09-04-2010 07:26 PM - edited 03-11-2019 11:35 AM
Can anyone tell me how to resolve this error message?
%Error opening tftp://192.168.1.107/asdm-602.bin (No such device)
I get this while I am rying to copy the ISO image to the ASA. I messed up and deleted everything and now trying to set it back up. Please help.
Thanks,
Jonathan
Solved! Go to Solution.
09-05-2010 10:16 AM
Hello,
Yes. Copy the file same way as the OS. Then, you need to set the ASDM image
name:
ASA# config t
ASA(config)# asdm image disk0:/asdm-602.bin
Hope this helps.
Regards,
NT
09-04-2010 07:55 PM
What does the output of "show flash" show?
If it shows "%Error show flash: (No such device)", then you would need to RMA the ASA.
09-04-2010 11:29 PM
Hi Jonathan,
Could you paste the exact command you are trying to execute and the current configuration on the firewall? Are you able to ping the tftp server 192.168.1.107, from the ASA?
Thanks and Regards,
Prapanch
09-05-2010 04:09 AM
copy tftp disk0
Address of name of remote host []? 10.10.26.2
Source filename []? asa823-k8.bin
Destination filename [disk0]? disk0
Accessing tftp://10.10.26.2/asa832-k8.bin...
%Error opening tftp://10.10.26.2/asa832-k8.bin (No Such Device)
Unable to ping
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.26.1, timeout is 2 seconds
No route to host 10.10.26.1
I have tried to configure the the IP address and I get an error message saying:
ERROR: This command can only be configured on VLAN Interface
If is do a show ip, I get nothing.
Any ideas?
09-05-2010 07:14 AM
Hey Jonathan,
The ASA 5505 has all switchports (or L2 ports) and hence we can not assign IP addresses to them directly. We will need to configure VLANs with IP addresses and assign the physical ports to the appropriate VLANs (just as we configure any Layer 2 switch).
Below is the link to configure interface on ASA 5505:
http://www.cisco.com/en/US/docs/security/asa/asa80/configuration/guide/int5505.html
So if you have your Ethernet0 interface directly connected to the TFTP server (10.10.26.2), the configurtion will look something like before:
interface vlan1
ip address 10.10.26.2
nameif inside
no shut
interface eth0
switchport access vlan1
no shut
Let me know if this helps!!
Thanks and Regards,
Prapanch
09-05-2010 07:47 AM
Thanks, that got me an IP address...but I am still unable to copy the file from the tftp server to flash or disk0. Have I done something completely wrong? Should I connect via a crossover cable? Right now I have the asa hooked up to my belkin wireless router so my laptop with the tftp server software can transfer the files needed. I will say I am completely new to cisco products so please dumb down if at all possible what I should do. I can't thank you enough for helping me out.
09-05-2010 08:01 AM
Hello,
Can you ping the ASA from your TFTP server? Does the TFTP server has any
Firewall configured on it (Windows firewall, AntiVirus firewall, or any
other custom firewall)? If yes, please turn them off and try again. Here are
the steps:
Step 1: Verify connectivity
From the command prompt of the TFTP server, ping the ASA's IP. Similarly,
from the ASA, ping TFTP Server's IP. Make sure that all ping requests get
answered.
Step 2: Copy the file
On the firewall, issue the following command: "copy tftp: flash:" It will
ask for the TFTP server IP address, and then the file name. Input those
details. At that point, the file transfer should start happening. (Make sure
that the TFTP server program is running on the TFTP server device).
Hope this helps.
Regards,
NT
09-05-2010 08:06 AM
stupid question....how do I know what the ip address if of the ASA? I have looked at the belkin router to see if I can see what it is via the dhcp client list, but it does not show up. I think they are "talk" because I can load the image from the rommon prompt but no luck copying to disk0.
thanks
09-05-2010 08:08 AM
Hello,
On the ASA, at the "ASA#" prompt, issue the command "show IP". It will tell
you the IP address of the interfaces.
Regards,
NT
09-05-2010 08:25 AM
Alrigh, got the ip address, it is only a vlan address. i still can not ping anything. Any idea?
09-05-2010 08:30 AM
Hello,
What is the IP address you have on the ASA? What is the IP of the tftp
server?
Regards,
NT
09-05-2010 08:53 AM
TFTP server is 10.10.26.6
Do I give the ASA an IP address or will it grab on from the Belkin Router. I just did an erase to clear everything out...starting from a blank ASA
09-05-2010 08:57 AM
Hello,
You give an IP address in the range of 10.10.26.x.
Regards,
NT
09-05-2010 09:02 AM
ASA IP 10.10.26.20
Loading TFTP image to ASA now via ROMMON command
What should be the next step?
09-05-2010 09:26 AM
Hello,
Once the ASA boots up, give an IP to the VLAN interface:
ASA# configure terminal
ASA(config)# interface vlan 1
ASA(config-if)# nameif inside
ASA(config-if)# security-level 100
ASA(config-if)# ip address 10.10.26.20 255.255.255.0
ASA(config-if)# exit
ASA(config)# interface Ethernet 1
ASA(config-if)# Switchport access vlan 1
ASA(config-if)# exit
Check the connectivity between the ASA and TFTP Server:
ASA(config)# ping 10.10.26.6
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.20.6, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
Once the connectivity is checked, now you should be able to copy the image:
ASA(config)# copy tftp flash:
Address or name of remote host []? 10.10.20.6
Source filename []? asa823-k8.bin
Hope this helps.
Regards,
NT
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide