Access problem

[fmartos]

First of all, sorry for my English. My problem is:

I have an ASA5510 Firewall with one router in the outside interface doing NAT (It is also a VPN Server) and another one in inside interface. When I tried to open a remote desktop from Internet using VPN to an internal PC, this PC does not respond, but I launch a Ping command from the internal PC to the outside firewall interface and then I relaunch the remote desktop connection, it works.

Thanks in advance. Regards.

[Jennifer Halim]

Can you please share the output of the following show commands:

show run interface

show run nat

show run static

show run global

as well as the ip address of the remote desktop server. Thanks.

[fmartos]

Thank you, Jennifer, for your quickly answer. This is the output of commands:

SA5510# sh run inter
!
interface Ethernet0/0
nameif Outside
security-level 0
ip address 192.168.101.2 255.255.255.252
!
interface Ethernet0/1
nameif Inside
security-level 100
ip address 192.168.102.1 255.255.255.252
!
interface Ethernet0/2
nameif DMZ
security-level 50
ip address 192.168.50.1 255.255.255.0
!
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
!
interface Management0/0
nameif management
security-level 100
ip address Management-Interface 255.255.255.0
management-only

ASA5510-CEPC# sh run nat
nat (Inside) 0 0.0.0.0 0.0.0.0
ASA5510-CEPC#

ASA5510-CEPC# sh run static
ASA5510-CEPC#

ASA5510-CEPC# sh run global
ASA5510-CEPC#

Please, find attach a file with a scheme of the solution. Thanks a lot for your help.

[Jennifer Halim · Accepted solution]

The diagram was not uploaded - CiscoExpert.jpg (75.9 K) QUEUED

As per the configuration, you have the following configured:

nat (Inside) 0 0.0.0.0 0.0.0.0

which is a dynamic NAT exemption.

To be able to initiate the connection from the outside towards the inside, please kindly change the above nat statement to the following:

access-list nonat permit ip any any

nat (Inside) 0 access-list nonat

no nat (Inside) 0 0.0.0.0 0.0.0.0

"clear xlate" after the above changes, and try to initiate the RDP connection again from the VPN.

[fmartos]

Thank very much, Jennifer. A personal problem requires my attention out of the office. I will do on Monday, I hope, and I will inform you about the result.This is the graphic. Talk to you.

[Nagaraja Thanthry]

Hello,

How did you configure NAT on the router? Have you configured a policy-NAT in the router that allows the internal hosts to go un-natted to the VPN clients? Can you share your NAT configurations on the router here?

Regards,

NT

[fmartos]

Hi, Nagaraja; as you requested, this is the NAT configuration. I have included the Easy VPN configuration. As you can see I have deleted the rest of configuration:

cisco2821#sh run
Building configuration...

deleted
!
version 12.4
parser config cache interface
parser config interface
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
service sequence-numbers
!
hostname cisco2821
!
boot-start-marker
boot-end-marker
!
logging buffered 512000 warnings
!
aaa new-model
!
!
aaa authentication login Remotos local
aaa authorization exec default local
aaa authorization network Remotos local
!
!
deleted
!
deleted
!
!
deleted
username soft_vpn_client password 7 1235040541085C0E7A39772F3F3479030607
!
!
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
!
deleted
!
crypto isakmp client configuration group Serikat
key xxxxxxxxxxxxxxxxxxxxxxxxxx
pool Serikat
acl 121
save-password
max-users 1
max-logins 1
!
!
crypto ipsec transform-set REMOTOS esp-3des esp-sha-hmac
!
crypto dynamic-map ACCESOS_REMOTOS 1
set transform-set REMOTOS
reverse-route
!
!
crypto map REMOTOS client authentication list Remotos
crypto map REMOTOS isakmp authorization list Remotos
crypto map REMOTOS client configuration address respond
crypto map REMOTOS 1 ipsec-isakmp dynamic ACCESOS_REMOTOS
!
archive
log config
  hidekeys
!
!
!
!
!
!
interface GigabitEthernet0/0
description Conexion con Firewall-Outside
ip address 192.168.101.1 255.255.255.252
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
!
interface GigabitEthernet0/1
description $ES_LAN$
no ip address
shutdown
duplex auto
speed auto
!
interface ATM0/0/0
description CONEXION CON INTERNET
ip address x.x.x.x 255.255.255.192
ip nbar protocol-discovery
ip nat outside
ip virtual-reassembly
no atm ilmi-keepalive
dsl operating-mode auto
crypto map REMOTOS
pvc telefonica 8/32
  protocol ip x.x.x.x
  encapsulation aal5snap
!
!
interface GigabitEthernet0/1/0
  no ip address
shutdown
negotiation auto
!
interface GigabitEthernet0/1/0.1
!
deleted
ip local pool Serikat 10.14.81.233
deleted
!
!
deleted
ip nat inside source route-map NAT interface ATM0/0/0 overload
!
deleted
deleted
access-list 103 deny   ip 10.14.81.0 0.0.0.255 host 10.14.81.233
deleted
access-list 103 permit ip 10.14.81.0 0.0.0.255 any
deleted
access-list 121 permit ip host 10.14.81.172 host 10.14.81.233
delted
!        
route-map NAT permit 1
match ip address 103
!        
!        
!        
!        
deleted

cisco2821#

[fmartos]

Jennifer, Nagaraja, thanks a lot for your help. After write the commands proposes by Jennifer, the connections from vpn client to internal IP works. I am really very happy.

Thanks, thanks a lot

You are invited to have coffe if you come to Spain sometime: my email is fmartos@cepc.es

[Jennifer Halim]

Great to hear it's working, Francisco. Thanks for the invite..