05-07-2020 03:58 PM
not sure if there is something im missing or if there is a problem with the chassis or module I have tried other module of same type no difference
not sure if im missing a set to configure this or possible chassis problem
F241.8.22-2921-1#show inv
NAME: "CISCO2921/K9", DESCR: "CISCO2921/K9 chassis, Hw Serial#: FTX1720AJP9, Hw Revision: 1.0"
PID: CISCO2921/K9 , VID: V08 , SN:
NAME: "PVDM3 DSP DIMM with 256 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 256 Channels"
PID: PVDM3-256 , VID: V01 , SN:
NAME: "SM-ES2-16-P: EtherSwitch SM L2 + PoE + 15 10/100 + 1 10/100/1000 on Slot 1", DESCR: "SM-ES2-16-P: EtherSwitch SM L2 + PoE + 15 10/100 + 1 10/100/1000"
PID: SM-ES2-16-P , VID: V01 , SN:
NAME: "C2921/C2951 AC-POE Power Supply", DESCR: "C2921/C2951 AC-POE Power Supply"
PID: PWR-2921-51-POE , VID: V03 , SN:
F241.8.22-2921-1#show ip int br
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 unassigned YES TFTP up up
GigabitEthernet0/0 10.207.171.197 YES DHCP up up
GigabitEthernet0/1 unassigned YES NVRAM down down
GigabitEthernet0/2 unassigned YES NVRAM down down
F241.8.22-2921-1#
F241.8.22-2921-1#show version
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.4(3)M3, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Fri 05-Jun-15 13:24 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M16, RELEASE SOFTWARE (fc1)
<--- OMITTED --->
Cisco CISCO2921/K9 (revision 1.0) with 2244608K/114688K bytes of memory.
Processor board ID FTX1720AJP9
3 Gigabit Ethernet interfaces
1 terminal line
1 Virtual Private Network (VPN) Module
1 cisco Embedded service engine(s)
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
245448K bytes of ATA System CompactFlash 0 (Read/Write)
<--- OMITTED --->
Technology Package License Information for Module:'c2900'
------------------------------------------------------------------------
Technology Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------------
ipbase ipbasek9 Permanent ipbasek9
security securityk9 Permanent securityk9
uc uck9 Permanent uck9
data datak9 RightToUse datak9
NtwkEss None None None
CollabPro None None None
Configuration register is 0x2102
F241.8.22-2921-1#
F241.8.22-2921-1#show running-config
Building configuration...
<--- OMITTED --->
version 15.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname F241.8.22-2921-1
!
boot-start-marker
boot system flash0:c2900-universalk9-mz.SPA.154-3.M3.bin
boot-end-marker
!
!
!
no aaa new-model
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
ip cef
no ipv6 cef
!
multilink bundle-name authenticated
!
!
!
!
!
!
cts logging verbose
!
!
voice-card 0
!
!
!
!
!
!
!
!
license udi pid CISCO2921/K9 sn FTX1720AJP9
license accept end user agreement
license boot module c2900 technology-package securityk9
license boot module c2900 technology-package datak9
hw-module pvdm 0/0
!
hw-module sm 1
!
!
!
<--- OMITTED --->
!
redundancy
!
!
!
!
!
ip ftp source-interface GigabitEthernet0/0
ip tftp source-interface GigabitEthernet0/0
!
!
!
!
!
!
!
!
!
!
interface Embedded-Service-Engine0/0
no ip address
!
interface GigabitEthernet0/0
ip address dhcp
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
!
interface GigabitEthernet0/2
no ip address
duplex auto
speed auto
!
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
<--- OMITTED --->
!
!
!
!
control-plane
!
!
!
!
!
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
!
!
!
!
!
!
gatekeeper
shutdown
!
!
!
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
login local
transport input telnet ssh
!
scheduler allocate 20000 1000
!
end
Solved! Go to Solution.
05-07-2020 04:14 PM
05-07-2020 04:14 PM
05-13-2020 08:41 PM
Thanks for that and after reading it seems to be the issue or might have been a bad slot as when i moved it over to my backup chassis it came right up so i will have to test my other chassis to see if it is a card or the slot in my chassis
Thanks again
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide