07-09-2012 02:02 PM - edited 03-11-2019 04:28 PM
Up until recently one of my sites was able to get to a postini subnet. Then we started recieving "host unreachable" e-mails. Postini told us SMTP traffic was not getting let in. I've compared the current config to a config that was saved before the issue popped up and found really no noticeable difference.
I tried a packet tracer trace with no luck:
==============================
SiteB-Firewall# packet-tracer input outside tcp 11.2.2.36 12345 65.19.0.0 25
Phase: 1
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 2
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 0.0.0.0 0.0.0.0 outside
Phase: 3
Type: ACCESS-LIST
Subtype:
Result: DROP
Config:
Implicit Rule
Additional Information:
Result:
input-interface: outside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
============================================
Attached is a sanitized config. I'm not entirely convinced it's a firewall issue, but I need to some successful testing to prove otherwise.
07-19-2012 07:19 AM
Reconfigured NAT to use seperate public IP addresses for our mail (SMTP) and RDP, using the following commands on the existing config:
===============
no static (inside,outside) tcp interface 3389 11.22.33 3389 netmask 255.255.255.255
no static (inside,outside) tcp interface smtp access-list postini-nat
static (inside,outside) 25.107.253.4 11.22.33 netmask 255.255.255.255
static (inside,outside) 25.107.253.5 11.22.36 netmask 255.255.255.255
access-list incoming extended permit tcp any host 25.107.253.4 eq 3389
access-list incoming extended permit tcp 65.19.0.0 255.255.240.0 host 25.107.253.5 eq smtp
access-list incoming extended permit icmp any any
access-group incoming in interface outside
=================
These commands did not let the mail through. In addition, after restarting the router, now the firewall can't get to anything on the internal network and I can't remote directly into it. I have to telnet into it through the local router.
Attached is sanitized config of that router. I need to figure out why the mail isn't getting through and additionally why now the firewall can't get into the internal network.
07-19-2012 07:30 AM
Ping results:
Router to inside int of Firewall: Good
Rtr to outside int of FW: Good
Rtr to IPS address (past FW): Good
Firewall to router on int that connects the 2: Good
FW to RTR int on the internal network: Fail
FW to RTR's mpls port: Fail
FW to internal network address (it's own Site): Fail
FW to internal network address (another site): Fail
07-19-2012 10:34 AM
Tried "clear xlate", have not power cycled the ASA though.
More output:
SiteB-Firewall# sh eigrp neighbors
EIGRP-IPv4 neighbors for process 102
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 11.255.2.2 Et0/1 14 19:25:28 2 200 0 11
=-=
SiteB-Firewall# sh route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is 25.107.253.1 to network 0.0.0.0
C 25.107.253.0 255.255.255.248 is directly connected, outside
C 11.255.2.0 255.255.255.252 is directly connected, inside
S* 0.0.0.0 0.0.0.0 [1/0] via 25.107.253.1, outside
=-=
SiteB-Firewall# sh eigrp topology
EIGRP-IPv4 Topology Table for AS(102)/ID(25.107.253.3)
Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,
r - reply Status, s - sia Status
P 0.0.0.0 0.0.0.0, 1 successors, FD is 28160
via Rstatic (28160/0)
P 11.255.2.0 255.255.255.252, 1 successors, FD is 2816
via Connected, Ethernet0/1
07-19-2012 10:35 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide