Cisco licensing provided me an IPS license, I installed it but IPS is showing it as an expiredLicense(with no expiration date). Now I got a new license (with expiration date) but now I cannot install it (see attached error). I need to reset or delete...
Forum Posts
Hello, I have a Firepower 2110 integrated with FMC. I have several VPNs-Site-to-Site configured. The concentrator is the Firepower and my remote peers are all meraki. We want to homologate that these VPNs work between Merakis only. So, I am trying ...
Resolved! ASA deny TCP no connection
Hi Everyone, User is trying to download some application from cloud and getting error message Need to know if there is some issue on our end or server is denying the connection Dec 06 2017 12:57:16: %ASA-6-305011: Built dynamic TCP translation fr...
Resolved! Report dont finish generate nor fails
I have network risk report running on a weekly basis. Normally it takes 1 hour. But now it wont finish. As seen on the attached: it just stays like that. When im in reporting tab it says its queued. I tried to start another one just to see if it ...
Resolved! Best Firewalling Option For Server Farms
Gents, I'm working on a design scenario of a network Divestiture where company (A) needs it's data center resources to be completely protected from Company (B) and company (B) also wants protection from company (A). As you can see below topology ...
Hi all, after installing license for my firepower, I am facing issue with my ASDM launcher, As soon as I logged in to ASDM, it's just hang and not able to see anything. only thing I can see is left side panel, but if I click any of the function like...
I am trying to replace my secondary firewall and iam getting error " no response from mate " I can ping the failover interfaces ASA1---------------failoverfailover lan unit primaryfailover lan interface FOLINK TenGigabitEthernet0/9failover polltime...
Hi I have an ASA 5525X and I installed Firepower 6.1 on it s hard disk , the installation completed successfully , when i execute "sh module sfr " is shows Mod Status Data Plane Status Compatibility---- ------------------ --------------------- -----...
Hi, I am trying to understand how the state information is kept in firepower module running on ASA. I know ASA is stateful and keeps track of connections and automatically allow return traffic to pass. What about the firepower module? Does it maintai...
Hello!Today I was struggling a bit about configuring Cisco FTD (on ASA5506X) with a bypass.Background:A customer has a Cisco 886VA router with a VLAN trunk to its main switch (Cisco 3750).The VLAN trunk carries VLAN 1 (internal LAN) and VLAN 2 (guest...
Hi Guys, I have been able to connect to my FTP server just fine. I started loosing connection to the server as soon as I log on. I have tried several workstations on the network and I am faced with the same problem. I haven't changed any configuratio...
Resolved! multi port forwarding ASA 5510
Hello, i'm trying to configure RDP access to two internal hosts. There is a config of ASA: Cisco Adaptive Security Appliance Software Version 9.1(7)15Device Manager Version 7.8(2)151 System IP Addresses: Interface Name IP address Subnet mask Method ...
Hi, We are running two 5525x in HA, with multiple contexts. When we force a failover, one context doesn't failover, and connectivity is lost. In the failed senario, we are able to ping end-points from the failed contexts inside interface, but trave...
We are planning to move from ASA SourceFire 6.2.2 to FirePower Threat Defense. Our concern 1) AnyConnect 2) Quality of Service 3) NAT 4) IPv6 Are these features supported & What do you advice? What migration tools should I use? Is there any po...
Hi, I have configured management IP for mgmt 0/0 but while running, ">show interface ip brief" command the IP address for management interface showing unassigned. where it is showing in ">show network" output. Please help
