Smartport - 1142 and 3502

[dtom]

Does Smartport support the 1142 AP and the 3502 AP?  It keeps comming up as a Router device - CISCO_ROUTER_EVENT

The 1131 AP work fine.

[dtom]

We finally had a chance to update the IOS to 12.2(55)SE8.  The 1142N is still causing the CISCO_ROUTER_EVENT to trigger.

Here is some more info:

cs-VangPao-M-C#sh run | b 7/0/1

interface GigabitEthernet7/0/1

macro description CISCO_ROUTER_EVENT

!

================================================================================

cs-VangPao-M-C#sh ver

Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE8,

RELEASE SOFTWARE (fc2)

Technical Support:

http://www.cisco.com/techsupport

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Wed 26-Jun-13 09:56 by prod_rel_team

Image text-base: 0x00003000, data-base: 0x02800000

Device ID: VangPao107_APa44c.117f.8a77
Entry address(es):
  IP address: 10.20.0.118
Platform: cisco AIR-LAP1142N-A-K9,  Capabilities: Router Trans-Bridge
Interface: GigabitEthernet7/0/1,  Port ID (outgoing port): GigabitEthernet0.1
Holdtime : 174 sec

Version :
Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 15.2(4)JA1, RELEASE S
OFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 23:25 by prod_rel_team

advertisement version: 2
Duplex: full
Power drawn: 15.400 Watts
Power request id: 9536, Power management id: 2
Power request levels are:15400 14500 0 0 0
Management address(es):

cs-VangPao-M-C#sh ver

Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE8,

RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Wed 26-Jun-13 09:56 by prod_rel_team

Image text-base: 0x00003000, data-base: 0x02800000

================================================================================

Device ID: VangPao107_APa44c.117f.8a77
Entry address(es):
  IP address: 10.20.0.118
Platform: cisco AIR-LAP1142N-A-K9,  Capabilities: Router Trans-Bridge
Interface: GigabitEthernet7/0/1,  Port ID (outgoing port): GigabitEthernet0.1
Holdtime : 174 sec

Version :
Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 15.2(4)JA1, RELEASE S
OFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 23:25 by prod_rel_team

advertisement version: 2
Duplex: full
Power drawn: 15.400 Watts
Power request id: 9536, Power management id: 2
Power request levels are:15400 14500 0 0 0
Management address(es):

================================================================================

Any other thoughts here?

[Joe Clarke]

The problem is the "Router" capability of the AP.  I found a bug that was unreproducible that hinted controller version may have something to do with this.  I'm not sure what controller version you're using, but perhaps a change in controller code will fix this.  Unfortunately, I couldn't find any more specifics on this as the one customer that encountered it (in controller 7.3.101 code) just used the CISCO_ROUTER_EVENT as a workaround.