08-20-2020 05:05 AM
we have a ASAv installed in a single mode.
This ASA gets reboot after every one hour with below logs,
********************************************************************************
08-20-2020 05:11 AM
is this for LAB or Live environment :
Do you have Licesne and enough resources - what is the versoin of ASAv
WARNING: ASAv platform license state is Unlicensed.
08-20-2020 05:21 AM
Hi Balaji,
Thanks for your quick reply. This ASAv is in production network.
System image file is "(hd0,1)/asa9-12-3-12-smp-k8.bin"
License mode: Smart Licensing
ASAv Platform License State: Licensed
Active entitlement: ASAv-STD-100M, enforce mode: Authorized
Licensed for maximum of 1 vCPU
Installed license is insufficient for the instance type deployed. Performance is reduced with the currently installed license.
Above is the extract from show version output.
Post reboot it shows status as licensed. Resources are also fine on HyperV.
08-20-2020 05:43 AM
I have seen in my test lab other version while i am doing some PoC, suggested to increate RAM, see any Logging enabled which causing to crash.
4GB suggested or if you have more raise to 8GB and try.
check the requirment as below : (never tried hyper-v (VMWARE works fine with 4GB and above)
08-20-2020 05:57 AM
ASAv100 (16core) is only supported with software release 9.14.1.6 or higher. It looks like you are running software version 9.12.3.12 which does not support 16core VMs.
08-20-2020 06:07 AM
Hi Jim
below is sh version output, i have highlighted the HW part. i believe its ASAv30 and resource allotted is 1CPU with 4 cores.
AZU-WEU-FW-01# sh version
Cisco Adaptive Security Appliance Software Version 9.12(3)12
SSP Operating System Version 2.6(1.198)
Device Manager Version 7.13(1)
Compiled on Fri 17-Apr-20 10:50 PDT by builders
System image file is "(hd0,1)/asa9-12-3-12-smp-k8.bin"
Config file at boot was "startup-config"
AZU-WEU-FW-01 up 28 mins 9 secs
Hardware: ASAv, 14336 MB RAM, CPU Xeon E5 series 2400 MHz, 1 CPU (4 cores)
Model Id: ASAv30
Internal ATA Compact Flash, 9216MB
Slot 1: ATA Compact Flash, 9216MB
BIOS Flash Firmware Hub @ 0x0, 0KB
0: Ext: Management0/0 : address is 000d.3a47.38dc, irq 0
1: Ext: GigabitEthernet0/0 : address is 000d.3a47.38f1, irq 0
2: Ext: GigabitEthernet0/1 : address is 000d.3a47.35cc, irq 0
3: Ext: GigabitEthernet0/2 : address is 000d.3a47.360a, irq 0
License mode: Smart Licensing
ASAv Platform License State: Licensed
Active entitlement: ASAv-STD-100M, enforce mode: Authorized
Licensed for maximum of 1 vCPU
Installed license is insufficient for the instance type deployed. Performance is reduced with the currently installed license.
Licensed features for this platform:
Maximum VLANs : 200
Inside Hosts : Unlimited
Failover : Active/Standby
Encryption-DES : Enabled
Encryption-3DES-AES : Enabled
Security Contexts : 0
Carrier : Enabled
AnyConnect Premium Peers : 50
AnyConnect Essentials : Disabled
Other VPN Peers : 750
Total VPN Peers : 750
AnyConnect for Mobile : Enabled
AnyConnect for Cisco VPN Phone : Enabled
Advanced Endpoint Assessment : Enabled
Shared License : Disabled
Total TLS Proxy Sessions : 500
Botnet Traffic Filter : Enabled
Cluster : Disabled
Serial Number: XXXXXXXXX
Image type : Release
Key version : A
Configuration last modified by enable_1 at 14:19:53.189 CEST Thu Aug 20 2020
08-20-2020 06:40 AM
But as per the version it show as "Active entitlement: ASAv-STD-100M"
08-20-2020 07:18 AM
Sorry, I mistakenly thought you were using the new ASAv100 license.
Is it possible for you to upgrade to software version 9.13.1 or later? In that release we made it so that you can run any license on any sized VM (#vCPUs, amount of memory). If that is not possible then for the 9.12 release, if you want to run an ASAv-STD-100M license then you can only run on a VM with 1 vCPU and a maximum of 2GB of memory.
08-21-2020 03:01 AM
Hi Jim,
Thanks for the reply. When the issue started the ASAv was on 9.12.1 and we upgrade to 9.12.3 to mitigate this. This was unsuccessful and the reboots still persist. This configuration worked for us since a year with no issues found. I would try to upgrade to 9.13.1 or higher release and check.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide