Resolved! FDM DHCP Relay
HelloWe have Cisco 1140 with FDM Management, version is 7.2.5. How do I need to configure DHCP Relay? Because I did all configuration, but int not working
Forum Posts
Hello Experts, I have a Cisco FMC with managed Device AMP 8130 Appliance with on-premises Threat Grid and Private Cloud. I got issues about the Integration part of the FMC with TG and FMC with Private Cloud and also having trouble with TG to Privat...
Hi, Does anyone know if we need something special on our CCO account in order to use the Secure Firewall Migration Tool? I have installed it, and as soon as I run it, it opens a browser and asks me to authenticate. Afterwards, I got a message saying...
Hello, I successfully set up/configured my first ASA device. I just purchased as second 5506 and am wondering about how compatible or incompatible the bkup configuration files I’ve saved from the first device are gonna be with the second ASA. It ment...
(FP)Firepower 1000 has routed sub-interfaces as shown in diagram. HostA is able to ping HostB, and vice-versa. FP Vlan20 responds to ping request from HostA. FP Vlan30 responds to ping request from HostB. All works with the following exception, FP Vl...
Resolved! ASA 5506 SSP Version?
Hello,With the older ASA 5505, 5510, 5520, etc. series devices, you could add an SSP module that would give you IDS/IPS functionality. This functionality showed up in the ASDM GUI as an additional tab.The newer ASA 5506-X doesn't have a slot for a m...
How to prioritise local firewall rules when global rules are also configured in Cisco ASA firewalls managed in CSMA way for local rules to get checked first when global rules are also configured in Cisco ASA firewalls managed in CSMWith rule inherita...
Hi All,I have one customer and want to have a tech refresh migration to the hardware with some modification to the current design.Current devices:Two 2600 FMC in HA with version 7.2.5Four standalone FTD 4100 version 7.2.5New hardwareTwo 4600 FMC in H...
I have a pair of ASAs that I try to add a backup ISP. I would be creating sub interfaces on Gi0/0. Once I default the Gi0/0, the Outside configuration would be gone from the configure, can I do the sub interfaces. configure Gi0/0.10 with nameif Ou...
Hello allI'm receiving hundreds of warning messages i am getting in our syslog from our Cisco ASA 5516-x. The warning message are on below same as screenshots and dunt know how to act with these kind of massages as its huge numbers of massages coming...
Hello. My CSLU can't log on into Cisco, but I can log on other Cisco web pages using same ID. Plus, I can log on CSLU & CSSM web page well using my private Cisco ID. Only my company ID can't log on into Cisco using CSLU Program. Can you give me some ...
Hi guys, I have two 5506 boxes running 9.8.3 patch 29. I login first time with ASDM and perform whatever tasks.I left ASDM open and move to other windows (probably a browser); after couple minutes a pop up from ASDM login credetials shows up. Obvious...
If I am configuring an IKEv1 IPSEC site-to-site VPN with an FTD device running 7.4.1 managed by the FMC and it is policy based, not route based, does the system ACL applied to the device also control the traffic across the tunnel? If so, then what Zo...
I was trying to configure an EEM applet on a Cisco ASA. The applet is meant to copy the running-config to TFTP each time there's a configuration change. I use 'event syslog id 111010' to trigger the applet. Interestingly enough, the CLI command 'copy...
Hi Guys, Tried to perform the reimage of the Cisco 5525-x firepower module to 6.0.0 but failed. I've setup the ftp server(filezilla) and uploaded the boot image to disk0 parttion without any issue, however, perform system image ftp://username:passwor...
