01-29-2013 03:43 PM - edited 03-11-2019 05:54 PM
I have a ASA 5510 with Security Plus License and when I looked at the devices a few days ago I had 2 contexts, however after configuring the Mgm port as a regular port the contexts show 0, why? I can not find any post on the internet where this issue has happen: here is the output from show ver:
Cisco Adaptive Security Appliance Software Version 7.0(8)
Compiled on Sat 31-May-08 23:48 by builders
System image file is "disk0:/asa708-k8.bin"
Config file at boot was "startup-config"
SHIELDASA01 up 21 hours 16 mins
Hardware: ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
Boot microcode : CNlite-MC-Boot-Cisco-1.2
SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.05
0: Ext: Ethernet0/0 : address is 0021.a025.2d3c, irq 9
1: Ext: Ethernet0/1 : address is 0021.a025.2d3d, irq 9
2: Ext: Ethernet0/2 : address is 0021.a025.2d3e, irq 9
3: Ext: Ethernet0/3 : address is 0021.a025.2d3f, irq 9
4: Ext: Management0/0 : address is 0021.a025.2d3b, irq 11
5: Int: Not used : irq 11
6: Int: Not used : irq 5
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 25
Inside Hosts : Unlimited
Failover : Active/Standby
VPN-DES : Enabled
VPN-3DES-AES : Enabled
Security Contexts : 0
GTP/GPRS : Disabled
VPN Peers : 150
This platform has an ASA 5510 Security Plus license.
I am not showing the serial number and licese keys for obivious reasons. Any help? Thanks in advance.
Solved! Go to Solution.
01-30-2013 01:30 AM
You might want to try upgrading your IOS on the ASA, see if this helps, can you verify the firewall mode(single or multiple) you are currently on? is your asa transparant or routed?
01-30-2013 01:30 AM
You might want to try upgrading your IOS on the ASA, see if this helps, can you verify the firewall mode(single or multiple) you are currently on? is your asa transparant or routed?
01-30-2013 06:15 PM
Upgrading the ASA from asa708-k8.bin to asa805-k8 worked! Once I TFTP a newer version (not the latest) but it worked: Here is the show ver result: (some parts omitted)
Cisco Adaptive Security Appliance Software Version 8.0(5)
Compiled on Mon 02-Nov-09 21:22 by builders
System image file is "disk0:/asa805-k8.bin"
Config file at boot was "startup-config"
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 100
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Enabled
Security Contexts : 2
GTP/GPRS : Disabled
VPN Peers : 250
WebVPN Peers : 2
AnyConnect for Mobile : Disabled
AnyConnect for Linksys phone : Disabled
Advanced Endpoint Assessment : Disabled
UC Proxy Sessions : 2
This platform has an ASA 5510 Security Plus license.
Thanks Rudy great job!
01-31-2013 01:46 AM
You're welcome, I believe you are also aware that the amount of peers and vlans also changed by upgrading the software, now you have the number that you should have by having security plus license on asa5510, which is good.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide