ASA 8.4 IPSec-L2L VPN 1-Way communication

[RobertJLake]

Hello,

I am currently trying to configure a Site-to-Site VPN tunnel and have seemed to stumbled into a problem. I appear to only be able to communicate in 1 direction, my 10.1.1.x clients are able to ping clients on the 192.168.135.x network; however, the 192.168.135.x clients are not able to ping clients on the 10.1.1.x network.

Topology

10.1.1.x/24 inside(ASA1)outside ===VPN===outside(ASA2)inside 192.168.135.x/24

I'm not sure which all outputs will be valuable to you to assist so let me know if I'm missing anything.

ASA1

ciscoasa(config)# sh run nat
nat (inside,outside) source static local-nets local-nets destination static vpn-nets vpn-nets no-proxy-arp route-lookup
!
object network obj_any
 nat (inside,outside) dynamic interface

ciscoasa# sh run route
route outside 0.0.0.0 0.0.0.0 X.X.X.X 1

crypto ipsec ikev1 transform-set ESP-AES-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set triplesha esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set aes256sha esp-aes-256 esp-sha-hmac
crypto map vpnmap 120 match address outbound
crypto map vpnmap 120 set peer X.X.X.X
crypto map vpnmap 120 set ikev1 transform-set triplesha
crypto map vpnmap interface outside
crypto ikev1 enable outside
crypto ikev1 policy 120
 authentication pre-share
 encryption 3des
 hash sha
 group 2
 lifetime 86400

ASA2

PT-Hold-ASA5505# sh run nat
nat (inside,outside) source static local-nets local-nets destination static vpn-nets vpn-nets no-proxy-arp route-lookup
!
object network obj_any
 nat (inside,outside) dynamic interface

PT-Hold-ASA5505# sh run route
route outside 0.0.0.0 0.0.0.0 X.X.X.X 1

crypto map vpnmap 120 match address robASA
crypto map vpnmap 120 set peer X.X.X.X
crypto map vpnmap 120 set ikev1 transform-set aes256sha triplesha
crypto map vpnmap 255 ipsec-isakmp dynamic dynmap
crypto map vpnmap interface outside

crypto ikev1 policy 120
 authentication pre-share
 encryption 3des
 hash sha
 group 2
 lifetime 86400

Thank you for any help you have to offer, I'm not very familiar with ASA's

[ROHIT SHARMA]

Hello Robert,

Is it possible for you to paste complete config here?

This problem is generally due to NAT or routing issues.

[RobertJLake]

Sure,

Here is ASA1
: Saved
:
ASA Version 8.4(6)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Ethernet0/0
 switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
 nameif inside
 security-level 100
 ip address 10.1.1.1 255.255.255.0
!
interface Vlan2
 nameif outside
 security-level 0
 ip address 173.X.X.X 255.255.255.0
!
boot system disk0:/asa846-k8.bin
boot system disk0:/asa847-28-k8.bin
ftp mode passive
object network obj_any
 subnet 0.0.0.0 0.0.0.0
object-group network private-nets
 network-object 10.0.0.0 255.0.0.0
 network-object 172.16.0.0 255.240.0.0
 network-object 192.168.0.0 255.255.0.0
 network-object 127.0.0.0 255.255.255.0
 network-object host 0.0.0.0
object-group network local-nets
 network-object 10.1.1.0 255.255.255.0
object-group network hf-nets
 network-object 192.168.135.0 255.255.255.0
object-group network vpn-nets
 group-object hf-nets
object-group service blocked-udp udp
 port-object range 135 139
 port-object eq snmp
object-group service blocked-tcp tcp
 port-object range 135 netbios-ssn
 port-object eq ldap
 port-object eq 445
 port-object eq 593
access-list outbound extended permit ip object-group local-nets object-group hf-nets
access-list outboundtraffic extended permit ip object-group local-nets object-group vpn-nets
access-list outboundtraffic extended deny udp any any object-group blocked-udp
access-list outboundtraffic extended deny tcp any any object-group blocked-tcp
access-list outboundtraffic extended permit ip object-group local-nets any
access-list holdingford extended permit ip object-group local-nets object-group hf-nets
access-list inboundtraffic extended deny ip object-group private-nets any
access-list inboundtraffic extended permit icmp any any echo
access-list inboundtraffic extended permit icmp any any echo-reply
access-list inboundtraffic extended permit icmp any any time-exceeded
access-list bypassnat extended permit ip object-group local-nets object-group vpn-nets
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-645.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source static local-nets local-nets destination static vpn-nets vpn-nets no-proxy-arp route-lookup
!
object network obj_any
 nat (inside,outside) dynamic interface
route outside 0.0.0.0 0.0.0.0 173.X.X.X 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 10.1.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sysopt connection tcpmss 1180
crypto ipsec ikev1 transform-set ESP-AES-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set triplesha esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set aes256sha esp-aes-256 esp-sha-hmac
crypto map vpnmap 120 match address outbound
crypto map vpnmap 120 set peer 208.X.X.X
crypto map vpnmap 120 set ikev1 transform-set triplesha
crypto map vpnmap interface outside
crypto ikev1 enable outside

crypto ikev1 policy 120
 authentication pre-share
 encryption 3des
 hash sha
 group 2
 lifetime 86400
telnet timeout 5
ssh 192.168.135.0 255.255.255.0 inside
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0

dhcpd dns 173.X.X.X 173.X.X.X
!
dhcpd address 10.1.1.5-10.1.1.15 inside
dhcpd enable inside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl encryption aes128-sha1 3des-sha1 aes256-sha1
webvpn
tunnel-group 208.X.X.X type ipsec-l2l
tunnel-group 208.X.X.X ipsec-attributes
 ikev1 pre-shared-key *****
!
!
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:6d579c34db053bd2b38bcf0a40cdebc8
: end

ASA2

: Saved
:
ASA Version 8.4(6)5
!
hostname PT-Hold-ASA5505
domain-name XXXXXXXX
enable password ppn/h7gQhH2MPtdi encrypted
passwd ppn/h7gQhH2MPtdi encrypted
no names
dns-guard
!
interface Ethernet0/0
 switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
 nameif inside
 security-level 100
 ip address 192.168.135.1 255.255.255.0
!
interface Vlan2
 nameif outside
 security-level 0
 ip address 208.X.X.X 255.255.255.252
!
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
dns server-group DefaultDNS
 domain-name XXXXXXXXX
object network obj_any
 subnet 0.0.0.0 0.0.0.0
object-group network private-nets
 network-object 10.0.0.0 255.0.0.0
 network-object 172.16.0.0 255.240.0.0
 network-object 192.168.0.0 255.255.0.0
 network-object 127.0.0.0 255.255.255.0
 network-object host 0.0.0.0
object-group network local-nets
 network-object 192.168.135.0 255.255.255.0
object-group network opole-nets
 network-object 192.168.110.0 255.255.255.0
object-group network client-nets
 network-object 192.168.254.0 255.255.255.0
object-group network robASA-nets
 network-object 10.1.1.0 255.255.255.0
object-group network vpn-nets
 group-object client-nets
 group-object opole-nets
 group-object robASA-nets
object-group service blocked-udp udp
 port-object range 135 139
 port-object eq snmp
object-group service blocked-tcp tcp
 port-object range 135 netbios-ssn
 port-object eq ldap
 port-object eq 445
 port-object eq 593
access-list opole extended permit ip object-group local-nets object-group opole-nets
access-list inboundtraffic extended deny ip object-group private-nets any
access-list inboundtraffic extended permit icmp any any echo
access-list inboundtraffic extended permit icmp any any echo-reply
access-list inboundtraffic extended permit icmp any any time-exceeded
access-list outboundtraffic extended permit ip object-group local-nets object-group vpn-nets
access-list outboundtraffic extended deny udp any any object-group blocked-udp
access-list outboundtraffic extended deny tcp any any object-group blocked-tcp
access-list outboundtraffic extended permit ip object-group local-nets any
access-list clientmatch extended permit ip object-group local-nets object-group client-nets
access-list robASA extended permit ip object-group local-nets object-group robASA-nets
pager lines 24
logging enable
logging timestamp
logging buffered debugging
logging asdm informational
no logging message 305012
no logging message 305011
no logging message 715075
no logging message 715047
no logging message 715046
no logging message 302015
no logging message 302014
no logging message 302013
no logging message 304001
no logging message 715036
no logging message 713236
no logging message 609002
no logging message 609001
no logging message 302016
no logging message 302021
no logging message 302020
mtu inside 1500
mtu outside 1500
ip local pool vpnpool 192.168.254.1-192.168.254.126
ip verify reverse-path interface inside
ip verify reverse-path interface outside
icmp unreachable rate-limit 1 burst-size 1
asdm history enable
arp timeout 300
no arp permit-nonconnected
nat (inside,outside) source static local-nets local-nets destination static vpn-nets vpn-nets no-proxy-arp route-lookup
!
object network obj_any
 nat (inside,outside) dynamic interface
access-group outboundtraffic in interface inside
access-group inboundtraffic in interface outside
route outside 0.0.0.0 0.0.0.0 208.X.X.X 1
route outside 10.1.1.0 255.255.255.0 173.X.X.X 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
aaa authentication http console LOCAL
http server enable XXXXX
http X.X.X.X X.X.X.X inside
http X.X.X.X X.X.X.X outside
http X.X.X.X X.X.X.X outside
http 192.168.135.0 255.255.255.0 inside
http X.X.X.X X.X.X.X inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sysopt connection timewait
crypto ipsec ikev1 transform-set aes256sha esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set triplesha esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto dynamic-map dynmap 10 set ikev1 transform-set aes256sha
crypto map vpnmap 110 match address opole
crypto map vpnmap 110 set peer X.X.X.X
crypto map vpnmap 110 set ikev1 transform-set aes256sha triplesha
crypto map vpnmap 120 match address robASA
crypto map vpnmap 120 set peer 173.X.X.X
crypto map vpnmap 120 set ikev1 transform-set aes256sha triplesha
crypto map vpnmap 255 ipsec-isakmp dynamic dynmap
crypto map vpnmap interface outside
crypto ca trustpoint _SmartCallHome_ServerCA
 crl configure
crypto ca certificate chain _SmartCallHome_ServerCA
 certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
    308205ec 308204d4 a0030201 0202106e cc7aa5a7 032009b8 cebcf4e9 52d49130
    0d06092a 864886f7 0d010105 05003081 ca310b30 09060355 04061302 55533117
    30150603 55040a13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
    13165665 72695369 676e2054 72757374 204e6574 776f726b 313a3038 06035504
    0b133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
    20617574 686f7269 7a656420 75736520 6f6e6c79 31453043 06035504 03133c56
    65726953 69676e20 436c6173 73203320 5075626c 69632050 72696d61 72792043
    65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
    30303230 38303030 3030305a 170d3230 30323037 32333539 35395a30 81b5310b
    30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20
    496e632e 311f301d 06035504 0b131656 65726953 69676e20 54727573 74204e65
    74776f72 6b313b30 39060355 040b1332 5465726d 73206f66 20757365 20617420
    68747470 733a2f2f 7777772e 76657269 7369676e 2e636f6d 2f727061 20286329
    3130312f 302d0603 55040313 26566572 69536967 6e20436c 61737320 33205365
    63757265 20536572 76657220 4341202d 20473330 82012230 0d06092a 864886f7
    0d010101 05000382 010f0030 82010a02 82010100 b187841f c20c45f5 bcab2597
    a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
    9c688b2e 957b899b 13cae234 34c1f35b f3497b62 83488174 d188786c 0253f9bc
    7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
    15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
    63cd1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8
    18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
    4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
    81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 02030100 01a38201 df308201
    db303406 082b0601 05050701 01042830 26302406 082b0601 05050730 01861868
    7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1d130101
    ff040830 060101ff 02010030 70060355 1d200469 30673065 060b6086 480186f8
    45010717 03305630 2806082b 06010505 07020116 1c687474 70733a2f 2f777777
    2e766572 69736967 6e2e636f 6d2f6370 73302a06 082b0601 05050702 02301e1a
    1c687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
    03551d1f 042d302b 3029a027 a0258623 68747470 3a2f2f63 726c2e76 65726973
    69676e2e 636f6d2f 70636133 2d67352e 63726c30 0e060355 1d0f0101 ff040403
    02010630 6d06082b 06010505 07010c04 61305fa1 5da05b30 59305730 55160969
    6d616765 2f676966 3021301f 30070605 2b0e0302 1a04148f e5d31a86 ac8d8e6b
    c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973
    69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30
    1b311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301d0603
    551d0e04 1604140d 445c1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355
    1d230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300d0609
    2a864886 f70d0101 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80
    4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
    b2227055 d9203340 3307c265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
    6decd018 7d494aca 99c71928 a2bed877 24f78526 866d8705 404167d1 273aeddc
    481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
    b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
    5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
    6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
    6c2527b9 deb78458 c61f381e a4c4cb66
  quit
crypto isakmp identity address
crypto ikev1 enable outside
crypto ikev1 policy 10
 authentication pre-share
 encryption aes-256
 hash sha
 group 2
 lifetime 43200
crypto ikev1 policy 120
 authentication pre-share
 encryption 3des
 hash sha
 group 2
 lifetime 86400
crypto ikev1 policy 666
 authentication pre-share
 encryption aes
 hash md5
 group 2
 lifetime 86400
telnet 192.168.135.0 255.255.255.0 inside
telnet timeout 30
ssh X.X.X.X X.X.X.X inside
ssh 192.168.135.0 255.255.255.0 inside
ssh X.X.X.X X.X.X.X inside
ssh 10.1.1.0 255.255.255.0 inside
ssh X.X.X.X X.X.X.X outside
ssh X.X.X.X X.X.X.X outside
ssh timeout 60
ssh key-exchange group dh-group1-sha1
console timeout 30
management-access inside

dhcpd auto_config outside
!
dhcpd address 192.168.135.101-192.168.135.200 inside
dhcpd dns 192.168.110.4 24.56.130.2 interface inside
dhcpd domain XXXXXXXl interface inside
dhcpd enable inside
!
threat-detection basic-threat
threat-detection statistics
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
ntp server 192.168.110.4 source inside
webvpn
group-policy DfltGrpPolicy attributes
 vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-clientless
group-policy mgmtvpn internal
group-policy mgmtvpn attributes
 split-tunnel-policy tunnelspecified
 split-tunnel-network-list value clientmatch
username ptt_it password zZLj1eRw6II4.leT encrypted privilege 15
username mtech password //lVvNVoVoZ8qRzR encrypted privilege 15
tunnel-group mgmtvpn type remote-access
tunnel-group mgmtvpn general-attributes
 address-pool vpnpool
 default-group-policy mgmtvpn
tunnel-group mgmtvpn ipsec-attributes
 ikev1 pre-shared-key *****
tunnel-group X.X.X.X type ipsec-l2l
tunnel-group X.X.X.X ipsec-attributes
 ikev1 pre-shared-key *****
tunnel-group 173.X.X.X type ipsec-l2l
tunnel-group 173.X.X.X ipsec-attributes
 ikev1 pre-shared-key *****
!
class-map inspection_default
 match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
 parameters
  message-length maximum client auto
  message-length maximum 4096
policy-map global_policy
 class inspection_default
  inspect dns preset_dns_map
  inspect ftp
  inspect h323 h225
  inspect h323 ras
  inspect rsh
  inspect rtsp
  inspect esmtp
  inspect sqlnet
  inspect skinny
  inspect sunrpc
  inspect xdmcp
  inspect sip
  inspect netbios
  inspect tftp
  inspect ip-options
 class class-default
  user-statistics accounting
!
service-policy global_policy global
prompt hostname context
call-home reporting anonymous
hpm topN enable
Cryptochecksum:0690e432b9864e1fb23dda44cf08e7cd
: end

Also just an FYI the second ASA is in production, we are trying to diagnose speed issues at a different facility so we created ASA 1 to bypass a suspect ASA. So I've been trying to copy the general configurations and that is why you see two peers under the crypto maps.

If you can think of anything please let me know, I greatly appreciate any help!

[ROHIT SHARMA]

I'll try to simulate it.

Just curious, why you have this route in ASA2 ?

route outside 10.1.1.0 255.255.255.0 173.X.X.X 1

[RobertJLake]

Thank you so much for all the help, I truly do appreciate it.

That route was something that I tried to use in a last ditch effort to try making things work before coming here and it did not make any difference. I guess I don't fully understand the the flow of logic for route creation/syntax.

[ROHIT SHARMA]

I just simulated your config in GNS3. It works fine both ways!

Now the only way to troubleshoot it is to debug.

Can you enable debug and logging ?

If you have a very big network then use condition debugging.

Initiate traffic from subnet 192.168.135.0 to 10.1.1.0 and see debug output on ASA2.

[RobertJLake]

Well it is a relief that it works in a way, now I just need to figure out how to find the problem. I'm not familiar with debugging at all, would you be able to assist me through the steps? How do I enable debugging and logging? Which ASA would I run this on(I imagine ASA2)? 

We have a pretty large network but  the connection from ASA2 to ASA1 is a much smaller picture which is why I chose that to work on. Any guidance would be great!

[ROHIT SHARMA]

1. clear crypto ikev1 sa <peer_address> on both ASA.

2. clear crypto ipsec sa peer <peer address> on both ASA

3. initiate a ping from subnet 192.168.135.0/24 to 10.1.1.0/24.

4. show crypto isakmp sa   on ASA2 and paste output here.

Also, i am attaching the config i used to simulate this. Please compare with yours and see if there is any difference. I have assumed peer address randomly.

[RobertJLake]

What does the clear crypto ipsec sa peer <peer address> command do, I'm not familiar with SA. I will try this and post back tomorrow when I'm in the office since I need physical access to ASA1 for me to make any changes. I looked through the configuration and it seems to me like everything is the same, I'm just hoping I'm not overlooking some small detail that is throwing everything off.

[ROHIT SHARMA]

its fine if you can do it on ASA2 only.

[RobertJLake]

Here are the results from the commands above when I run it only on ASA2

PT-Hold-ASA5505# sh crypto isakmp sa

IKEv1 SAs:

   Active SA: 1
    Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1

1   IKE Peer: x.x.x.x
    Type    : L2L             Role    : responder
    Rekey   : no              State   : MM_ACTIVE

There are no IKEv2 SAs
PT-Hold-ASA5505#

That peer is the pre-existing connection that is currently working in production.

[RobertJLake]

I spoke too soon, after I let it sit for a few minutes it now does show the two connections; here is the output:

IKEv1 SAs:

   Active SA: 2
    Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 2

1   IKE Peer: X.X.X.X
    Type    : L2L             Role    : responder
    Rekey   : no              State   : MM_ACTIVE
2   IKE Peer: 173.X.X.X
    Type    : L2L             Role    : responder
    Rekey   : no              State   : MM_ACTIVE
PT-Hold-ASA5505#

[ROHIT SHARMA]

Initiate a ping again and

show crypto ipsec sa

[RobertJLake]

Here is the result of those string of commands:

PT-Hold-ASA5505# ping 10.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
PT-Hold-ASA5505# clear crypto ikev1 sa 173.X.X.X
PT-Hold-ASA5505# sh crypto isakmp sa

IKEv1 SAs:

   Active SA: 2
    Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 2

1   IKE Peer: X.X.X.X
    Type    : L2L             Role    : responder
    Rekey   : no              State   : MM_ACTIVE
2   IKE Peer: 173.X.X.X
    Type    : L2L             Role    : responder
    Rekey   : no              State   : MM_ACTIVE

There are no IKEv2 SAs
PT-Hold-ASA5505# ping 10.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
PT-Hold-ASA5505#

One thing I did notice is if I ping the outside interface of ASA1 the ping is a successes. If I try to ping the inside interface of ASA1 or anything on that internal network it fails.

[ROHIT SHARMA]

Can you try to ping from any other device than ASA2?

I can see that you are pinging from ASA2 itself.

if you have another device behind ASA2 in subnet 192.168.135.0/24, initiate a ping from that device to an IP in internal network behind ASA1.