ASA Failover Cluster: SNMP configuration was not replicated completely

[swscco001]

Hello everybody,

we had to replace the standby-node of a ASA Failover Cluster (9.14(3)18)) because a HW defect.

After cluster re-establishment our monitoring complained because several SNMP values
could not be requested. On the primary node all is ok.

I checked the failover status:

ENAM-ASA01/pri/act# sh fa
Failover On
Failover unit Primary
Failover LAN Interface: HEARTBEAT Ethernet1/16 (up)
Reconnect timeout 0:00:00
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 1 of 1293 maximum
MAC Address Move Notification Interval not set
Cipher in use: 3DES/AES
Version: Ours 9.14(3)18, Mate 9.14(3)18
Serial Number: Ours JAD2444020W, Mate JAD23130VMN
Last Failover at: 10:00:37 CET Dec 9 2023
        This host: Primary - Active
                Active time: 618451 (sec)
                slot 0: FPR-2130 hw/sw rev (1.4/9.14(3)18) status (Up Sys)
                  Interface Transfer (10.9.0.10): Normal (Not-Monitored)
                  Interface outside (185.247.62.10): Normal (Monitored)
                  Interface management (10.31.131.155): Normal (Not-Monitored)
        Other host: Secondary - Standby Ready
                Active time: 0 (sec)
                slot 0: FPR-2130 hw/sw rev (1.4/9.14(3)18) status (Up Sys)
                  Interface Transfer (10.9.0.11): Normal (Not-Monitored)
                  Interface outside (185.247.62.11): Normal (Monitored)
                  Interface management (10.31.131.153): Normal (Not-Monitored)

Then I compared the SNMP configuration of both nodes:

Active:

ENAM-ASA01/pri/act# sh run | in snmp
snmp-server group nocasa4check v3 priv
snmp-server user nocuser nocasa4check v3 engineID <engineID deleted> encrypted auth sha <key deleted>
snmp-server host Transfer 10.9.0.15 version 3 nocuser
no snmp-server location
no snmp-server contact
snmp-server community *****
no snmp-server enable oid mempool
class-map class_snmp
 class class_snmp
  inspect snmp

------------------------------------------------------------------------

Standby:

ENAM-ASA01/sec/stby# sh run | in snmp
snmp-server group nocasa4check v3 priv
no snmp-server location
no snmp-server contact
snmp-server community *****
no snmp-server enable oid mempool
class-map class_snmp
 class class_snmp
  inspect snmp

Even if I enter 'wr mem' on the active node the SNMP configuration was not
replicated to the standby.

All other configuration was replicated.

How can I solve the issue?

Thanks a lot for every hint!


Bye
R.

[marce1000]

              - FYI : https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvy60100

 M.  

[tvotna]

This is expected behavior and the mentioned bug is not relevant for you.

Before 9.14 SNMP user information was hashed by the local SNMP engine-id in the configuration. Active and standby ASA exchanged engine-id over failover link and put two instances of the "snmp-server user" command into configuration: each hashed by the corresponding engine-id.

In 9.14 and above behavior was changed again and documented by the CSCvx18878. SNMP engine-id is no longer synchronized over failover link and each unit uses its own local engine-id to hash "snmp-server user". There is only one copy of the "snmp-server user" command in the config.

When the ASA is replaced, the new ASA has new SNMP engine-id and hence cannot accept "snmp-server user" from its peer during config sync, because hashing is a one-way function. Hence, "snmp-server user" is rejected on the new standby unit. You need to re-enter "snmp-server user" and "snmp-server host" manually on the active unit specifying passwords in clear text and then do "write mem". The commands will be synced in clear to standby, local engine-ID applied and resulting configuration saved.

[swscco001]

Hi tvotna,

thanks for your fast reply!

Unfortunately the manual re-enter of teh commands on the active unit did not solve the issue:

ENAM-ASA01/pri/act(config)# snmp-server user nocuser nocasa4check v3 engineID <engine-ID> encrypted auth sha <key deleted> priv aes 128 <key deleted>
WARNING: This command cannot be replicated because it contains localized keys.
ENAM-ASA01/pri/act(config)# snmp-server host Transfer 10.9.0.15 version 3 nocuser
ENAM-ASA01/pri/act(config)# wr mem
Building configuration...

Is there any other option I could try?

Thanks a lot!



Bye
R.

[tvotna · Accepted solution]

You need to enter passwords on the active unit in this command in clear text and don't specify engine-id. Refer to command reference for exact syntax.

[swscco001]

Hi tvotna,

I misunderstood your first reply.

After entering the 'snmp-ser user' command without engine ID and clear-text password the monitoring can  request the data again.

Thanks a lot!


Bye
R.

[swscco001]

Hi cora9881,

thanks for your reply but this is not an active/active cluster but a normal active/standby.

Thanks a lot!


Bye
R.