Please explain this configuration. What kind of NAT is it using and how can I learn how to configure it? nat(any,outside) source static OBJECT-GROUP-1 OBJECT-GROUP-1 destination static OBJECT-GROUP-2 OBJECT-GROUP-2 no-proxy-arp route-lookupnat(any,o...
Is there a way from the CLI to display a list of contexts configured when the ASA has multiple contexts?
Bonjour à tous J'ai un problème de circulation entre deux sites distants entre ASA 5525 et Pfsense le cryptage du protocole est Ikev1 Ipsec Aes 128 SHA1 / Groupe 1 / PSK J'ai une connexion de téléchargement à 50 Mo / s et quand je télécharge un fic...
Hi I'm trying to access ASDM from internal interface in order to configure site to site vpn to build my configuration prior to shipping and before client's network become usable the problem is I cannot access ASDM https://10.10.10.1 is not working...
Hi Moderator,I have the following query with regards to Firewall.1) Will global nat forward the traffic to respective gateways of ISP i.e Global ID 13, should always forward to 100.X.X.X and 14 should 200.X.X.X through default route.2) In the event ...
Hi Experts, any update on the release date of FTD 6.3? last time I checked it was supposed to be released Q2 CY17, and what features should we expect to be there? Context support, FDM on 4100 & 9300, PBR, clustering for 15 nodes ...etc Thanks Wise
Dear All, I have configured my FTD 6.2.3 through FDM with base, threat and malware license and all the policies are working fine. But today when i open the FDM it says license are out of compliance what causing the issue.??? please help.....
Hi All, What is the general recommendation for which rules are inspected with IPS/File and which are not? I'm currently working on a deployment which has a large number of inside to outside zone rules that permit traffic such as dns, http, https, ftp...
Hello need advice on how to identify who is using an IPSec tunnelcan not capture packets using because of encryption, correct ? if I do a show vpn-seas l2l I see the tunnel peer and the destination which is the Asa outside interface I need to identif...
Dears Please find the attached topology. I have some problem in understanding the fail over, whenever the port channel interface of DC-1 fails it shifts over to DC-2 FW but the perimeter firewalls doesn't shift and the traffic gets drops, hence if I ...
Dear Expert, I may Etherchannel on FTD 2110 appliance is staying in down state. When configuring on FMC I used active has state. PLease Help me with your Expertise to solve this. regards, Zanga
I have a very unusual situation. I have an ASA 5515-x running Cisco Adaptive Security Appliance Software Version 9.1(4) I have a stuck static route that I cannot remove from the device. I have tried clear configure route BGPDMZ:cerberus-01(config)# c...
I'm using ASA 5506-X. I have an external network, whose computers need to SSH into the ASA. To do this I configured:ssh x.x.x.x x.x.x.x outsideWhere x.x.x.x x.x.x.x is the external address range of the outside network somewhere else in the world.Wi...
Firepower Management Centre stops recording the user to IP mapping info and creates the ‘User Identity Dropped: User Limit Reached’ messages at between 17,000 and 18,000 users, this is nowhere near the 50k license limit for users.
I'm using an ASA 5506X and I wish to configure two site-to-site vpn tunnels, which go to two other sites with their own ASA's But the second VPN is not accepting the final configuration step of applying the crypto map to the outside interface. Why no...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 08-25-2026 06:22 PM | ||
| 08-24-2026 12:26 AM | ||
| 08-20-2026 05:54 AM | ||
| 08-19-2026 07:59 AM | ||
| 08-10-2026 08:58 AM |
| User | Count |
|---|---|
| 4 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |
