cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1073
Views
0
Helpful
1
Replies

Deprecated IP SLA Commands during IOS Upgrade - c3845 12.4(12) to 15.1(4)

michael.lorincz
Level 4
Level 4

I recently upgraded a customer's 3845 voice gateway from 12.4 to 15.1 but received some deprecated messages during boot. The following section did not 'take'. I spent a little time finding the new sytnax and I believe I revised the first section properly but the second line (shown in red) did not want to take. 

I'm hoping someone familiar with IP SLA can easily identify the correct new syntax I should be using the accomplish the spirit of the original configuration. Any help would be appreciated!

 

OLD CONFIG
ip sla monitor 100
 type echo protocol ipIcmpEcho 192.168.12.1 source-ipaddr 12.XX.XXX.XXX
 request-data-size 24
 timeout 60000
 threshold 200
 owner OpManager
ip sla monitor reaction-configuration 100 connection-loss-enable verify-error-enable timeout-enable threshold-falling 150 threshold-type immediate action-type trapOnly


NEW Config
ip sla 100
 icmp-echo 192.168.12.1 source-ip 12.XX.XXX.XXX
 request-data-size 24
 timeout 60000
 threshold 200
 owner OpManager
ip sla reaction-configuration 100 react ???????

 

TES-CA-IRV-R01(config)#ip sla reaction-configuration 100 ?
  react  Reaction variable to be configured

TES-CA-IRV-R01(config)#ip sla reaction-configuration 100 reac
TES-CA-IRV-R01(config)#ip sla reaction-configuration 100 react ?
  rtt          Round Trip Time
  timeout      Timeout
  verifyError  Verify Error

TES-CA-IRV-R01(config)#ip sla reaction-configuration 100 ?     
  react  Reaction variable to be configured

TES-CA-IRV-R01(config)#ip sla reaction-configuration 100 er
TES-CA-IRV-R01(config)#ip sla reaction-configuration 100 re
TES-CA-IRV-R01(config)#ip sla reaction-configuration 100 react ?
  rtt          Round Trip Time
  timeout      Timeout
  verifyError  Verify Error

1 Accepted Solution

Accepted Solutions

Vinod Arya
Cisco Employee
Cisco Employee

Effective with Cisco IOS Release 12.3(14)T and 12.2(31)SB2, the rtr reaction-configuration command is replaced by the ip sla monitor reaction-configuration command. Effective with Cisco IOS Release 12.2(33)SRB, the rtr reaction-configuration command is replaced by the ip sla reaction-configuration command.

You can check following document to see IP SLA Reaction-configuration command :

Example Configuring an IP SLAs Reaction Configuration

Example Verifying an IP SLAs Reaction Configuration

HTH

Vinod

 

-Thanks Vinod **Rating Encourages contributors, and its really free. **

View solution in original post

1 Reply 1

Vinod Arya
Cisco Employee
Cisco Employee

Effective with Cisco IOS Release 12.3(14)T and 12.2(31)SB2, the rtr reaction-configuration command is replaced by the ip sla monitor reaction-configuration command. Effective with Cisco IOS Release 12.2(33)SRB, the rtr reaction-configuration command is replaced by the ip sla reaction-configuration command.

You can check following document to see IP SLA Reaction-configuration command :

Example Configuring an IP SLAs Reaction Configuration

Example Verifying an IP SLAs Reaction Configuration

HTH

Vinod

 

-Thanks Vinod **Rating Encourages contributors, and its really free. **
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Innovations in Cisco Full Stack Observability - A new webinar from Cisco