Sorry, I was away so could not respond.
Problem as stated is ap does not allow enable. So I tried reset. It probably identified an issue
bad mzip file, uncompressed to wrong length , (0x1cf119d != 0x1cf1660)
Error loading "flash:/ap1g1-k9w7-mx.153-3.JC1/ap1g1-k9w7-mx.153-3.JC1"
But I don't know where I can get the correct file and how to load it to wlan addon board from 5506W host.
Thx.
ciscoasa(config)# hw-module module wlan recover configuration
WARNING: Entering this command will suspend the ASA console as long as the module recovery process is in progress.
Do you want to proceed [confirm]?
Configuration recovery is now complete.
You can now session into the module console to issue any further commands.
ciscoasa(config)# session wlan console
Opening console session with module wlan.
Connected to module wlan. Escape character sequence is 'CTRL-^X'.
enable
Unknown cmd: enable
ap: ?
? -- Present list of available commands
arp -- Show arp table or arp-resolve an address
boot -- Load and boot an executable image
cat -- Concatenate (type) file(s)
clear_ether -- clear ethernet port statistics
copy -- Copy a file
delete -- Delete file(s)
dir -- List files in directories
dump_regs -- dump reset registers
etest -- test emac driver code
ether_init -- initialize ethernet port
flash_init -- Initialize flash filesystem(s)
format -- Format a filesystem
fsck -- Check filesystem consistency
help -- Present list of available commands
init_pci -- initialize pci bridge
led_test -- cycle LED patterns
load_helper -- Load and initialize a helper image
memory -- Present memory heap utilization information
mkdir -- Create dir(s)
more -- Concatenate (display) file(s)
phy_dump -- dump phy registers
phy_read -- read phy register
phy_write -- write phy register
rename -- Rename a file
reset -- Reset the system
rmdir -- Delete empty dir(s)
set -- Set or display environment variables
set_baud -- set baud rates
set_sleep -- Pause (sleep) for a specified number of seconds
show_ether -- show ethernet port statistics
show_pci -- show pci setting
switch status -- report push button switch status
tar -- extract or listing a tar file
test_ddr -- test ddr
test_ddr_rd -- test ddr_rd
test_ddr_wr -- test ddr_wr
tftp_init -- Initialize tftp file system
type -- Concatenate (type) file(s)
unset -- Unset one or more environment variables
version -- Display boot loader version
warm_pci -- warm pci rst
ap: reset
Are you sure you want to reset the system (y/n)?y
System resetting...
U-Boot 1.1.4.v5.3--LSDK-9.4.0_RC32.2 (Oct 14 2014 - 16:40:54)
DRAM: 128 MB
CPU: 560 MHz
Top of RAM usable for U-Boot at: 88000000
Reserving 283k for U-Boot at: 87fb8000
Reserving 144k for malloc() at: 87f94000
Reserving 44 Bytes for Board Info at: 87f93fd4
Reserving 36 Bytes for Global Data at: 87f93fb0
Reserving 128k for boot params() at: 87f73fb0
Stack Pointer at: 87f73f98
Now running in RAM - U-Boot at: 87fb8000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x14
flash size 1MB, sector count = 64
Flash: 1 MB
Fetching MAC Address from 0x87fe3868
eth0: f0:78:16:3d:ef:f6
Ethernet link up - 1000Mbps Full
eth0
Atheros on-chip NAND FLash Controller Driver, Version 0.1 (c) 2010 Atheros Communications, Ltd.
Ath Nand ID[87ff117c]: 2c:f1:80:95:02
ONFI MICRON MT29F1G08ABADAWP
Micron NAND 128MiB 3,3V 8-bit [128MB]
====== NAND Parameters ======
sc = 0x87ff1158 bbt = 0x87f98360 bbt_size = 0x100 nf_ctrl = 0x344
page = 0x800 block = 0x20000 oob = 0x40
size = 128MB
Setting 0xb8116290 to 0x2a542d0f
Test Size=0x8000000, Start!!
RAM test complete!
PTD Init
MAC address check ok!
boot method:3
Hit "ESC" to stop autoboot: 0
Uncompressed size: 323407 = 0x4EF4F
Loading .text @ 0x84000000 (203840 bytes)
Loading .rodata @ 0x84031c40 (41024 bytes)
Loading .data @ 0x8403bc80 (2752 bytes)
Loading .data.rel.local @ 0x8403c740 (1020 bytes)
Loading .data.rel.ro.local @ 0x8403cb3c (96 bytes)
Loading .data.rel @ 0x8403cb9c (88 bytes)
Loading .data.rel.ro @ 0x8403cbf4 (996 bytes)
Clearing .bss @ 0x8403cfe0 (161080 bytes)
Clearing .scommon @ 0x84064518 (60 bytes)
## Starting application at 0x84000000 ...
IOS Secondary Bootloader - Starting system.HW Test Status(0)
Ath Nand ID: 95:80:f1:2c:00
Using driver version 1 for media type 2
Valid buffers 212
total212 212
success found all blocks
start end 79 86
found in range
high low end 2762 2546 86
Xmodem file system is available.
mifs[0]: 214 files, 7 directories
mifs[0]: Total bytes : 131334144
mifs[0]: Bytes used : 13215744
mifs[0]: Bytes available : 118118400
mifs[0]: mifs fsck took 0 seconds.
Base Ethernet MAC address: f0:78:16:3d:ef:f6
Setup MAC....
Ethernet speed is 1000 Mb - FULL duplex
Setting Drop CRC Errors, Pause Frames and Length Error frames
: cfg1 0xf cfg2 0x7215
Loading "flash:/ap1g1-k9w7-mx.153-3.JC1/ap1g1-k9w7-mx.153-3.JC1"...####################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################
bad mzip file, uncompressed to wrong length , (0x1cf119d != 0x1cf1660)
Error loading "flash:/ap1g1-k9w7-mx.153-3.JC1/ap1g1-k9w7-mx.153-3.JC1"
Interrupt within 5 seconds to abort boot process.
Boot process failed...
The system is unable to boot automatically. The BOOT
environment variable needs to be set to a bootable
image.
ap1g1 Boot Loader (ap1g1-BOOT-M) RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Mon 04-May-15 15:21 by prod_rel_team
ap:
