0
0
0
0
[ The Discussion forum will be published on December 1st ] Take the opportunity to reach out to our expert and discuss best practices regarding on how to troubleshoot a live network and identify the root cause easily. Learn more about Serviceability and h... view more
Remote Workforce Routing Solution - Cisco SD-WAN
Created by Randeep Singh on 11-25-2020 11:25 PM
2
10
2
10
Goal Network Admin To provide a solution to quickly setup a router at a remote location that supports WiFi and provides instant internet access using LTE as a transport while deploying with Cisco SD-WAN. Remote Worker Plug the router to a power sou... view more
EEM making a script more dynamic and automated
Created by fsebera on 11-25-2020 12:18 PM
0
0
0
0
Hello!I'm looking for a way to make my EEM script more dynamic and automated for my environment.  This is what I have - basically I just capture the 4 IPSec peer IP addresses of each neighbor and insert this data into 4 different variables. ... view more
Nexus 9k tcpdump vs ethanalyzer
Created by ICANG on 11-25-2020 03:23 AM
1
0
1
0
Hi all,I have a couple of Nexus9k switches. I need to get tcpdump from the physical  interface which connected to the server. I'm looking for a specific protocol on tcpdump so that which feature should I use? I asked that because I couldn't full... view more
Building AAR policies
Created by networkhelp1 on 11-24-2020 09:54 AM
0
0
0
0
We are building out our first few AAR polices and are running into an error message.Built Global Policy with SLA class and traffic rules for voice traffic, attached to to the sites and VPN we needed, no issue. Building a second policy for management ... view more
Content for Community-Ad