My router is cisco 881-w my server pc ip address is 10.10.10.3, but my wireless clients from 10.10.12.1 till 10.10.12.20, how can i see each other computers in windows network... I can ping computers, but i can't browse... I preffer to use cisco configuration proffesional v2.1, but also i'm learning CLI...
but i can't ping wireless to LAN eg "ping SERVER" but when i ping my server ip adress eg "ping 10.10.10.3" result is successfully
Current configuration : 7126 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname r_LIEPAJAS_7VSK_111
!
boot-start-marker
boot-end-marker
!
logging message-counter syslog
logging buffered 51200 warnings
ip source-route
!
ip dhcp pool ccp-pool
import all
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
netbios-name-server 7.7.7.0
dns-server 80.233.223.27 6.6.6.0
!
ip dhcp pool pool-2
import all
network 10.10.11.0 255.255.255.0
default-router 10.10.11.1
!
ip dhcp pool pool-3
import all
network 10.10.12.0 255.255.255.0
default-router 10.10.12.1
netbios-name-server 7.7.7.0
dns-server 80.233.223.27 6.6.6.0
!
ip dhcp pool Serveris
hardware-address 78e7.d186.99c2
client-name Serveris
!
!
ip cef
ip domain name l7vsk.lv
ip name-server 10.10.0.100
ip name-server 80.233.223.27
ip ddns update method sdm_ddns1
DDNS both
!
!
!
!
!
archive log config
hidekeys
!
!
!
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
description $ETH-WAN$
ip dhcp client update dns server none
ip ddns update sdm_ddns1
ip address dhcp client-id FastEthernet4
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
!
interface wlan-ap0
description Service module interface to manage the embedded AP
ip address 10.10.11.1 255.255.255.0
arp timeout 0
!
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
switchport mode trunk
!
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
ip address 10.10.10.1 255.255.255.0
ip helper-address 10.10.10.255
ip directed-broadcast
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1452
!
interface Vlan2
ip address 10.10.12.1 255.255.255.0
ip helper-address 10.10.12.255
no ip redirects
no ip unreachables
ip directed-broadcast
no ip proxy-arp
ip nat inside
ip virtual-reassembly
!
ip forward-protocol nd
ip route 10.10.10.0 255.255.255.0 Vlan2
ip route 10.10.12.0 255.255.255.0 Vlan1
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
ip nat pool pool 10.10.10.0 10.10.10.254 netmask 255.255.255.0
ip nat pool pool2 10.10.12.0 10.10.12.254 netmask 255.255.255.0
ip nat inside source list 2 interface FastEthernet4 overload
ip nat inside source list 3 interface FastEthernet4 overload
ip nat inside source list 4 interface FastEthernet4 overload
ip nat inside source list netbios pool pool2 overload
!
ip access-list extended netbios
remark enable netbios
remark CCP_ACL Category=2
remark netbios
permit udp any eq netbios-ns any eq netbios-ns
!
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 10.10.10.0 0.0.0.7
access-list 2 remark CCP_ACL Category=2
access-list 2 permit 10.10.10.0 0.0.0.255
access-list 3 remark CCP_ACL Category=2
access-list 3 permit 10.10.11.0 0.0.0.255
access-list 4 remark CCP_ACL Category=2
access-list 4 permit 10.10.12.0 0.0.0.255
access-list 23 permit 10.10.10.0 0.0.0.7
no cdp run
!
!
!
!
-----------------------------------------------------------------------^C
!
line con 0
login local
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
access-class 23 in
privilege level 15
login local
transport input telnet ssh
!
scheduler max-task-time 5000
end
