Allow access to device and no internet

[Matt Roberts]

Tried to configure access to device through firewall by giving it a static NAT and ACL rule but no luck. The device also doesn't have internet access not sure what I have configured wrong. Please help

Saved
:
ASA Version 9.1(2)
!
hostname
enable password
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd
names
!
interface Ethernet0/0
 switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
 nameif inside
 security-level 100
 ip address internal 192.168.12.1 255.255.255.0
!
interface Vlan2
 nameif outside
 security-level 0
 ip address public IP 255.255.255.240
!
boot system disk0:/asa912-k8.bin
ftp mode passive
same-security-traffic permit intra-interface
object network obj_any
 subnet 0.0.0.0 0.0.0.0
object network device
 host 192.168.12.127
access-list outside_access_in extended permit ip any any log debugging
pager lines 24
logging enable
logging asdm debugging
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-713.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
!
object network device
 nat (inside,outside) static public IP
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 gatway IP 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable

no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
management-access inside

dhcpd dns 8.8.8.8
dhcpd auto_config outside
!
dhcpd address 192.168.12.10-192.168.12.41 inside
dhcpd enable inside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept

!
class-map inspection_default
 match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
 parameters
  message-length maximum 512
policy-map global_policy
 class inspection_default
  inspect dns preset_dns_map
  inspect ftp
  inspect h323 h225
  inspect h323 ras
  inspect rsh
  inspect rtsp
  inspect esmtp
  inspect sqlnet
  inspect skinny  
  inspect sunrpc
  inspect xdmcp
  inspect sip  
  inspect netbios
  inspect tftp
  inspect ip-options
!
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
 profile CiscoTAC-1
  no active
  destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
  destination address email callhome@cisco.com
  destination transport-method http
  subscribe-to-alert-group diagnostic
  subscribe-to-alert-group environment
  subscribe-to-alert-group inventory periodic monthly
  subscribe-to-alert-group configuration periodic monthly
  subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:7de894529d85e9c3ecc866af3a39f9bc
: end
asdm image disk0:/asdm-713.bin
no asdm history enable

[m.kafka]

Hi Matt,

first steps should always be packet tracer, sh xlat, show conn, show access-list etc...

can you ping 8.8.8.8 from the ASA-console?

do you have match counters on the ACL? (show access-list)

do you have active connections in the conn table when you try to reach a destination on the internet? (show conn)

does the xlate look somehow reasonable? (show xlate)

try the packet tracer, it's quite intuitive on the GUI. what's the output? (tools -> packet tracer)

as long as the ASA is non-productive debugging with packet capture: http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/118097-configure-asa-00.html

rgds, MiKa