04-07-2010 04:43 AM
We have lms 3.2 configured at our organisation.But i am not able to initialise ANI server.The process is always down and not coming up.
EDS and anidatabase processes are up.But ani server is not coming up due to which i am not able to access the CAmpus manager.Please reply asap.
04-07-2010 11:08 PM
Post the output of the pdshow command from the server as well as the ani.log and ANIServer.log.
--
Please support CSC Helps Haiti
https://supportforums.cisco.com/docs/DOC-8895
https://supportforums.cisco.com
04-09-2010 09:59 PM
04-09-2010 11:40 PM
Post the NMSROOT/campus/etc/cwsi/ANIServer.properties.
04-10-2010 03:17 AM
Before this below was the output then i followed one doc im attaching it now and changed as per the instructions.Il paste the current files also.
EnablePurgeArchives=ON
PurgeArchivesOlderThan=180
EnablePurgeJobs=ON
PurgeJobsOlderThan=180
EnableCMPurgeArchives=ON
I have attached the doc which i followed to change the aniserver file but still did not initialise the aniserver.
Aniserver issue .pdf is the file i followed to change the corrupted aniserver file.
aniserver.properties is the file attached with current settings after changing.
04-11-2010 10:55 AM
These properties were not the problem. You had messed up the module path. Replace your version with this attached one. Then restart Daemon Manager, and you should be good to go.
--
Please support CSC Helps Haiti
https://supportforums.cisco.com/docs/DOC-8895
https://supportforums.cisco.com
04-12-2010 06:06 AM
I have followed the steps and restored the configs but still ani server is down.Please advise
04-12-2010 10:04 AM
Post the new pdshow output, ani.log, and ANIServer.log. Repost the ANIServer.properties that you now have in NMSROOT/campus/etc/cwsi.
04-12-2010 10:01 PM
04-13-2010 11:51 AM
04-13-2010 11:56 PM
Thankyou the Ani Server is up but it is running with busy flagset.The other thing is the Discrepencies reports and violations report is not showing anything.
The respone time of the server is ver y slow
04-14-2010 09:04 AM
Running with busy flag set is the normal state for ANIServer. See my Daemon Cheat Sheet at https://supportforums.cisco.com/docs/DOC-8798 for more on what the healthy daemon states should be.
The Discrepancies and BPD will only be populated after a Campus Data Collection is run. It can take up to 30 minutes after a restart of Daemon Manager before the daemons calm down, and the system becomes responsive.
04-16-2010 10:01 PM
Thankyou very much ,The Campus Manager lists are populated again.One more thing i wanted to Know regarding MS Tcp loopback Interface.My Management software is showing high utilization on this MS tcp loopback interface of 10 mb on Cisco works Server.
04-16-2010 11:46 PM
LMS does a lot of internal communication (i.e. inter-process communication) on 127.0.0.1. Therefore, it would not be uncommon for one to see high loopback traffic.
--
Please support CSC Helps Haiti
https://supportforums.cisco.com/docs/DOC-8895
https://supportforums.cisco.com
09-09-2012 11:37 PM
hi Joseph,
recently I have faced the same issue and after changing the properties file ANI server started but now i am getting the error "There may be possible ACS config mismatch " where as i have not changed the ACS settings. Could u pls help me out .
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide